Instruction/ maintenance manual of the product 327LDX-series Husqvarna
Go to page of 36
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 327LD X-series Oper ator ′ s manual Please r ead the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.
KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’ s manual.
CONTENTS English – 3 Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . KEY T O SYMBOLS Symbols ................................................................ 2 CONTENTS Contents ......................
4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River , for production of muskets .
English – 5 WHA T IS WHA T? What is what? 1 3 2 4 20 4 21 19 9 8 12 13 14 15 16 17 18 22 23 24 1 5 6 7 10 11 1 T rimmer head 2 Grease filler cap, be vel gear 3 Bev el gear 4 Cutting attachment guar.
GENERAL SAFETY PRECA UTIONS 6 – English Impor tant P ersonal protective equipment HELMET A protectiv e helmet where there is a risk of falling objects HEARING PRO TECTION Wear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approved e ye protection.
GENERAL SAFETY PRECA UTIONS English – 7 BOO TS Wear sturdy , non-slip boots. CLO THING Wear clothes made of a strong f abric and avoid loose clothing that can catch on twigs and branches. Alwa ys wear heavy , long pants. Do not wear je weller y , shor ts sandals or go barefoot.
GENERAL SAFETY PRECA UTIONS 8 – English Stop s witch Use the stop s witch to switch off the engine . Star t the engine and mak e sure the engine stops when you mov e the stop switch to the stop setting. Cutting attac hment guard This guard is intended to pre vent loose objects from being thrown tow ards the operator .
GENERAL SAFETY PRECA UTIONS English – 9 Nev er use a machine that has a faulty muffler . Regularly check that the muffler is securely attached to the machine. If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly .
ASSEMBL Y 10 – English Fitting the loop handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. Fit the nut, knob and screw . Do not ov er tighten.
ASSEMBL Y English – 11 Assembling the cutting equipment Fitting the trimmer guard and trimmer head • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the tr immer guard/combination guard onto the fitting on the shaft and secure with the bolt (L).
FUEL HANDLING 12 – English Fuel safety Nev er star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate. 2 If you ha ve spilt fuel on yourself or y our clothes, change your clothes. W ash any par t of y our body that has come in contact with fuel.
FUEL HANDLING English – 13 Mixing • Alwa ys mix the petrol and oil in a clean container intended for fuel. • Alwa ys star t by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.
ST AR TING AND ST OPPING 14 – English Check bef ore star ting • Check that the support flange is not cracked due to fatigue or due to being tightened too m uch. Discard the suppor t flange if it is crack ed. • Ensure the locking nut has not lost its captiv e force.
ST AR TING AND ST OPPING English – 15 apply full throttle; the throttle will automatically disengage from the star t setting. CA UTION! Do not pull the star ter cord all the way out and do not let go of the star ter handle when the cord is fully extended.
W ORKING TECHNIQ UES 16 – English General working instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot affect y our control of the machine.
W ORKING TECHNIQ UES English – 17 Basic working tec hniques Alwa ys slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Grass trimming with a trimmer head T rimming • Hold the trimmer head just above the ground at an angle.
MAINTENANCE 18 – English Carburettor Y our Husqvarna product has been designed and manuf actured to specifications that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.
MAINTENANCE English – 19 Low speed jet L T r y to find the highest idle speed by turning the low speed jet L clockwise then anti-cloc kwise. When the highest speed has been found, turn the low speed jet L 1/4 turn anti-clockwise.
MAINTENANCE 20 – English Muffler CA UTION! Some mufflers are fitted with a catalytic conv er ter. See chapter on T echnical data to see whether your machine is fitted with a catalytic con ver ter . The muffler is designed to reduce the noise le vel and to direct the exhaust gases a way from the oper ator.
MAINTENANCE English – 21 If the machine is low on pow er, difficult to start or runs poorly at idle speed: alw ays check the spark plug first before taking an y fur ther action. If the spark plug is dirty , clean it and check that the electrode gap is 0.
MAINTENANCE 22 – English Bevel gear The bev el gear is filled with the right quantity of grease at the factory . Ho wev er, bef ore using the machine you should check that the be vel gear is filled three-quarters full with grease. Use HUSQV ARNA special grease.
English – 23 MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carr y out the maintenance and ser vice work described in this Operator’s Manual.
24 – English TECHNICAL D A T A T ec hnical data Note 1: Noise emissions in the environment measured as sound power (L W A ) in conformity with EC directive 2000/14/ EC.
English – 25 TECHNICAL D A T A The follo wing attachments are recommended for the specified models. The follo wing attachments have been de veloped mainly f or the Husqvarna 125LD tr immer , but can also be used with the specified models.
.
"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35.
1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5.
T35, T35x "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm.
"Clic" 1 2 3 5 6 7 9 6,0 m 18' 4 8 3,05 m 9' 2,0-2,4 mm .079-.095" 10 cm 4" 6" 15 cm T25.
.
.
.
.
.
1151209-26 ´®z+S4|¶6|¨ ´®z+S4|¶6|¨ 2008-08-29.
An important point after buying a device Husqvarna 327LDX-series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 327LDX-series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 327LDX-series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 327LDX-series you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 327LDX-series will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 327LDX-series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 327LDX-series.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 327LDX-series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 327LDX-series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
