Instruction/ maintenance manual of the product 2000 Husqvarna
Go to page of 17
HUSQV ARNA CONSTRUCTION PR ODUCTS Soff-Cut 2000 Please read the operator’ s manual carefully and make sur e you understand the instructions before using the machine.
CONTENTS Content Page T able of contents ………………………….. 2 Unpacking .................................................. 2 T ransporting ............................................... 2 Sound Data .....................................
INTRODUCTION Common sense: The focus of this manual is HOW to operate and service the equipment safely . It is not possible to cover every conceivable situation you can face when using this equipment. Therefore use this product only in a manner described in this manual.
4 REGISTER THE PRODUCT Please register your new 2000 with Husqvarna Construction Products by mailing in the registration card that came with the machine or you can register on the internet site www .husqvarnawarranty .com Registration will allow us to contact in case of any critical updates or recalls on this machine.
5 SAFETY W ARNINGS W ARNING Failure to comply with the following warnings could result in serious bodily injury or death! PERSONAL SAFETY • Read and understand instructions before operating saw . • Always wear safety approved hearing, eye, head and respiratory protection.
6 EXCEL SERIES BLADES The Excel Series of diamond blades have been designed specically for the Soff-Cut Ultra Early Entry dry cutting system of green concrete. These specialty blades are designed to increase speed and life while cutting a wide range of aggregates.
WHA T IS WHA T H E What is what? A. Oil ll & dipstick B. Air cleaner C. Recoil starter D. Fuel shut of f lever E. Choke lever F . Oil drain hose G. Fuel cap H. Fuel tank I. T ransmission oil ll cap J. Hour meter/T achometer K. Battery box L.
8 OPERA TING INSTRUCTIONS Experience is very important when running the 2000 saw . A skilled worker is highly recommended. Always do an inspec- tion of the saw before starting the engine. Check the fuel (H) and oil level (A) per the enclosed engine manual.
9 FUEL HANDLING PROPER FUEL T aking the following precautions will lessen the risk of injury and property damage: - Use extreme care in handling gasoline. It is extremely ammable and the vapors are explosive. - Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
10 Engine Oil Checking, Adding and Changing Oil Check the engine oil level (B) daily with saw fully lowered and the engine level. See the enclosed Robin manual for more details. Use SAE 10W-30 viscosity detergent automotive type with API service class SE or higher grade oil.
11 OTHER MAINTENANCE Guards Check all guards for damage and proper function daily espe- cially the blade block. Blade block and cover should be secure to the saw and not damaged.
12 As concrete hydrates or cures and begins to set, it develops internal stresses which may cause random cracks. Random cracks cast doubt on the quality and workmanship of the concrete. Contraction joints are cut in concrete to relieve these stresses before they seek their own relief in the form of random crack.
13 “ The timing of concrete operations - especially nishing and jointing - is critical” , states a quote from the foreword of the American Concrete Institute (ACI) 302.1 R-96. It goes on to say that “Failure to address this issue can contribute to unde- sirable characteristics in the wearing surface as cracking.
14 TROUBLESHOOTING ENGINE RUNS ROUGH, BACK FIRES OR CAN NOT REACH FULL SPEED - Check if there is fuel in the tank and it is the correct fuel. Make sure there is no water in the fuel. - Check that the spark plugs are clean and properly gapped. - Check that choke is in the “off” position after engine is warm.
TECHNICAL SPECIFICA TIONS Engine Model Robin EX 27 Engine oil volume, quarts/liters 1.0/1.0 Gasoline tank volume, gal/liters 1.6/6.1 T ype Air cooled, 4-cycle, single slant cylinder , overhead camshaf.
16 W ARRANTY HUSQV ARNA EQUIPMENT W ARRANTY New 2000 sold by Husqvarna Construction Products are warranted to be free from manufacturing defects in nor- mal service for a period of six (6) months for labor and up to one (1) year on parts from date of purchase by the original consumer purchaser or date of introduction into rental company eet.
1 153477-95 2009-12-29 w ww .hu sqvarnacp .com ´®z+UOo¶5N¨ ´®z+UOo¶5N¨ Original instructions.
An important point after buying a device Husqvarna 2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 2000 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 2000.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
