Instruction/ maintenance manual of the product CT16 Husqvarna
Go to page of 15
CT16 Owner's Manual 601 00 18-54 Reference No. 337411 05/03/95 8 1.1996 Spare P ar ts Piéces Dètachées.
2 SAFETY RULES THESE SAFETY RULES ARE FOR YOUR PROTECTION. READ THEM CAREFULLY LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS ATTENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY.
3 Record the following information about your unit so that you will be able to provide it in case of loss or theft. CITY: STATE: TELEPHONE: PURCHASE DATE: MODEL NUMBER: / / SERIAL NO.
4 Figure 4 Figure 5 LOWER END OF HANDLE TINE SHIELD MOUNTING CHANNEL FIG. 1-OP on page 6 shows the tiller/cultivator completely assembled. Reference to the right and left hand side of the tiller/cultivator is from the operator's position behind the unit.
5 IMPORTANT: OVERTIGHTENING THE SCREWS ENOUGH TO CHANGE THE SHAPE OF THE HANDLES CAN RESULT IN DAMAGE TO THE ENGINE CASTING. ● Hold the curved head carriage bolt against theoutside of the lower handle while tightening the tee knobs securely. TO INSTALL THE THROTTLE CON- TROL ASSEMBLY ● Place a No.
7 UPPER HANDLE THROTTLE CONTROL LEFT SIDE LOWER HANDLE TINE SHIELD DEPTH ROD/ TRANSPORT WHEELS RIGHT SIDE LOWER HANDLE CULTIVATOR TINES THROTTLE CONTROL - Controls the engine speed and the tine rotation. This tiller/cultivator is equipped with a centrifugal clutch that engages the tine drive system when the engine speed is increased.
8 The operation of this tiller/cultivator can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating the tiller/cultivator. We recommend standard safety glasses or Wide Vision Safety Mask for over your glasses.
9 GAS OIL GAS OIL 1 Gal. 5 oz. 4 Liters .167 L 2 Gal. 11 oz. 8 Liters .333 L 5 Gal. 27 oz. 20 Liters .833 L U. S. S. I. (METRIC) ● Tilt the tiller/cultivator back on the depth rod or transport wheels to raise the tines off the ground.
10 FIGURE 7 DEPTH ROD IN TILLING POSITION FIG. 2-OP TILLING HINTS ● Tilling is digging in, turning over and breaking up packed soil before planting. Loose unpacked soil helps root growth. Best tilling depth is 4 to 6 inches. Tilling will also clear the soil of unwanted vegetation.
11 GENERAL The warranty on this tiller/cultivator does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main- tain the tiller/cultivator as instructed in this manual.
12 ENGINE AIR CLEANER The air cleaner filter should be cleaned and reoiled after 3 months or 25 hours of operation. Clean more often under dusty conditions. IMPORTANT: The engine can be worn out in a very short period of time if dirt or grit is allowed to enter the engine.
13 LEFT SIDE TINES RIGHT SIDE TINES CLEVIS PINS HAIRPINS FRONT VIEW RIGHT SIDE INDICATOR PROPERLY INSTALLED RIGHT SIDE TINES TINE REPLACEMENT The tiller/cultivator is left hand or right hand as viewed from the operator's position behind the unit.
14 CARBURETOR ADJUSTMENT A dirty air cleaner will cause the engine to run improperly and/or smoke excessively. Be sure the air cleaner is clean before adjusting the carburetor. Never make unnecessary adjustments to the carburetor. The carburetor was set at the factory to operate efficiently under most applications.
15 ● Drain the fuel from the fuel tank into an approved container outdoors, away from open flame. ● Start and run the engine until it stops due to lack of fuel. ● Pull the starter handle slowly until you feel resistance due to compression pressure, then stop.
16 Drain fuel tank. Fill with fresh mixture. Check fuel mix chart and mix fresh fuel. Clean fuel tank. Fuel tank should be half full when starting engine. See carburetor adjustment section. Clean and re-gap plug. Clean and re-oil air cleaner. Blow dirt and debris off top of carburetor.
An important point after buying a device Husqvarna CT16 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna CT16 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna CT16 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna CT16 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna CT16 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna CT16, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna CT16.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna CT16. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna CT16 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
