Instruction/ maintenance manual of the product GR50 Husqvarna
Go to page of 40
GR41 GR50 RS44 RS52 Oper ator ′ s manual Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine .
2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or f atal injur y to the operator or others. It is e xtremely impor tant that you read and understand the contents of the operator’ s manual.
English – 3 CONTENTS Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . KEY T O SYMBOLS Symbols ....................................................................... 2 CONTENTS Contents ...............
4 – English INTR ODUCTION Dear Customer , Cong ratulations on y our choice to buy a Jonsered product! W e are convinced that you will appreciate with g reat satisfaction the quality and perf ormance of our product for a v er y long time to come.
English – 5 WHA T IS WHA T? What is what on the c learing saw? (GR41/GR50/RS44) 23 24 1 Blade 2 Grease filler cap , bev el gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Thrott.
6 – English WHA T IS WHA T? What is what on the c learing saw? (RS52) 1 Blade 2 Grease filler cap , bev el gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Sto.
English – 7 GENERAL SAFETY PRECA UTIONS Impor tant P ersonal pr otective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PRO TECTION W ear hear ing protection that pro vides adequate noise reduction.
8 – English GENERAL SAFETY PRECA UTIONS Mac hine ′′ ′ ′ s safety equipment This section descr ibes the machine ′ s saf ety equipment, its pur pose , and how checks and maintenance should be carried out to ensure that it operates correctly .
English – 9 GENERAL SAFETY PRECA UTIONS Cutting attachment guar d This guard is intended to pre vent loose objects from being thrown to wards the operator . The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cr acked.
10 – English GENERAL SAFETY PRECA UTIONS F or mufflers it is very impor tant that you f ollow the instructions on checking, maintaining and servicing your machine. See instructions under the heading Checking, maintaining and ser vicing the machine’ s safety equipment.
English – 11 GENERAL SAFETY PRECA UTIONS Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting perf or mance . • Extend the lif e of cutting equipment.
12 – English GENERAL SAFETY PRECA UTIONS Sharpening the sa w blade • See the cutting attachment packaging f or correct shar pening instructions. A correctly shar pened b lade is essential for w or king efficiently and to av oid unnecessar y wear to the b lade and clearing saw .
English – 13 ASSEMBL Y Assembling the handlebar and thr ottle (GR41/GR50) • Remov e the screw at the rear of the throttle handle . • Slide the throttle handle onto the right side of the handlebar , (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar .
14 – English ASSEMBL Y Assembling the cutting equipment Fitting a blade guar d, grass blade and grass cutter • The blade guard (A) is fitted using 4 scre ws (L) and the suppor t plate (M) as shown. CA UTION! Alwa ys use the recommended guard f or the cutting attachment you are using.
English – 15 ASSEMBL Y guard as possible . T o tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread). When loosening and tightening the saw b lade nut, there is a risk of injur y from the teeth of the saw b lade.
16 – English ASSEMBL Y Adjusting the harness and c learing saw Standar d harness Safety release At the front is an easily accessible , quick release . Use this if the engine catches fire or in any other emergency situation that requires you to free y ourself from the machine and harness.
English – 17 ASSEMBL Y 4 Adjust the height of the suspension hook as described in the instructions for the standard harness. (Forestry clearing) 5 If you need to lo wer the suspension hook, f or tr imming f or e xample, mov e the suspension strap (A) to the low er mounting point on the backplate .
18 – English FUEL HANDLING Fuel safety Ne ver star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate . 2 If you ha ve spilt fuel on y ourself or your clothes , change your clothes . W ash any part of your body that has come in contact with fuel.
English – 19 FUEL HANDLING Mixing • Alwa ys mix the petrol and oil in a clean container intended f or fuel. • Alwa ys star t by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.
20 – English ST AR TING AND ST OPPING Chec k before starting • Check the b lade to ensure that no cracks ha ve f ormed at the bottom of the teeth or by the centre hole .
English – 21 ST AR TING AND ST OPPING Starting Hold the body of the machine on the ground using y our left hand (CA UTION! Not with your f oot!). Gr ip the starter handle, slowly pull out the cord with y our right hand until you feel some resistance (the star ter pawls g rip), now quickly and powerfully pull the cord.
22 – English W ORKING TECHNIQUES General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine.
English – 23 W ORKING TECHNIQUES W orking methods • Bef ore you star t clearing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollo ws etc. • Star t at whiche ver end of the area is easiest, and clear an open space from which to work.
24 – English W ORKING TECHNIQUES • T o fell a tree f orwards , the bottom of the tree should be pulled backw ards. Pull the blade backw ards with a quick, firm movement. • Large stems must be cut from two sides . First determine which direction the stem will f all.
English – 25 W ORKING TECHNIQUES Grass trimming with a trimmer head T rimming • Hold the trimmer head just above the g round at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Ne ver press the cord into the area to be cut.
26 – English MAINTENANCE Carb urettor Y our Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes.
English – 27 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T , if it is necessar y to readjust. First tur n the idle adjustment scre w T clockwise until the cutting attachment starts to rotate.
28 – English MAINTENANCE Muffler CA UTION! Some mufflers are fitted with a catalytic conv er ter . See chapter on T echnical data to see whether your machine is fitted with a catalytic conv er ter . The muffler is designed to reduce the noise le vel and to direct the e xhaust gases awa y from the operator .
English – 29 MAINTENANCE Bevel gear The be vel gear is filled with the right amount of grease at the f actor y . Howe ver , before using the machine y ou should check that the be vel gear is filled 3/4 full with grease . Use JONSERED special grease.
30 – English MAINTENANCE Maintenance sc hedule The f ollowing is a list of the maintenance that must be perf or med on the machine . Most of the items are described in the Maintenance section. The user m ust only carr y out the maintenance and service wor k described in this Operator’ s Manual.
English – 31 TECHNICAL D A T A T echnical data Note 1: Noise emissions in the environment measured as sound po wer (L W A ) in conf ormity with EC directive 2000/14/EC .
32 – English TECHNICAL D A T A Note 1: Noise emissions in the environment measured as sound po wer (L W A ) in conf ormity with EC directive 2000/14/EC .
English – 33 TECHNICAL D A T A EC-dec laration of conformity (Applies to Eur ope onl y) W e, Jonsered, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saws Jonsered GR41, .
1 Poly T rim 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10.
1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII.
.
2,7-3,3 mm .106-.130" 15 cm 6" 15 cm 6" 15 cm 6" 15 cm 6" 1 2 3 5 6 7 10 11 1.) 2.) >1,1 Kw <1,1 Kw 2,7 mm - 9,0 m 3,0 mm - 7,5 m 3,3 mm - 6,0 m 4 8 Auto 55.
´®z+Rq,¶60¨ ´®z+Rq,¶60¨ "Clic" 1 2 3 5 6 7 9 10 m 32' 4 8 4,3 m 14' 2,7-3,3 mm .106-.13" 10 cm 4" 6" 15 cm T ap n’Go 45.
.
´®z+Rq,¶60¨ 2007-04-02 ´®z+Rq,¶60¨ 1150811-26.
An important point after buying a device Husqvarna GR50 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna GR50 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna GR50 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna GR50 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna GR50 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna GR50, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna GR50.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna GR50. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna GR50 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
