Instruction/ maintenance manual of the product 325RJ Husqvarna
Go to page of 33
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 323RJ 325RJ X-SERIES Oper ator’ s manual (EP A) Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols W ARNING! Clear ing saws , brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and theref ore reser ves the right to modify the design and appearance of products without prior notice.
4 – English SAFETY INSTR UCTIONS P ersonal pr otective equipment GLO VES Glov es should be wor n when necessar y , e.g., when fitting cutting attachments. HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection.
English – 5 SAFETY INSTR UCTIONS Vibration damping system Y our machine is equipped with a vibration damping system that is designed to minimise vibration and mak e operation easier . Use of incorrectly wound cord or an incorrect cutting attachment increases the le vel of vibr ation.
6 – English SAFETY INSTR UCTIONS Chec king, maintaining and servicing the machine ′ s safety equipment Throttle loc k • Make sure the throttle control is loc ked at the idle setting when the throttle lock is released. • Press the throttle lock and mak e sure it retur ns to its original position when you release it.
English – 7 SAFETY INSTR UCTIONS Muf fl er • Ne ver use a machine that has a f aulty muffler . • Regularly check that the muffler is securely attached to the machine. • If the muffler on y our machine is fitted with a spark arrestor mesh then it should be cleaned regularly .
8 – English SAFETY INSTR UCTIONS Cutting equipment Sharpening grass cutters and grass blades • See the cutting attachment packaging f or correct shar pening instructions. • Shar pen blades and cutters using a single-cut flat file . • Shar pen all edges equally to maintain the balance of the blade .
English – 9 SAFETY INSTR UCTIONS Starting • The complete clutch cov er and shaft must be fitted before the machine is star ted, otherwise the clutch can come loose and cause personal injur y . • Ne ver start the machine indoors. Exhaust fumes can be dangerous if inhaled.
10 – English SAFETY INSTR UCTIONS General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine .
English – 11 SAFETY INSTR UCTIONS Grass trimming using a trimmer head and plastic blades T rimming • Hold the trimmer head just above the g round at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Nev er press the cord into the area to be cut.
12 – English WHA T IS WHA T? What is what on the trimmer? = 28 29 30 = 27 ¢ ¥ 1 T rimmer head 2 Grease fi ller cap 3 Bev el gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle contro.
English – 13 ASSEMBL Y Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fi tted between the arro ws on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and scre w .
14 – English ASSEMBL Y Fitting the blade guar d/combination guar d, grass blade and grass cutter • Hook the blade guard/combination guard (A) onto the fi tting on the shaft and secure with the bolt. CA UTION! Use the recommended blade guard. See the T echnical data section.
English – 15 FUEL HANDLING Fuel CA UTION! The machine is equipped with a two-strok e engine and must alwa ys been run using a mixture of gasoline and two-strok e engine oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained.
16 – English ST AR TING AND ST OPPING Chec k bef ore star ting F or saf ety reasons follo w these recommendations! • Check the b lade to ensure that no cracks hav e formed at the bottom of the teeth or by the centre hole .
English – 17 ST AR TING AND ST OPPING Air purge: Press the air purge diaphragm repeatedly until fuel begins to fi ll the diaphragm. The diaphragm need not be completely fi lled. Stopping Stop the engine by s witching off the ignition. Starting Hold the body of the machine on the ground using y our left hand (CA UTION! Not with your f oot!).
18 – English MAINTENANCE Carb urettor Y our Husqv arna product has been designed and manuf actured to speci fi cations that reduce har mful emissions.
English – 19 MAINTENANCE will run smoothly in ev er y position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. IMPOR T ANT! If the idle speed cannot be adjusted so that the cutting attachment stops, contact y our dealer/service workshop .
20 – English MAINTENANCE Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the star ter . 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder .
English – 21 MAINTENANCE Bevel gear The be vel gear is fi lled with the right quantity of grease at the f actor y . Howe ver , before using the machine y ou should check that the be vel gear is fi lled three-quarters full with grease. Use HUSQV ARNA special grease.
22 – English TECHNICAL D A T A T echnical data NO TE! Noise pressure at the user ’ s ear and vibr ation on the handles are measured with all the machine ’ s approved cutting equipment fi tted. The table indicates the highest and lowest v alues.
English – 23 FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv ar na Forest & Garden are pleased to e xplain the emissions control system warranty on your 2001 and later small nonroad engine .
1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm.
1 T ri Cut 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10.
1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6".
1 T rimmy Hit 23 4 5 6 7 8 9 10 11 “ Click ” “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .
1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6".
"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35.
´®z+H0=¶5V¨ ´®z+H0=¶5V¨ 1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5.
T35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm.
´®z+H0=¶5V¨ 2003-01-27 ´®z+H0=¶5V¨ 1140162-95.
English – 33 FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT.
An important point after buying a device Husqvarna 325RJ (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 325RJ yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 325RJ - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 325RJ you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 325RJ will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 325RJ, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 325RJ.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 325RJ. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 325RJ along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
