Instruction/ maintenance manual of the product FSPCI64S HP (Hewlett-Packard)
Go to page of 20
FuturePlus Systems Corporation LOCAL BUS PCI Scope Preprocessor Users Manual-FSPCI64S For Hewlett-Packard Logic Analysis Systems Revision 1.0 FuturePlus Systems and PCI Scope is a trademark of FutureP.
2 HOW TO REACH US 4 PRODUCT WARRANTY 5 Limitation of warranty 5 Exclusive Remedies 5 Assistance 6 INTRODUCTION 7 How to Use This Manual 7 ANALYZING THE PCI LOCAL BUS 8 Duplicating the Master Diskette .
3 Standards Supported 15 Power Requirements 15 MultiProbe Pods required 15 Signal loading 15 Operations 16 Environmental Temperature 16 Altitude 16 Humidity 16 Testing and Troubleshooting 16 Servicing.
4 How to reach us FuturePlus Systems can be reached at: FuturePlus Systems Corporation 36 Olde English Road Bedford, NH 03110 TEL:603-471-2734 FAX:603-471-2738 Internet: 71035.3052@compuserve.com WEB:www.futureplus.com FuturePlus Systems is represented in Japan by: ANDOR Systems Support Co.
5 Product Warrant y This FuturePlus Systems product has a warranty against defects in material and workmanship for a period of 1 year from the date of shipment. During the warranty period, FuturePlus Systems will, at its option, either replace or repair products proven to be defective.
6 SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY. Product maintenance agreements and other customer assistance agreements are available for FuturePlus Systems products.
7 Introduction The PCI Scope Preprocessor module provides a complete interface between any PCI add-in slot and the HP MultiProbe system. The Preprocessor interface connects the signals from the PCI Local bus to the inputs of a 208 PQFP package used as the MultiProbe connection point.
8 Analyzing the PCI Local Bus This chapter introduces you to the PCI Scope Preprocessor and lists the minimum equipment required and accessories supplied for PCI Local Bus analysis. Before you use the PCI Preprocessor software, make a duplicate copy of the master diskette.
9 • An Oscilloscope • The PCI Scope Preprocessor Product • A PCI target bus This operating manual uses the same signal notation as the PCI LOCAL BUS SPECIFICATION - REVISION 2.1. That is, a # symbol at the end of a signal name indicates that the signal’s active state occurs when it is at a low voltage.
10 PCI_MUL.DUT and PCI.ADP from your PCI Scope Preprocessor diskette to that directory. 3. Access the configuration menu of the MultiProbe Control card. 4. Select POD setup for the POD that will be connected to the Scope Preprocessor. 5. On the next menu select #2 Specify POD adapter and then select the file PCI.
11 Analog Analysis Since the PCI Scope Preprocessor interface contains only passive matching terminators it introduces negligible skew to the PCI Local Bus signals. The following procedure describes the major steps required to perform analog analysis measurements with the PCI Scope Preprocessor module.
12 Select the oscilloscope for each MultiProbe output using the Select Signals menu of the MultiProbe control module. 1. Access the Select Signals menu. 2. Select the scope for each output a) Choose the output (Output 1 or Output 2) of the control module that is connected to the pod that is attached to the PCI Scope Preprocessor.
13 Using an HP16534A oscilloscope If you are using an HP 16534A oscilloscope, then follow this procedure. 1. Access the oscilloscope menus. To view your measurements with an HP16534A oscilloscope, you need to exit the MultiProbe Control menus, then enter the oscilloscope menus.
14 When the PCI Personality Adapter 101 is not in use, keep it in its original container. The file PCI.ADP matches the configuration of the PCI Personality Adapter and configures the MultiProbe for PCI Analysis.
15 General Information This chapter provides additional reference information including the characteristics and signal connections for the PCI Scope Preprocessor module. The following operating characteristics are not specifications, but are typical operating characteristics for the PCI Scope Preprocessor module.
16 information on the electrical loading of the MultiProbe Pod refer to your Hewlett-Packard MultiProbe specification. All PCI Local Bus operations supported.
17 The below table shows the connection from the PCI Local Bus to the PQFP package that acts as the MultiProbe Contact point. If the pin is not listed it is Grounded.
18 AD26 75 AD25 77 AD24 79 C/BE3# 81 AD23 83 AD22 85 AD21 87 AD20 89 AD19 91 AD18 93 AD17 95 AD16 97 C/BE2# 99 FRAME# 101 IRDY# 103 TRDY# 105 DEVSEL# 107 STOP# 109 LOCK# 111 SDONE 113 PERR# 115 SBO# 1.
19 AD09 137 C/BE0# 139 AD08 141 AD07 143 AD06 145 AD05 147 AD04 149 AD03 151 AD02 153 AD01 155 AD00 157 ACK64# 159 REQ64# 161 C/BE7# 163 C/BE6# 165 C/BE5# 167 C/BE4# 169 PAR64 171 AD32 173 AD33 175 AD.
20 AD45 199 AD46 201 AD47 203 AD48 205 AD49 207.
An important point after buying a device HP (Hewlett-Packard) FSPCI64S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought HP (Hewlett-Packard) FSPCI64S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data HP (Hewlett-Packard) FSPCI64S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, HP (Hewlett-Packard) FSPCI64S you will learn all the available features of the product, as well as information on its operation. The information that you get HP (Hewlett-Packard) FSPCI64S will certainly help you make a decision on the purchase.
If you already are a holder of HP (Hewlett-Packard) FSPCI64S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime HP (Hewlett-Packard) FSPCI64S.
However, one of the most important roles played by the user manual is to help in solving problems with HP (Hewlett-Packard) FSPCI64S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device HP (Hewlett-Packard) FSPCI64S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
