Instruction/ maintenance manual of the product 325HD60, 325HD60X-Series, 325HD75X-Series Husqvarna
Go to page of 24
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 323HD60 325HD60 X-SERIES 325HD75 X-SERIES Oper ator’ s manual (EP A) Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols W ARNING! Incorrect or careless use of a hedge trimmer can tur n it into a dangerous tool that can cause serious or ev en fatal injury . It is e xtremely impor tant that you read and understand the contents of this operator’ s manual.
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and theref ore reser ves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment.
4 – English SAFETY INSTR UCTIONS P ersonal pr otective equipment GLO VES Glov es must be wor n when required, f or e xample when fitting, inspecting or cleaning cutting attachments HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction.
English – 5 SAFETY INSTR UCTIONS Hand guard The hand guard pre vents hands from coming into contact with the moving b lades, f or example, if the oper ator loses grip on the front handle. Vibration damping system Y our machine is equipped with a vibration damping system that is designed to minimise vibration and mak e operation easier .
6 – English SAFETY INSTR UCTIONS Chec king, maintaining and servicing the machine ′ s safety equipment Throttle loc k • Make sure the throttle control is loc ked at the idle setting when the throttle lock is released. • Press the throttle lock and mak e sure it retur ns to its original position when you release it.
English – 7 SAFETY INSTR UCTIONS Muffler • Ne ver use a machine that has a f aulty muffler . • Regularly check that the muffler is securely attached to the machine. • If the muffler on y our machine is fitted with a spark arrestor mesh this must be cleaned regularly .
8 – English SAFETY INSTR UCTIONS General safety precautions Starting • The complete clutch cov er and gear housing must be fitted bef ore the machine is star ted, otherwise the clutch ma y come loose and cause personal injur y . • Ne ver start the machine indoors.
English – 9 SAFETY INSTR UCTIONS Safety instructions when using the hedge trimmer CA UTION! Please read the operator’ s manual carefully and make sure y ou understand the instr uctions bef ore using the machine. P ersonal protection • Alwa ys wear boots and other equipment described under the heading P ersonal protective equipment.
10 – English SAFETY INSTR UCTIONS Safety instructions after completing w ork • The transpor t guard should alwa ys be fitted to the cutting attachment when the machine is not in use. • Make sure the cutting attachment has stopped bef ore cleaning, carr ying out repairs or an inspection.
English – 11 WHA T IS WHA T? What is what? 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 23 20 22 21 1 Operator’ s manual (EP A) 2 Grease filler cap 3 Gear housing 4 Blades 5 Cutter guard 6 F r.
12 – English FUEL HANDLING Fuel CA UTION! The machine is equipped with a two-strok e engine and must alwa ys been run using a mixture of gasoline and two-strok e engine oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained.
English – 13 FUEL HANDLING Fuelling • Clean the area around the fuel cap . Contamination in the tank can cause operating prob lems. • Ensure that the fuel is well mix ed by shaking the container bef ore filling the tank.
14 – English ST AR TING AND ST OPPING Chec k bef ore star ting • Inspect the working area. Remov e any objects that could be thrown out. • Check the cutting attachment. Nev er use blades that are dull, crac ked or damaged. • Check that the machine is in perf ect working order .
English – 15 ST AR TING AND ST OPPING W arm engine Ignition: Set the stop s witch to the star t position. Choke: Set the choke control in the chok e position and then back to its original position (B). This only engages the star t throttle setting without any chok e.
16 – English MAINTENANCE Carb urettor Y our Husqvarna product has been designed and manuf actured to specifications that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.
English – 17 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed with the idle adjustment screw T , if adjustment is necessar y . First turn the idle adjustment screw T clockwise until the b lades star t to move . Then tur n the idle adjustment screw T anticlockwise until the b lades stop.
18 – English MAINTENANCE Muf fl er CA UTION! Some muf fl ers are fi tted with a catalytic conv er ter . See chapter on T echnical data to see whether your machine is fi tted with a catalytic conv er ter . The muf fl er is designed to reduce the noise le vel and to direct the e xhaust gases aw a y from the operator .
English – 19 MAINTENANCE Cleaning the air fi lter Remov e the air fi lter cover and tak e out the fi lter . Wash it clean in warm, soapy w ater . Ensure that the fi lter is dr y before re fi tting it. An air fi lter that has been in use f or a long time cannot be cleaned completely .
20 – English MAINTENANCE Maintenance schedule Below y ou will fi nd some general maintenance instructions. If you need further information please contact your service workshop . Daily maintenance • Check throttle trigger and throttle trigger lock out function.
English – 21 MAINTENANCE Monthly maintenance • Clean the fuel tank. • Clean the outside of the carburettor and the space around it. • Clean the f an and the area around it. • Check fuel hose f or cracks or other damage . Change if necessar y .
22 – English TECHNICAL D A T A ´®z+H2)¶5O¨ ´®z+H2)¶5O¨ T echnical data Note 1: Equivalent noise pressure le v el is calculated as the time-weighted energy total f or noise pressure lev els under various working conditions with the follo wing time distr ibution: 1/2 idle and 1/2 max.
English – 23 FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv ar na Forest & Garden are pleased to e xplain the emissions control system warranty on your 2001 and later small nonroad engine .
´®z+H2)¶5O¨ 2003-02-11 ´®z+H2)¶5O¨ 1140180-95.
An important point after buying a device Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 325HD60, 325HD60X-Series, 325HD75X-Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
