Instruction/ maintenance manual of the product 325LD Husqvarna
Go to page of 36
Oper ator's manual (EP A II) Please read these instructions car efully and make sur e you understand them bef ore using the machine. English 322L 323L 325C 325C X-SERIES 325L X-SERIES 325L XT-SER.
2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine.
English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal protective equipment .
4 – English The machine‘s saf ety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.
English – 5 SAFETY INSTR UCTIONS 4. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. U se of incorrectly wound cord or incorr ect cutting equipment increases the level of vibration.
6 – English 3. Cutting attachment guard • Ensure that the spray guard is undamaged and is not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" .
English – 7 SAFETY INSTR UCTIONS 6. Cutting equipment The section describes how through corr ect maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment.
8 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like.
English – 9 ! General w orking instructions SAFETY INSTR UCTIONS Basic working techniques • Always drop to idling speed after each working operation. Longer periods running at full throttle without loading the engine (that is without resistance, which the engine feels from the cutting equipment when trimming) can lead to serious engine damage.
10 – English SAFETY INSTR UCTIONS Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord.
English – 11 WHA T IS WHA T? What is what on the trimmer? 1. T rimmer head 2. Gr ease filler cap 3. Angle gear 4. Spray guar d 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. C ylinder cov er 11. S tarter handle 12.
12 – English ASSEMBL Y Assembl y of the trimmer head ! W ARNING! Under no circumstances ma y the cutting equipment be used without an appro ved guard fitted. See the chapter “T echnical data” . If the wr ong guard or a def ective guard is fitted this can cause serious personal injury .
English – 13 ASSEMBL Y Fitting the spra y guar d and trimmer head (325C) Guard • Fit the guard as shown in the diagram. Tighten securely. Trimmer head • Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. • Hold the dust cup with a spanner to prevent the shaft from rotating.
14 – English Fitting the spra y guar d and trimmer head (325C X ) • Fit the guard as shown in the diagram. Tighten securely. • Insert the locking pin into the hole to lock the axle.
English – 15 FUEL HANDLING Fuel mixture ! W ARNING! Alwa ys provide good ventilation when handling fuel. NO TE! The machine is fitted with a two-stroke engine and must always be run on a mixture of gasoline and two-stroke oil. I t is important to measure the quantity of oil accurately , to ensure the correct mixtur e ratio.
16 – English ST AR T AND ST OP Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.
English – 17 Fine adjustment • When the machine has been ” run-in ” the carburetor should be finely adjusted. The fine adjustment should be carried out by qualified person.
18 – English Correctly adjusted carburetor A correctly adjusted carburetor means that the machine accelerates without hesitation and the machine 4-cy cles a little at max speed. F urthermore, the cutting attachment must not rotate/mo ve at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration.
English – 19 MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4.
20 – English MAINTENANCE NO TE: U se only HUSQ V ARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Y our warranty does not cov er damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQ V ARNA.
English – 21 TECHNICAL D A T A T echnical data Engine Displacement, cu. in/cm 3 C ylinder bore, inch/mm S troke length, inch/mm Recommended max. speed, rpm I dling speed, rpm S peed of output shaft, rpm Max.
22 – English 325C X-series 1,50/24,5 1,34/34 1,06/27 11 000 - 11 700 2 700 11 700 0,9/ 9 000 Ye s No W albr o MB 20 Champion R CJ 7Y 0,02/0,5 Zama C1Q 1,06/0,5 9,3/4,2 92/97 2,5/2,1 3,2/2,2 4,4/4,2 6,2/8,4 T echnical data Engine Displacement, cu. in/cm 3 Cylinder bor e, inch/mm S troke length, inch/mm Recommended max.
English – 23 TECHNICAL D A T A Approved accessories Thread blade shaft 3/8 T rimmer head Cutting attachment guard Art No. 537 02 61-01 537 02 61-01 537 02 61-01 Type Trimmy Hit Junior (R) Trimmy Fix 3/8" (R) Trimmy Hit VII (R) Approved accessories Thread blade shaft M10 Plastic knives T rimmer head Cutting attachment guard Art No.
24 – English EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine.
English – 25 1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm.
26 – English 1 T ri Cut 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10.
English – 27 1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6".
28 – English 1 T rimmy Hit 23 4 5 6 7 8 9 10 11 “Click” “Click” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .
English – 29 1 T rimmy Hit Junior 2 5 6 7 8 9 10 12 “Click” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9' 1.) 2.) 11 15 cm 6" 15 cm 6".
30 – English 1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6".
English – 31 1 T rimmy Hit VI 2 5 6 3 4 7 8 9 10 11 “Click” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .
32 – English 1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII.
English – 33.
34 – English 6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 12 3 4 56 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 1 1" T rimmy VII ´+H)y¶5h¨.
English – 35.
2002W11 ´+H)y¶5h¨ 114 00 98-95.
An important point after buying a device Husqvarna 325LD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 325LD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 325LD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 325LD you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 325LD will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 325LD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 325LD.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 325LD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 325LD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
