Instruction/ maintenance manual of the product M3535-01 Hunter Fan
Go to page of 19
www .HunterF an.com 1.888.830.1326 PA G E 13 Light Kit PA G E 12 Blades T able of C ontents Operation, Maintenanc e & Cleaning PA G E 17 T roubleshooting ? ? ? PA G E 19 PA G E 5 Ceiling Br acket .
www .HunterF an.com 1.888.830.1326 M3535-01 • 06/18/13 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you.
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools .
www .HunterF an.com 1.888.830.1326 4 M3535-01 • 06/18/13 • © Hunter F an Company 1.866.268.1936 If you ha ve an angled ceiling: 1. Y ou will need a longer do wnrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) .
www .HunterF an.com 1.888.830.1326 C eiling Bracket 5 Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
www .HunterF an.com 1.888.830.1326 Assembling the T op Housing KEEP! Remove the pre-installed setscrew so that the downrod can be inserted. K E E P ! Install three upper motor co ver screws, f ound in the hardware bag , and tighten them securely .
www .HunterF an.com 1.888.830.1326 7 M3535-01 • 06/18/13 • © Hunter F an Company 1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 skip to next page If you need a diff erent downrod length follo w these steps: Steps 1-5 to remo ve standard downrod pipe Steps 6-10 to reassemble with new pipe www .
www .HunterF an.com 1.888.830.1326 Downrod (c ontinued) 8” 3/8” If the setscrew is not tightened securely , the fan may fall. 1.888.830.1326 www .HunterF an.com 8” 3/8” C U T & S T R I P (not to scale) The wires can be cut, but lea ve at least 8” extending from the top of the downrod .
1.888.830.1326 9 M3535-01 • 06/18/13 • © Hunter F an Company www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy .
www .HunterF an.com 1.888.830.1326 Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x.
www .HunterF an.com 1.888.830.1326 11 M3535-01 • 06/18/13 • © Hunter F an Company Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown.
www .HunterF an.com 1.888.830.1326 Blades Y our blades ar e shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes.
www .HunterF an.com 1.888.830.1326 Light Kit Align the keyholes in the light k it with the two partially installed screws and turn the light k it clockwise until the screws are in the narrow ends of the keyholes. Thread the 9-pin plug connector from the fan through the light kit.
www .HunterF an.com 1.888.830.1326 14 M3535-01 • 06/18/13 • © Hunter F an Company Light Kit (c ontinued) Make sure the light kit is securely attached to the mounting plate. F ailure to properly secure all thr ee assembly screws could result in the light xture falling.
www .HunterF an.com 1.888.830.1326 15 M3535-01 • 06/18/13 • © Hunter F an Company Light Kit (c ontinued) Connect the 4 pin plug from the ballast to the uorescent bulb. 4 Pin Plug C ONGRA TULA TIONS! Y OU’RE DONE! See next page for fan opera tion instruc tions.
www .HunterF an.com 1.888.830.1326 Remote C ontrol ON T urn P ow er Note: The remote must be pair ed before the fan will operate. Within 3 minutes of rest oring power to the fan, press both the F an Off button and the High button for at least 4 seconds .
www .HunterF an.com 1.888.830.1326 Rocker- Style Plate Switch C over Plate Removed T abs T o install the tr ansmitter cradle, remov e the two screws holding the switch c over plate. Do not remov e the cover plate. Orient the cr adle by lining up the two mounting holes with those on the cov er plate.
www .HunterF an.com 1.888.830.1326 18 M3535-01 • 06/18/13 • © Hunter F an Company Opera tion, Maintenance , & Cleaning (con tinued) When cleaning the fan, use soft brushes or cloths to prevent scr atching. Cleaning products may damage the nishes.
www .HunterF an.com 1.888.830.1326 M3535-01 • 06/18/13 • © Hunter F an Company 19 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • Use the provided balancing kit and instruc tions to balance the fan.
An important point after buying a device Hunter Fan M3535-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Fan M3535-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Fan M3535-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Fan M3535-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Fan M3535-01 will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Fan M3535-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Fan M3535-01.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Fan M3535-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Fan M3535-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
