Instruction/ maintenance manual of the product 317 EL, 321 EL Husqvarna
Go to page of 16
Oper ator´s manual 317 EL 321 EL Please read these instructions car efully and mak e sure you understand them bef ore using the machine. English.
ENGLISH 2 SYMBOLS USED IN OPERA T OR’S MANU AL: Do not use a coiled extension cord. Minimum wire cross-section: 1,5 mm ² Maximum cable length: 30 m V oltage: 230 V CAUTION! Chain saws are danger ous! Careless or impr oper use can result in sever e or fatal injury .
ENGLISH 3 Symbols 2 Important! Read before using chain saw 2 Contents 3 EC declaration of conformity 3 T echnical speci fi cations 4 Chain saw parts 5 Safe use 5 Starting and stopping 7 Daily inspect.
ENGLISH 4 Motor 1700 2000 Rated voltage V AC 220-240 230 Rated output W 1700 2000 Frequency Hz 50/60 50 Slip clutch Y es Y es Electronic start contr ol - Y es Electronic speed contr ol - Y es Electron.
ENGLISH 5 1. Rear handle 2. Power trigger lockout 3. Front handle 4. Serial No. plate 5. Chain tensioner 6. Chain oil reservoir 7. Chain oil level 8. V entilation slots 9. Power cable 10. Power trigger 11. Chain 12. Guide bar 13. Chain brake release button 14.
ENGLISH 6 • See to it that others keep their distance as long as the chain is in motion. Keep onlookers, children and animals away from the work ar ea. Do not let inexperienced persons handle the chainsaw or power cable. • Keep work area clear and well-lighted.
ENGLISH 7 D AIL Y INSPECTION AND MAINTENANCE CAUTION! Always disconnect the power before cleaning or performing maintenance. Here ar e a few general instructions for maintaining your hand- saw . If you are in doubt on any of these points, contact your service dealer .
ENGLISH 8 • T ake extreme care when cutting with the top chain (on the underside of a log). The force of the chain action pushes the saw backwards, and if the operator does not maintain fi rm control, the kickback danger zone may move far enough back into the kerf to produce a kickback.
ENGLISH 9 • The chain brake may be activated manually or by the force of inertia depending on the strength of the kickback and the position of the saw in relation to the object which made contact with the kickback danger zone.
ENGLISH 10 6. Replace the chain drive cover and screw the mounting nut hand tight. 7. T ension the chain by screwing the tensioning screw clockwise using the screwdriver tip on the combination tool. 8. Tighten chain fi rmly but not so hard that it does not turn easily by hand force.
ENGLISH 11 • Ensure that the cutter teeth are always correctly sharpened! Follow our instructions and use the recommended fi ling guide. A chain which is damaged or improperly maintained incr eases the risk of accident. • Maintain the correct depth-gauge height.
ENGLISH 12 Checking chain wear • Inspect chain every day for: - Visible cracks in rivets or links - Stiffness - Abnormal wear in rivets or links - Min. 3 mm (1/8”) horizontal cutter length - Any deviation on any of these points indicates a worn chain which must be discarded - Check the guide bar’ s oil passage and clean if necessary .
ENGLISH 13 See «T echnical Specifi cations» for the details which apply to your chain. It is very diffi cult to fi le a chain saw corr ectly with- out the proper aids. W e recommend the use of a fi le guide to ensure maximum cutting effi ciency with the least tendency to kickback.
ENGLISH 14 • Cutting a log supported at one end. The log is mor e than likely to splinter if cut straight through fr om the top down. - Make an initial cut fr om below (approx. 1/3 of the diameter) - Finish the cut fr om above. • Cutting a log supported at both ends.
ENGLISH 15 Danger zone A danger zone surrounds the tr ee to a distance of 2 1/2 times the height of the tree. See to it that no one is standing within this zone while you are felling the tree. Felling direction When felling a tree, one always aims to place it wher e neither objects nor diffi cult terrain will hamper limbing and cutting.
115 02 32-26 2006W11 ´®z+R76¶6°¨ T røskenveien 36 P .O.B. 10 N - 1708 Sarpsbor g Norway ´®z+R76¶6°¨.
An important point after buying a device Husqvarna 317 EL, 321 EL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 317 EL, 321 EL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 317 EL, 321 EL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 317 EL, 321 EL you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 317 EL, 321 EL will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 317 EL, 321 EL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 317 EL, 321 EL.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 317 EL, 321 EL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 317 EL, 321 EL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
