Instruction/ maintenance manual of the product 1152450-26 Husqvarna
Go to page of 20
E E E E n n n n g g g g l l l l i i i i s s s s h h h h K3000 K3000 W et Oper ator ′ s manual Please read the operator’ s manual car efully and mak e sure y ou understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols on the machine: W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ..........................................
4 – English WHA T IS WHA T? What is what on the power cutter - K3000? 1 2 3 4 5 6 7 8 10 11 12 14 15 9 6 13 1 Rear handle 2 Guard f or the blade 14” 3 Cutting blade 4 Locking the axle 5 F ront han.
English – 5 WHA T IS WHA T? What is what on the power cutter - K3000 W et? 1 Rear handle 2 Guard f or the blade 3 W ater kit 4 Cutting blade 5 Locking the axle 6 F ront handle 7 Inspection cov ers 8.
6 – English SAFETY INSTR UCTIONS Steps before using a ne w power cutter • Please read the operator’ s manual carefully and make sure you understand the instructions bef ore using the machine. • The machine is only designed f or cutting hard materials, such as concrete, brick, masonry as well as cast iron and cement pipes.
English – 7 SAFETY INSTR UCTIONS General safety warnings Sav e all warnings and instructions for future ref erence. The term ”power tool” in the warnings refers to y our mains- operated (corded) pow er tool or batter y-operated (cordless) power tool.
8 – English SAFETY INSTR UCTIONS P ersonal saf ety • Sta y aler t, watch what you are doing and use common sense when operaing a pow er tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating pow er tools may result in serious personal injur y .
English – 9 SAFETY INSTR UCTIONS Machine ′′ ′ ′ s safety equipment This section describes the machine ′ s safety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine .
10 – English SAFETY INSTR UCTIONS Cutting blades General • Cutting blades are a vailab le in two basic designs; abrasiv e discs and diamond blades .
English – 11 SAFETY INSTR UCTIONS Diamond blades Diamond blades consist of a steel body pro vided with segments that contain industrial diamonds. Diamond blades ensure lo wer costs per cutting operation, f ewer b lade changes and a constant cutting depth.
12 – English SAFETY INSTR UCTIONS General working instructions Cutting technique The technique described below is of a general character . Check inf or mation for each b lade regarding individual cutting characteristics (for e xample, diamond blades requires less f eeding pressure than an abrasive discs).
English – 13 SAFETY INSTR UCTIONS General rules • Ne ver start to cut with the upper quadrant of the blade as shown in the figure , also known as the kickbac k zone . • Alwa ys hold the machine in a firm grip with both hands. Hold it so that the thumbs and fingers grip round the handles.
14 – English ASSEMBL Y Assemb ly Fitting the cutting blade Husqvarna’ s blades are approv ed for hand-held po wer cutters. Blades are manuf actured with three diff erent diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1").
English – 15 ST AR TING AND ST OPPING Bef ore star ting K3000 We t W ater connector • Connect the water hose to the w ater supply (A). The water is s witched on and off with the water tap (B). Star ting • Grip the front handle with the left hand.
16 – English MAINTENANCE General Cleaning Cooling system The machine is equipped with an efficient f an to cool the motor . Cooling air which is drawn in through the g rille by the machines rear handle passes ov er the stator and rotor and out through the front of the motor housing.
English – 17 MAINTENANCE Bevel gear The grease in the gear housing should be changed e very 4 months. Use high quality gear grease The gear housing must not be filled completely with grease . The grease e xpands as the machine heats up during operation.
18 – English TECHNICAL D A T A ´®z+TM"¶6}¨ ´®z+TM"¶6}¨ Note 1: Handle vibrations are measured according to ISO 8662-4 Cutting equipment Max.
English – 19 TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the pow.
´®z+TM"¶6}¨ 2009-05-05 ´®z+TM"¶6}¨ 1152450-26.
An important point after buying a device Husqvarna 1152450-26 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 1152450-26 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 1152450-26 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 1152450-26 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 1152450-26 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 1152450-26, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 1152450-26.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 1152450-26. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 1152450-26 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
