Instruction/ maintenance manual of the product M0028-01 Hunter Fan
Go to page of 14
www .HunterF an.com 1.888.830.1326 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed PA G E 6 Hanging the F an PA G E 8 Motor Housing T ab.
www .HunterF an.com 1.888.830.1326 M0028-01 • 06/25/15 • © 2012–2015 Hunter F an Company What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you .
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers If mounting to a support structure, you will also need these tools .
www .HunterF an.com 1.888.830.1326 4 M0028-01 • 06/25/15 • © 2012–2015 Hunter F an Company C eiling Bracket OFF Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing y our fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
www .HunterF an.com 1.888.830.1326 C eiling Bracket (c ontinued) Prepar ation 1.888.830.1326 www .HunterF an.com Time Sav er Tip: Get a helper to insert grommets, found in the hardware bag , into the blades while you ’r e doing the next couple of steps.
www .HunterF an.com 1.888.830.1326 Hanging the F an While holding the wires out of the way , lif t the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket.
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , fan, and hanging bracket.
www .HunterF an.com 1.888.830.1326 With a Phillips head screwdriv er , install the four motor housing screws f ound in the hardware bag . Tighten all four screws securely . Motor Housing Screw Holes Motor Housing Screw Indentation Notch Raise the motor housing up over the motor and ceiling bracket.
www .HunterF an.com 1.888.830.1326 Blades Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardw are bag. Lightly attach the blade irons to the motor with screws found in the hardware bag , then securely tighten after both screws are attached .
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two housing assembly screws from the hardware bag halfwa y into the motor housing .
www .HunterF an.com 1.888.830.1326 11 M0028-01 • 06/25/15 • © 2012–2015 Hunter F an Company Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. F ailure to properly secur e all three assembly screws could result in the light xture falling.
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions. Connect the appropriate pull chain pendant to each of the short chains coming from the nial and nial cap .
www .HunterF an.com 1.888.830.1326 Maintenanc e, Oper ation & Cleaning Cleaning the fan - use soft brushes or cloths to prevent scratching . Cleaning products may damage the nishes. Changing the bulbs - unscrew the nial and remove it from the threaded rod .
www .HunterF an.com 1.888.830.1326 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • Use the provided balancing kit and instruc tions to balance the fan. Noisy Operation • Tighten the blade and blade iron screws until they are snug .
An important point after buying a device Hunter Fan M0028-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Fan M0028-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Fan M0028-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Fan M0028-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Fan M0028-01 will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Fan M0028-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Fan M0028-01.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Fan M0028-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Fan M0028-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
