Instruction/ maintenance manual of the product W19q HP (Hewlett-Packard)
Go to page of 32
w19b / w19e / W19q LCD Monitor User ’ s Guide • Preface • Safety and Maintenance Guidelin es • Setup • Using the Monitor • Installing Drivers and Using the Auto-Adjust ment Feature • T e.
Back to Contents Page Preface About This Guide • Notational Conven tions About This Guide This guide is intended for anyone who uses the w 19b / w19e / W19q LCD Monitor.
Back to Contents Page Safety and Maintenance Guidelines Important Safety Information • Safety Precautions • Maintenanc e Guidelines • Cleaning the Monitor Impor tant Safety Information The power cord is design ed for use with your monitor. To use a different cord, use only a power source and connection compatible wi th this monitor.
Maintenance Guidelines To enhance the performa nce and extend the life of your monitor: • Do not open your monitor cabinet or attempt to ser vice this product yourself . If your monitor is not operating properly or has been dropped or damaged, contact yo ur Hewlett-Packard authoriz ed dealer , reseller , or ser vice provider .
Back to Contents Page Setup Base and Tilt • Cables • Wall Mounting Arm Base and Tilt Attaching the Base • Removing th e Base • Adjusting the Ti lt Attaching the Base 1 Set the panel face-down on a flat, protected surface. 2 Align the pedestal slots with the panel tabs and insert ( A ).
Removing the Base 1 Push the release tab and raise the pedestal off the base. 2 Set the panel face-down on a flat, protected surface. 3 Slide the pedestal to the left to unlock it from the base ( A ). 4 Remove the pedestal from the panel ( B ). WARNING: Be careful to avoid pinching or scraping fingers when attaching the base.
Adjusting the Tilt For optimal viewing, adjust th e screen tilt to your own preference, as follow s: 1 Face the front of the monitor and hold the stand so that you do not topple the monitor while changin g the tilt. 2 Adjust the tilt by moving the monitor’ s top edge toward or away from yo u.
Back to Contents Page Cables Attaching the Cables Attaching the Cables You can attach a VGA cable (provided), a DVI-D cable (select m odels only), or both to th is monitor. To us e DVI, your computer must have a DVI-compliant graphics card . Conn ectors are found on th e back of the mo nitor.
3 If you are attaching a VGA cable, co nnect one end of the 15-pin D-Sub VGA cable (blu e connector) to the back of the monitor and connect the other end to th e computer VGA por t.
5 Connec t one end of th e power cord to the back of t he monitor and plug th e other end into a grounded outlet. 6 Secure the cables by routin g them through the cla sp. 7 T urn on your monitor and computer . If your monitor displays an image, installation is complete.
Back to Contents Page W all Mounting Arm Preparing to Install An Optional Wall Mounting Arm (Not supplied) • Installing a Wall Mounting Arm Preparing to Install a W all Mo unting Arm (Not supplied) This monitor can be attached to a wall mounting arm that you purchase sepa rately.
Back to Contents Page Using the Monitor Operating Instructions • External Cont rols • LED Indicators • Settings • Setting the Opti mal Resolution • Adjusting the Volume • Using Headphones .
External Controls A AUTO-configuration / Exit B Volume decrease / Left na vigation C Power D Volume increase / Right navigatio n E MENU / Enter F Headphone jack LED Indicators Status LED Color Full Power Mode Green Active-off Mode Orange See Technical Support FAQs for more infor mation.
Back to Contents Page Settings Setting the Op timal Resolution • Adjusting th e Volume • Using Headphones • Locking the OSD • Adjusting OSD Settings • OSD Menu Setting the Optimal Resolution The recommended resoluti on for this monitor is 1440 by 900.
Adjusting OSD Setti ngs 1 Press the MENU button to activat e the OSD menu. 2 Press or to navigate through the functions. Once the de sired function is highlighted, press the MENU button again to activate it. If the selecte d func tion has a sub-m enu, it will be displayed.
Main Menu Item Main Menu Icon Sub-Menu Item Sub-Menu Icon Description H. Position Adjust the horizontal posit ion of the picture Image Position V. P o s i t i o n Adjust the vertical position of the p.
