Instruction/ maintenance manual of the product 355FRM Husqvarna
Go to page of 44
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 355FX 355FXT 355RX 355FRM Oper ator ′ s manual Please r ead the operator’ s manual carefully and mak e sure you understand the instructions befor e using the machine.
KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’ s manual.
CONTENTS English – 3 Contents Note the f ollowing bef ore starting: • Please read the operator’ s manual carefully . KEY T O SYMBOLS Symbols ................................................................ 2 CONTENTS Contents ...................
4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River , for production of muskets .
English – 5 WHA T IS WHA T? What is what on the brush cutter? (355RX) 29 30 31 35 34 12 2 3 4 5 7 8 6 10 15 9 11 13 24 21 33 19 18 17 16 20 25 27 26 23 24 28 1 23 32 22 22 14 1 Locking nut 2 Bev el .
6 – English WHA T IS WHA T? What is what on the brush cutter? (355FX, 355FXT) 19 17 18 24 28 26 27 25 29 21 23 22 1 20 30 16 2 3 4 6 11 12 10 14 13 15 1 7 8 5 9 1 Locking nut 2 Bev el gear 3 Grease .
English – 7 WHA T IS WHA T? What is what on the brush cutter? (355FRM) x 2 27 28 30 29 9 8 7 20 19 21 1 6 5 17 18 22 23 24 25 26 16 2 3 4 11 10 14 13 15 12 1 Bev el gear 2 Grease filler cap, be vel.
GENERAL SAFETY PRECA UTIONS 8 – English Impor tant P ersonal protective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PRO TECTION Wear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approved e ye protection.
GENERAL SAFETY PRECA UTIONS English – 9 BOO TS Wear boots with steel toe-caps and non-slip sole . CLO THING Wear clothes made of a strong f abric and avoid loose clothing that can catch on twigs and branches. Alwa ys wear heavy , long pants. Do not wear je weller y , shorts sandals or go barefoot.
GENERAL SAFETY PRECA UTIONS 10 – English be check ed. See instr uctions under the heading Maintenance. Stop switc h Use the stop s witch to switch off the engine. Star t the engine and make sure the engine stops when you mov e the stop switch to the stop setting.
GENERAL SAFETY PRECA UTIONS English – 11 cutter . Cer tain har nesses also hav e a quick release fitted to the suppor t hook. Check that the harness straps are correctly positioned. Once the harness and machine have been adjusted, check that the harness quick release works correctly .
GENERAL SAFETY PRECA UTIONS 12 – English should operate the soc ket spanner when loosening or tightening the nut. The nylon lining inside the locking n ut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.
GENERAL SAFETY PRECA UTIONS English – 13 incorrectly sharpened or damaged blade increases the risk of accidents. K eep the correct setting on the saw blade! F ollow our instructions and use the recommended setting tool. An incorrectly set saw b lade increases the r isk of jamming and blade thrust, and damage to the saw b lade.
GENERAL SAFETY PRECA UTIONS 14 – English T rimmer head • Only use the recommended trimmer heads and trimmer cords. These have been tested b y the manuf acturer to suit a par ticular engine size. This is especially impor tant when a fully automatic trimmer head is used.
ASSEMBL Y English – 15 Assembling the handlebar and throttle CA UTION! Some models have the throttle handle fitted at the factory . • Remov e the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar , (see diagram).
ASSEMBL Y 16 – English Fitting the blade guar d/ combination guard, grass b lade and ball-bearing-mounted support cup • Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft.
ASSEMBL Y English – 17 355RX • Fit the holder (R) and brack et (J) with 2 bolts (H) on the gear housing. • Then fasten the b lade guard (A) with 4 bolts (L) in the holder (N).
ASSEMBL Y 18 – English • Fit the drive disc (B) on the output shaft. • T urn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Inser t the locking pin (C) in the hole to loc k the shaft.
ASSEMBL Y English – 19 Adjusting the harness and brush cutter T riobalance harness Safety release Push down the red release le ver to release the machine from the harness. Adjusting the harness 1 Tighten the hip strap so that it sits securely . 2 Tighten the chest strap under your left arm so that it fits closely around your body .
ASSEMBL Y 20 – English Adjust the height using the strap on the harness for the suppor t hook. 2 Grass clearing The machine should be supported in a har ness when grass clearing so that the cutting equipment is parallel to the ground.
FUEL HANDLING English – 21 Fuel safety Nev er star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate. 2 If you ha ve spilt fuel on yourself or y our clothes, change your clothes. W ash any par t of your body that has come in contact with fuel.
