Instruction/ maintenance manual of the product 50 Rancher Husqvarna
Go to page of 8
Chain saw 50 Rancher Owner’ s maintenance manual TECHNICAL SPECIFICA TION Displacement . . . . 48.7 cm 3 Bore . . . . . . . . . . . 44 mm Stroke . . . . . . . . . . 32 mm Ignition adv ance . . . . . 26˚ bef ore t.d.c. at 8400 r pm Sparking Plug . .
I WHAT IS WHAT ON THE CHAIN SAW? 8 11 %-- 5 1, Starter handle 8. 2. Oil filler cap 9. 3. Starter 10, 4. Front handle 11. 5. Fuel filler cap 12. 6. Ignition switch 13. 7. Throttle trigger 14. 6 7 --- Front hand guard Automatic chain brake Cylinder cover Choke Throttle latch Throttle trigger lockout Rear handle ASSEMBLING GUIDE BAR AND CHAIN A.
MAINTAINING THE CHAIN BRAKE This chain saw is equipped with a new type of automatic chain brake that has been adjusted at the factory. It will need no further adjust- ment. Release the chain brake as soon as you move or cease working even if it is for a short break.
CLEANING THE AIR FILTER In order to get at the air filter, remove the cylinder cover by undoing the three retaining screws and lifting the cover off upward% back- wards, Lift off the filter carefully to prevent dirt from falling down into the carburetor.
STARTING THE CHAIN SAW Cold engine . . . . . - _- ..-,’1, A$ 1. Switch on the ignition (push the ignition switch to the left so that the 1 is visible). 2. Push UII the choke control. 3. Push down the throttle trigger lockout (A). 4, Open the throttle fully (B).
MAINTENANCE OF THE CHAIN SAW 3 . . . . 0 . 4 10 14 13 Daily maintenance Weekly maintenance 1. 2, 3. 4, 5. 6. 7. 8. 9. Clean the saw body from the outside. 10. Check the starter, its cord and return spring Clean the air filter. ”Change if necessary. 11.
WINTER USE In winter, extreme cold and powdery snow can cause running prob- lems. The partition wall is prepared for cold working conditions. In the partition wall there is a hole, that is covered by .
I I 1018 401-26A 20. 1 I-62 Printed in Sweden mrmtr.~s Mo,,(. w.
An important point after buying a device Husqvarna 50 Rancher (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 50 Rancher yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 50 Rancher - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 50 Rancher you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 50 Rancher will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 50 Rancher, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 50 Rancher.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 50 Rancher. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 50 Rancher along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
