Instruction/ maintenance manual of the product FP2205 Husky
Go to page of 24
precautions must be observed at all times: 1. Read all manuals included with this product carefully. Be thoroughly familiar with the controls and the proper use of the equipment. 2 . Follow all local electrical and safety codes as well as in the US, National Electrical Codes (NEC) and Occupational Safety and Health Act (OSHA).
23 Sp Guía de Diagnóstico de A verías (Continuación) Problema Posible(s) Causa(s) Acci ó n a tomar 1. Exceso de agua en el tanque 2. Humedad alta 1. El presostato está dañado 2. Consumo excesivo de aire 1. Condensación excesiva en el tanque 2.
FP2205 Series 3 Installation (Cont.) It is extremely important to install the compressor in a clean, well ventilated area where the surrounding air temperature will not be more than 100°F. A minimum clearance of 18 inches between the compressor and a wall is required because objects could obstruct air flow.
ASME SAFETY VALVE Do not remove or attempt to adjust the safety valve! This valve should be checked occasionally by pulling the ring by hand. Air may leak even after ring has been released.
5 Maintenance The compressor should be checked often for any visible problems and the following maintenance procedures should be performed each time the compressor is used. 1. Pull ring on safety valve and allow it to snap back to normal position. Safety valve must be replaced if it cannot be actuated or it leaks air after ring is released.
producto. 2. Si necesita reparar o reemplazar el cordón o el enchufe, no conecte el cable de conexión a tierra a ninguno de los terminales planos. El alambre cuya superficie externa del aislante es verde, con o sin rayas amarillas, es el cable de conexión a tierra.
7 T roubleshooting Chart (Continued) Symptom Possible Cause(s) Corrective Action 1. Excessive water in tank 2. High humidity 1. Defective pressure switch 2. Excessive air usage 1. Excessive condensation in tank 2. Air leaks in piping (on machine or in outside system) 3.
Informaciones Generales de Seguridad Como el compresor de aire y otros componentes usados (cabezales, pistolas pulverizadoras, filtros, lubricadores, mangueras, etc.), forman parte de un sistema de bombeo de alta presión, deberá seguir las siguientes medidas de seguridad todo el tiempo: 1.
système de haute pression, il est nécessaire de suivre les précautions suivantes: 1. Lire attentivement tous manuels compris avec ce produit. Se familiariser avec ce produit, ses commandes et son utilisation.
15 Fr Guide de D é pannage (Suite) Sympt ô me Cause(s) Possible(s) Mesures Correctives 1. Eau excessive dans le réservoir 2. Humidité élevée 1. Manostat défectueux 2. Utilisation d’air excessive 1. Condensation excessive dans le réservoir 2.
correctement en respectant tous les codes et règlements locaux. L ’ usage incorrect d ’ une fiche de mise à la terre peut r é sulter en secousse é lectrique! Ne pas utiliser un adaptateur de mise à la terre avec ce produit! 2.
7. Ajuster le régulateur à la bonne pression (outil ou pneu). Utiliser l’outil conformément aux instructions. Le compresseur se remettra automatiquement en marche lorsque la pression du réservoir tombe sous la pression d’enclenchement.
7. Ajuster le régulateur à la bonne pression (outil ou pneu). Utiliser l’outil conformément aux instructions. Le compresseur se remettra automatiquement en marche lorsque la pression du réservoir tombe sous la pression d’enclenchement.
correctement en respectant tous les codes et règlements locaux. L ’ usage incorrect d ’ une fiche de mise à la terre peut r é sulter en secousse é lectrique! Ne pas utiliser un adaptateur de mise à la terre avec ce produit! 2.
15 Fr Guide de D é pannage (Suite) Sympt ô me Cause(s) Possible(s) Mesures Correctives 1. Eau excessive dans le réservoir 2. Humidité élevée 1. Manostat défectueux 2. Utilisation d’air excessive 1. Condensation excessive dans le réservoir 2.
système de haute pression, il est nécessaire de suivre les précautions suivantes: 1. Lire attentivement tous manuels compris avec ce produit. Se familiariser avec ce produit, ses commandes et son utilisation.
Informaciones Generales de Seguridad Como el compresor de aire y otros componentes usados (cabezales, pistolas pulverizadoras, filtros, lubricadores, mangueras, etc.), forman parte de un sistema de bombeo de alta presión, deberá seguir las siguientes medidas de seguridad todo el tiempo: 1.
7 T roubleshooting Chart (Continued) Symptom Possible Cause(s) Corrective Action 1. Excessive water in tank 2. High humidity 1. Defective pressure switch 2. Excessive air usage 1. Excessive condensation in tank 2. Air leaks in piping (on machine or in outside system) 3.
producto. 2. Si necesita reparar o reemplazar el cordón o el enchufe, no conecte el cable de conexión a tierra a ninguno de los terminales planos. El alambre cuya superficie externa del aislante es verde, con o sin rayas amarillas, es el cable de conexión a tierra.
5 Maintenance The compressor should be checked often for any visible problems and the following maintenance procedures should be performed each time the compressor is used. 1. Pull ring on safety valve and allow it to snap back to normal position. Safety valve must be replaced if it cannot be actuated or it leaks air after ring is released.
ASME SAFETY VALVE Do not remove or attempt to adjust the safety valve! This valve should be checked occasionally by pulling the ring by hand. Air may leak even after ring has been released.
FP2205 Series 3 Installation (Cont.) It is extremely important to install the compressor in a clean, well ventilated area where the surrounding air temperature will not be more than 100°F. A minimum clearance of 18 inches between the compressor and a wall is required because objects could obstruct air flow.
23 Sp Guía de Diagnóstico de A verías (Continuación) Problema Posible(s) Causa(s) Acci ó n a tomar 1. Exceso de agua en el tanque 2. Humedad alta 1. El presostato está dañado 2. Consumo excesivo de aire 1. Condensación excesiva en el tanque 2.
precautions must be observed at all times: 1. Read all manuals included with this product carefully. Be thoroughly familiar with the controls and the proper use of the equipment. 2 . Follow all local electrical and safety codes as well as in the US, National Electrical Codes (NEC) and Occupational Safety and Health Act (OSHA).
An important point after buying a device Husky FP2205 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husky FP2205 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husky FP2205 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husky FP2205 you will learn all the available features of the product, as well as information on its operation. The information that you get Husky FP2205 will certainly help you make a decision on the purchase.
If you already are a holder of Husky FP2205, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husky FP2205.
However, one of the most important roles played by the user manual is to help in solving problems with Husky FP2205. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husky FP2205 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
