Instruction/ maintenance manual of the product GF640 Hotpoint
Go to page of 16
Instructions for Installation and Use Gas Hob Model GF640 - GF 641.
2 CONTENTS Introduction For Your Safety Know your Hob How to use your Hob Practical Advice Care and Cleaning Troubleshooting Installation Electrical Connection Characteristics of Burners and Nozzels A.
3 Y our new hob is guaranteed* and will giv e lasting ser vice. This guarantee is only applicable if the appliance has been installed in accordance with the installation instructions detailed in this booklet. To help make best use of your cooking equipment, please read this booklet carefully.
4 For Y our Safety AL W A YS: - make sure you remove all packaging and dispose of saf ely . - check the soundness of the appliance after it has been unpacked. - make sure you understand the controls before using the appliance. - keep children away from the appliance during use.
5 D F A B C E A. Gas Burners B. Pan Support for Cookware C. Control Knobs for Gas Burners D. Ignitor for Gas Burners E. Ignition Button for Gas Burner s (only on cer tain models) F. Flame Failure Device - Activates if the flame accidentally goes out (spills, drafts, etc.
6 Practical Advise on Using the Burners For best performance, follow these general guidelines: • Use the appropriate cookware for each burner (see table) in order to prevent the flame from reaching .
7 Care and Cleaning Troubleshooting If the burner does not remain on when set to "Low". Check to make sure that: • The gas holes are not clogged. • There are no draughts near the cooking surface. • The minimum has been adjusted correctly (see Installation section, "Minimum Regulation").
8 Installation The following instructions are intended for the installer so that the installation and maintenance procedures may be followed in the most professional and expert manner possible. Important: Disconnect the appliance from the electrical suppl y before performing any maintenance or repair.
9 Gas Connection for the Hob The hob should be connected to the gas supply by an authorized installer. During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing.
10 Adapting the Hob for Different Types of Gas To adapt the hob to a different type of gas than that for which it was designed, (see the sticker under the hob or on the packaging), the burner nozzles must be changed, as follows: • Remove the pan supports and slide the burners out of the cooktop .
11 Electrical Connection Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED. The hob is designed to work with alternating current, the supply voltage and frequency indicated on the rating plate (situated under the hob). Make sure that the local supply voltage corresponds to the voltage indicated on the rating plate.
12 Characteristic of the burners and nozzles T a bl e 1 Liquid G a s N a tur a l G a s Burner Diameter (mm) Thermal P ower kW (p .c.s.*) By-pass 1/100 (mm) Noz zle 1/100 Flow* g/h Noz zle r 1/100 Flow* l/h Nom. Red . (1 ) (mm) *** ** (mm) Fa s t (Large) (R ) 100 3.
13 Notes.
GB 14 "No company is better positioned to offer an after sales service on a Hotpoint appliance than us - the manufacturer" As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months.
GB 15 Guarantee "Satisfaction guaranteed or your money back" We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or visit our web-site at www.
0 9 -200 5 P a r t n o . FP162 - 01 Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in both the appliances and services we offer. Repair Service and Information Desk UK: 08709 066 066 (Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays) www.
An important point after buying a device Hotpoint GF640 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hotpoint GF640 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hotpoint GF640 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hotpoint GF640 you will learn all the available features of the product, as well as information on its operation. The information that you get Hotpoint GF640 will certainly help you make a decision on the purchase.
If you already are a holder of Hotpoint GF640, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hotpoint GF640.
However, one of the most important roles played by the user manual is to help in solving problems with Hotpoint GF640. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hotpoint GF640 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