Back to Contents Page Installing Drivers and Using the Auto-Adjustment Feature Downloading Drivers and Software To download the latest version of drivers and so ftware files fro m the HP Support Web si te: 1 Refer to: http://www .hp .com/suppor t 2 Select your countr y/region.
Back to Contents Page T echnical Suppor t F AQs T echnical Suppor t F AQs (Frequently Asked Questions) Problem & Question Possible Solutions Power LED is not on • Make sure the powe r button is on and the power cord is properly connected to a grounded power ou tlet and to the m onitor .
Problem & Question Possible Solutions Missing one of the pri mary colors (red, green, or blue) • Inspect the monitor’ s video cable and make sure that none of the pins are bent. • Make sure the monitor’ s video cabl e is properly connected to the computer .
Back to Contents Page Specifications General • LCD Panel (19" ) • Resolution • Preset Display Modes • Physical Characteristics • Environmental • Power Cord Set Requirements • Pin As.
Preset Display Modes Standard Resolution Horizontal Frequency (kHz) V ertical Frequency (Hz) Dos-mode 720 x 400 31.47 70.0 VGA 640 x 480 31.47 60.0 VGA 640 x 480 37.50 75.0 SVGA 800 x 600 37.879 60.0 SVGA 800 x 600 46.875 75.0 XGA 1024 x 768 48.363 60.
Power Cord Set Requirements The monitor power supply is provided with automatic line switching (AL S). This feature allows the monitor to operate on input voltages in the range of 100–240V , 50/60 Hz, 1.
Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 TMDS Data 2– 9 TMDS Data 1– 17 TMDS Data 0– 2 TMDS Data 2+ 10 TMDS Data 1+ 18 TMDS Data 0+ 3 TMDS Data 2/4 Shield 11 TMDS Data 1/3 S.
Back to Contents Page LCD Monitor Quality and Pixel Policy The HP LCD Monitor uses high-preci sion technolog y, manufactured according to high standards, to he lp guarantee trouble-free performance. Ne vertheless, th e display may have cosm etic imperfections tha t appear as small bright or dark spots.
Back to Contents Page Agency Regulator y Notices Federal Communications Commission Notice This equipment has b een tested and found to compl y with the limits for a Class B digital device, pursuant to Part 15 of the FCC R ules. These limits are designed to provid e reasonable protection agains t harmful interference in a residential installation.
Declaration of Conformity for Pr oducts Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rul es. Oper ation is subject to the following two condition s: (1) this d.
Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interf erence-Causing Equipment Regulations. Av i s C a n a d i e n Cet appareil numérique de la classe B re specte toutes les exigen ces du Règlement sur le matériel brouilleur du Canada.
Disposal of W aste Equipment by Us ers in Private Households in the European Union This symbol on the product or on its p ackaging indicates th at this product must not be disposed of with your other household waste.
Japanese Power Cord Notice Japanese Material Content Declaration A Japanese regulatory requirement, define d by Specification JIS C 0950, 2005, mandates that manufacturers provide Mate rial Content Declarat ions for certain categories of electronic products offered for sale aft er July 1, 2006.
HP Recycling Program HP offers product end-of-life return programs for HP an d other manufacturers’ hardware in several geographic areas. The terms and availability of these programs vary by geography because of di fferences in regulatory requirements and local customer d emand .
Congratulations! The display you have just purchased c a rries the TCO’03 Display label. This means that your display is designed, manufactured and tested according to some of the strictest q uality and environmental requirem ents in the world.
Ecology • The product is prepared for recycling and the manufact urer must have a cer tified environ mental management system such as EMAS or ISO 14 001. • Restrictions on: • chlorinated and brominated fl ame retardants and polymers • heavy metals such as cadmium, mercur y and lead.
An important point after buying a device HP (Hewlett-Packard) W19q (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought HP (Hewlett-Packard) W19q yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data HP (Hewlett-Packard) W19q - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, HP (Hewlett-Packard) W19q you will learn all the available features of the product, as well as information on its operation. The information that you get HP (Hewlett-Packard) W19q will certainly help you make a decision on the purchase.
If you already are a holder of HP (Hewlett-Packard) W19q, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime HP (Hewlett-Packard) W19q.
However, one of the most important roles played by the user manual is to help in solving problems with HP (Hewlett-Packard) W19q. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device HP (Hewlett-Packard) W19q along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
