Instruction/ maintenance manual of the product CHAIN SAW 266 Husqvarna
Go to page of 8
Chain saw model 266 Operator’ s manual TECHNICAL SPECIFICA TION Displacement . . . . 66.7 cm 3 Bore . . . . . . . . . . . 50 mm Stroke . . . . . . . . . . 34 mm Ignition advance . . . . . 25˚ bef ore t.d.c. at 8500 r pm Sparking Plug . . . . Champion CJ 7Y , P AL P8Y Electrode gap .
What is what on the chain saw? 1. Starter handle 7. Throttle trigger 2. Oil filler cap 8. Front hand guard 3. Starter 9. Chain brake activator 4. Adjusting screws, 10. Cylinder cover carburetor 11. Choke 5, Fuel filler cap 12. Throttle latch 6. Ignition switch 13.
Chain brake activator “Swed-o-Matic” The Swed-o-Matic should release the chain brake at a certain load on the guide bar tip. Adjusting the release power The distance between the Swed-o-Matic release screw and the front handle (B) determines the release power.
Starting the chain saw A. Cold engine . 1. Switch on the ignition (push the switch is visible). 2. Pull out the choke control. to the left so that the 1 3. Push down the throttle trigger lockout (A). 4. Open the throttle fully (B). 5. Push the throttle latch backwards (C).
! Cleaning the air filter A clean air filter is necessary for optimal carburetor function and optimal engine power. In order to get at the air filter, remove the cylinder cover by undoing the retaining screws and lifting the cover off upwards-backwards.
Winter use Assemble the remaining parts in reverse order Lift up the starter cord into the notch on the pulley. Tension the return spring by turning the pulley clockwise about two turns. NOTE! Make sure that it is possible to turn the pu//ey at least 1/4 of a turn further when the cord is fu//y pu//ed out.
Maintenance of the chain saw Daily maintenance 1. Clean the saw body from the outside. 2. Clean the air filter. Change if necessary. 3. Turn around the guide bar, lower edge up. Clean the bar groove. 4. Clean the fan and air intakes in the starter cover.
I Safety reminders Handling 1. When transporting the saw, fit the chain protection. 2. Do not smoke when filling the fuel tank. 3. Before cutting, fix the barking support properly 4. When using the saw, keep both hands on the handles. 5. Nobody is allowed to be within the swing area of the saw.
An important point after buying a device Husqvarna CHAIN SAW 266 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna CHAIN SAW 266 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna CHAIN SAW 266 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna CHAIN SAW 266 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna CHAIN SAW 266 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna CHAIN SAW 266, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna CHAIN SAW 266.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna CHAIN SAW 266. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna CHAIN SAW 266 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