FUEL HANDLING 22 – English Mixing • Alwa ys mix the petrol and oil in a clean container intended for fuel. • Alwa ys star t by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.
ST AR TING AND ST OPPING English – 23 Check bef ore star ting • Check the b lade to ensure that no cracks hav e formed at the bottom of the teeth or by the centre hole.
ST AR TING AND ST OPPING 24 – English W arm engine Use the same starting procedure as for a cold engine but without setting the choke control in the chok e position.
W ORKING TECHNIQ UES English – 25 General working instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot affect y our control of the machine.
W ORKING TECHNIQ UES 26 – English W orking methods • Before y ou star t clearing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollows etc. • Star t at whichev er end of the area is easiest, and clear an open space from which to work.
W ORKING TECHNIQ UES English – 27 conditions, so that cleared stems f all in the cleared area of the stand. Forestry clearing using a sa w blade • The risk of blade thrust increases with increasing stem size. Y ou should therefore a void cutting with the area of the blade between 12 o'cloc k and 3 o'clock.
W ORKING TECHNIQ UES 28 – English Brush cutting with a sa w blade • Thin stems and brush are mown down. Work with a sawing mov ement, swinging side ways. • T r y to cut sev eral stems in a single sawing mov ement. • With groups of hardwood stems, first clear around the group .
W ORKING TECHNIQ UES English – 29 • When trimming and clearing you should use less than full throttle so that the cord lasts longer and to reduce the wear on the trimmer head. Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower .
MAINTENANCE 30 – English Carburettor Y our Husqv ar na product has been designed and manuf actured to specifications that reduce har mful emissions.
MAINTENANCE English – 31 3 If the star t throttle speed is too low (below 4000 rpm), turn the adjuster screw A clockwise until the cutting attachment star ts to rotate.
MAINTENANCE 32 – English Cleaning the air filter (355FX, 355FXT) Remov e the air filter cover and take out the filter . Blow clean with compressed air . Cleaning the air filter (355RX, 355FRM) Remo v e the air filter cover and take out the filter .
MAINTENANCE English – 33 spark plug should be replaced after about a month in operation or earlier if necessary . CA UTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/ cylinder . Check that the spark plug is fitted with a suppressor .
MAINTENANCE 34 – English par ticular attention that the opening on the air duct is positioned in the centre of the hole in the air filter holder . IMPORT ANT! If the temperature rises abov e -5 ° C or 0 ° C respectively the machine MUST be restored to its normal set-up.
English – 35 MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carr y out the maintenance and service wor k described in this Operator’ s Manual.
36 – English TECHNICAL D A T A T ec hnical data Note 1: Noise emissions in the en vironment measured as sound pow er (L WA ) in conf ormity with EC directive 2000/14/EC . Reported sound power le vel f or the machine has been measured with the original cutting attachment that giv es the highest le vel.
English – 37 TECHNICAL D A T A 355FX, 355FXT Appro ved accessories T ype Cutting attachment guard, Art. no. Centre hole in blades/cutters , Ø 25,4 mm Output shaft thread M12 Grass blade/g rass cutt.
38 – English TECHNICAL D A T A EC-declaration of conf ormity (Applies to Europe onl y) W e, Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel: +46-36-146500, declare that the brush cutters Husqv arna.
1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII.
.
2,7-3,3 mm .106-.130" 15 cm 6" 15 cm 6" 15 cm 6" 15 cm 6" 1 2 3 5 6 7 10 11 1.) 2.) >1,1 Kw <1,1 Kw 2,7 mm - 9,0 m 3,0 mm - 7,5 m 3,3 mm - 6,0 m 4 8 Auto 55.
"Clic" 1 2 3 5 6 7 9 10 m 32' 4 8 4,3 m 14' 2,7-3,3 mm .106-.13" 10 cm 4" 6" 15 cm T45, T45x.
A 2,7 - 4,0 mm / .105 - .160" B 8 m / 26’ C 15 cm / 5.9" 1 2 3 5 6 7 9 4 8 6" 15 cm B C A T55x "Clic".
1153302-26 ´®z+U>6¶6G¨ ´®z+U>6¶6G¨ 2010-03-08 Original instructions.
An important point after buying a device Husqvarna 355FRM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 355FRM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 355FRM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 355FRM you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 355FRM will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 355FRM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 355FRM.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 355FRM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 355FRM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
