Instruction/ maintenance manual of the product MB519-01 Hunter Fan
Go to page of 19
MB519-01 • 03/13/15 • © Hunter F an Company www .HunterF anInternational.com ENGLISH.
Befor e installation and usage of this produc t, please read this manual and keep it for future ref erence ..
www .HunterF anInternational.com PA G E 12 PA G E 5 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Maintenanc e & Cleaning T rouble.
www .HunterF anInternational.com MB519-01 • 03/13/15 • © Hunter F an Company What t o Expec t with Y our Installation 2 Know your wiring If you are unfamiliar with wiring , use a qualied electrician.
www .HunterF anInternational.com T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools .
www .HunterF anInternational.com If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) .
www .HunterF anInternational.com C eiling Bracket Refer to warning w .1 on pg. 2 T o avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
6 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 3 m (10’) or higher Shorter Downrod for fans installed close to ceiling Standard .
7 KEEP! 20 cm (8”) 1 cm (3/8”) C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od.
www .HunterF anInternational.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball int o the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canopy sit loosely on t op of the fan.
www .HunterF anInternational.com Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/yello w stripe, or bare c opper) coming from the ceiling , downrod , and hanging bracket.
www .HunterF anInternational.com Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts int o the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardware bag .
www .HunterF anInternational.com Blades 11 Put the blade washers , found in the hardware bag , onto the blade screws, f ound in the hardware bag. T hen install the blade screws to secure each blade to a blade ir on.
www .HunterF anInternational.com Make sure the upper switch housing is securely attached to the mounting plate. F ailure to properly secure all 3 assembly screws could result in the switch housing xture falling.
13 Light Kit Partially install two of the light kit assembly screws, f ound in the hardware bag, into the upper switch housing . Lif t the light kit assembly and connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors.
14 Install a CFL bulb into each of the sockets. When necessary , replace with bulbs of the same type and wattage. Lift the inner glass ush against the metal plate and install the globe keeper . Thread the pull chains through the holes in the nial cap .
www .HunterF anInternational.com Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! See next page for fan opera tion instruc tions. T o attach the outer glass, install the thumbscrews and tighten securely . Connect the appropriate pull chain pendant to each of the short chains.
www .HunterF anInternational.com Maintenanc e & Cleaning ON T urn Po wer Changing the direction of air ow - unscrew the nial and remov e it from the threaded rod . Remove the nial cap and unscrew the globe keeper while supporting the inner glass with your other hand .
www .HunterF anInternational.com T roubleshooting Exc essive w obbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , suppor t the fan carefully , and check that the hanger ball is properly seated . • Use the provided balancing kit and instruc tions to balance the fan.
An important point after buying a device Hunter Fan MB519-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Fan MB519-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Fan MB519-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Fan MB519-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Fan MB519-01 will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Fan MB519-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Fan MB519-01.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Fan MB519-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Fan MB519-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
