Instruction/ maintenance manual of the product 22360 Hunter Fan
Go to page of 8
1 41556-01 8/08/03 © 2003 HUNTER FAN CO. SINCE 1 8 8 6 ® INST ALLA TION INSTRUCTIONS FOR HUNTER ORIGINAL ® CEILING F ANS ! W ARNINGS ! • T o avoid possible electrical shock, before wir- ing fan, disconnect power by turning off the cir- cuit breakers both to the outlet box and to its associated wall switch location.
© 2003 HUNTER FAN CO. 41556-01 8/08/03 2 S tep 2: Inspect the Fan 1. Unpack the fan carefully to avoid any damage to components. Figure 2 ! CAUTION ! • Never lift the motor by the wires. Let the motor rest in the carton liner for protection. 2. Check the sack parts.
3 41556-01 8/08/03 © 2003 HUNTER FAN CO. S tep 3: Installation of Ceiling Mounting Hardwar e 2” x 4” W ood Brace Outlet Box Ceiling Joist Ceiling M4 W ood Screw & W asher (2) Required Figure 3 2. Drill two (2) 1/4” diameter holes 2-9/16” apart through the back of the outlet box into the cross brace.
© 2003 HUNTER FAN CO. 41556-01 8/08/03 4 Set Screws Figure 5 3. Be sure the pin is center ed in the rubber bushing. See Figures 6 and 7. 4. Lift the fan by the motor housing and hook the hanger bracket onto the pin in the rubber bush- ing. Make sure both ends of the pin ar e outside the hanger bracket.
5 41556-01 8/08/03 © 2003 HUNTER FAN CO. S tep 6: Lubrication 1. Y our fan has been shipped without oil in the motor . A tube of high grade SAE 10 non-detergent oil is packed in the sack parts. All of the oil in the tube must be put into the fan. 2. Unscrew the oil hole screw on the side of the switch housing.
© 2003 HUNTER FAN CO. 41556-01 8/08/03 6 NOTE: Gr ommets ar e usually assembled by hand. If you use a tool, make certain you do not damage the gr ommet or blade when inserting the gr ommets. 4 . W ith some fans you have an option to install Figure 15 four or five blades.
7 41556-01 8/08/03 © 2003 HUNTER FAN CO. Lubrication Once properly installed, your fan needs little attention, beyond checking the oil level. The oil is checked by unscrewing and removing the oil hole screw . If oil comes out of the hole, the oil level is within proper levels.
© 2003 HUNTER FAN CO. 41556-01 8/08/03 8 TROUBLESHOOTING Nothing happens; fan does not move. Noisy operation. Excessive W obbling 1. Power turned off, fuse blown, or cir - cuit breaker tripped. 2. Loose wire connections or wrong connections. 3. Motor reversing switch not engaged.
An important point after buying a device Hunter Fan 22360 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Fan 22360 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Fan 22360 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Fan 22360 you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Fan 22360 will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Fan 22360, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Fan 22360.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Fan 22360. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Fan 22360 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
