Instruction/ maintenance manual of the product 227L/LD Husqvarna
Go to page of 24
101 89 80-95 225L/LD 227L/LD 232L 240L Operator's manual (CARB, EP A) Read through the Operator‘s Manual carefully and understand the content before using the machine.
2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine.
English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment .
4 – English The machine‘s saf ety equipment This section describes the machine‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “ What is what“ to locate where this equipment is positioned on your machine.
English – 5 SAFETY INSTR UCTIONS 4. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. U se of incorrectly wound cord or incorr ect cutting equipment increases the level of vibration.
6 – English 3. Cutting attachment guard • Ensure that the spray guard is undamaged and is not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" .
English – 7 SAFETY INSTR UCTIONS 6. Cutting equipment The section describes how through corr ect maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment.
8 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like.
English – 9 ! General w orking instructions SAFETY INSTR UCTIONS Basic w orking techniques • Always trim at full throttle. • Always drop to idling speed after each working operation.
10 – English SAFETY INSTR UCTIONS Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord.
English – 11 WHA T IS WHA T? What is what on the trimmer? 1. T rimmer head 2. Gr ease filler cap 3. Angle gear 4. Spray guar d 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. S uspension for harness 11. C ylinder cover 12.
12 – English ASSEMBL Y Assembling the loop handlebar Assembly of the trimmer head I t is extremely important that the disc drive ’ s/support flange ’ s guide engages correctly in the cutting equipment’ s centre hole when assembling the cutting equipment.
English – 13 ASSEMBL Y Assembling other guards and cutting equipment B A L M C H Assembling and dismantling the two-part shaft (225LD, 227LD) • Fit the guard (A) intended for use with the trimmer head. Secure using four bolts (L) and the support plate (M) as shown in the diagram.
14 – English FUEL HANDLING Fuel mixture ! W ARNING! Always pr ovide good ventilation when handling fuel. NO TE! The machine is fitted with a two-stroke engine and must always be run on a mixture of gasoline and two-stroke oil. I t is important to measure the quantity of oil accurately , to ensure the correct mixtur e ratio.
English – 15 ST AR T AND ST OP Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.
16 – English Carburetor Y our H usqvarna product has been designed and manufactured to specifications that r educe harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in.
English – 17 Correctly adjusted carburetor A correctly adjusted carbur etor means that the machine accelerates without hesitation and the machine 4-cycles a little at max speed. Furthermor e, the cutting attachment must not rotate/mo ve at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration.
18 – English MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4.
English – 19 MAINTENANCE Spark plug The condition of the spark plug is affected by: • An incorrect carburetor setting. • An incorrect fuel mixture (too much or faulty oil). • A dirty air filter. These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties.
20 – English TECHNICAL D A T A 225L/LD 1,55/25,4 1,34/34 1,10/28 11 000-11 700 2 700 10 000 0,9 kW/ 9 000 rpm Ye s Ye s W albro CD Champion R CJ 7Y 0,02/0,5 W albro WT 1,06/0,5 12,6/5,7 (LD 13,2/6,0.
English – 21 TECHNICAL D A T A 240L 2,21/36,3 1,50/38 1,26/32 11 000-11 700 2 700 10 000 1,3 kW/ 9 000 rpm Ye s Ye s W albro CD Champion R CJ 7Y 0,02/0,5 W albro WT 1,06/0,5 13,9/6,3 98/101 106/106 4,0/3,8 4,2/4,4 6,4/7,4 6,7/11,0 T echnical data Engine C ylinder capacity , cu.
22 – English Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (U.S. Environmental P rotection Agency), CARB (California Air Resources Boar d) and H usqvarna F orest & Garden are pleased to explain the emissions contr ol system warranty on your 1999 and later small off-road engine.
English – 23 NO TES.
1998W51 ´*2§)¶5m¨.
An important point after buying a device Husqvarna 227L/LD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 227L/LD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 227L/LD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 227L/LD you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 227L/LD will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 227L/LD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 227L/LD.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 227L/LD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 227L/LD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
