Instruction/ maintenance manual of the product BC 435B Husqvarna
Go to page of 9
XXXXXXX W ARNING • PLEASE READ For your own safety please read this manual before attempting to operate your new unit. F ailure to f ollow instr uctions can result in serious personal injur y . Spend a f ew moments to f amiliarize yourself with your trimmer before each use .
2 W ARNING! When using gas tools, basic safety precautions, including the following, should alwa ys be followed to reduce the risk of ser ious personal injury and/or damage to the unit. Read all these instructions before operating this product and save these instructions.
4 4 5 GE NE RA L ID EN TI FI CA TI ON 8 9 7 13 21 14 17 18 12 16 15 SAFETY FEA TURES 3 cutting attachment guard must be installed to pre vent debris from being thrown at the operator and prev ent the string from extending longer than necessary .
6 • “ LOOP WITH BARRIER ”HANDLE INS TALL ATION ( BC 4 3 5L ) • “ BULLHORN ¨ HANDLE INST ALLA TION (BC 435B) 1. T o install handle onto unit, you will need the f ollowing , ) A ( e l dnah” n r oh l l ub “ : t i kr e s u r uo y m o r f s t nenop m o c fix ing holder (B), clamp (C) and screws (D).
8 2. Install blade (C) with teeth pointing CLOCKWISE as shown in the illustration (Fig. 6B). 3. Install flange (E) with FLA T SURF ACE f acing blade (Fig. 6B). NO TE: Make sure blade is centered on collar arbor . 4. Tighten nut (B) securely by turning it COUNTER- CLOCKWISE with socket wrench (F) .
9 The trimmer is shipped WITHOUT OIL in the engine. NOTE: Fill oil before starting engine. Running the engine with too little or too much oil can cause engine damage. Check the engine oil level before each use, or every 10 hours if operated continuously.
11 • T O STOP ENGINE Release throttle trigger . Let engine retur n to idle. Push and hold ignition stop switch until engine stops . • ADDITIONAL SAFETY PRECAUTIONS Before oper ating your unit, revie w ALL SAFETY PRE- CA UTIONS in this manual.
13 • REPLA CING CUTTER LINE 1. T urn the nut (A) CLOCKWISE and remove it (Fig. 15A). 2. Remove the spool (C), and spring (D) from spindle (E). 3. Remove an y remaining cutter line. 4. Doubl ea 32' (9.8m) length of .095 or .105" (.24 or .27cm) cutter line.
15 TROUBLE SHOO TING THE ENGINE PROBLEM PROB ABLE CA USE CORRECTIVE A CTION Unit won’t start or star ts but will not run. Incorrect star ting procedures. Follo w instructions in the User Manual. Incorrect carburetor mixture adjustment setting. Ha ve carburetor adjusted b y an Authorized Service Center .
An important point after buying a device Husqvarna BC 435B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna BC 435B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna BC 435B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna BC 435B you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna BC 435B will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna BC 435B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna BC 435B.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna BC 435B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna BC 435B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
