Instruction/ maintenance manual of the product M0006-01 Hunter Fan
Go to page of 15
www .HunterF an.com 1.888.830.1326 PA G E 5 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed T able of C ontents PA G E 12 PA G E 15 Main.
www .HunterF an.com 1.888.830.1326 M0006-01 • 04/14/14 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you .
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools .
www .HunterF an.com 1.888.830.1326 If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) .
www .HunterF an.com 1.888.830.1326 C eiling Bracket OFF F or angled ceilings, point opening toward peak. Refer to warning w .1 on pg. 2 If you are unable to do this, call T echnical Support at 1-888-830-1326. Use wood scr ews (included) when securing to support struc ture with approved electrical outlet box.
www .HunterF an.com 1.888.830.1326 6 M0006-01 • 04/14/14 • © Hunter F an Company Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings.
www .HunterF an.com 1.888.830.1326 7 M0006-01 • 04/14/14 • © Hunter F an Company KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops.
www .HunterF an.com 1.888.830.1326 Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan.
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket.
www .HunterF an.com 1.888.830.1326 Canop y Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. No te: Fan style may vary . Lift the canopy into place so that the screw holes are aligned . Screw Holes Insert the two canopy screws found in the hardwar e bag.
www .HunterF an.com 1.888.830.1326 Blades Align the three holes in the blade with the three blade iron posts. Squeeze the blade and the blade post together . The ared tops of the blade iron posts will be fully visible above the blade when properly assembled .
www .HunterF an.com 1.888.830.1326 12 M0006-01 • 04/14/14 • © Hunter F an Company Partially install two of the switch housing screws found in the bag . Connect the plugs from the upper and lower swit ch housings. Make sure to line up the colored markings on the connec tors.
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions. Connect a pull chain pendant to each of the short chains coming from the switch housing .
www .HunterF an.com 1.888.830.1326 Maintenanc e & Cleaning ON T urn P ower F or cleaning the fan, use sof t brushes or cloths to prevent scratching . Cleaning products may damage the nishes. T o switch the direc tion of air ow , mov e the reverse switch to the opposite position.
www .HunterF an.com 1.888.830.1326 T roubleshooting Exc essive wobbling • Make sure that the blades are properly installed on the blade iron posts. • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated .
An important point after buying a device Hunter Fan M0006-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Fan M0006-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Fan M0006-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Fan M0006-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Fan M0006-01 will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Fan M0006-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Fan M0006-01.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Fan M0006-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Fan M0006-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
