Instruction/ maintenance manual of the product MODEL PCN90 Hobart
Go to page of 15
CONVECTION OVENS • MODEL PCN90 SERIES ELECTRIC CONVECTION OVENS peN90 ML-43719 HOBART} EXECUTIVE OFFiCES TROY, OHIO 45374 FORM 16842 Rev. A (4-90).
- THIS PAGE INTENTIONALLY LEFT BLANK -.
Installation, Operation and Care of PCN90 SERIES ELECTRIC CONVECTION OVENS SAVE THESE INSTRUCTIONS GENERAL The PCN90 Series electric convection ovens feature Perfect Touch™ programmable controls.
FRONT OF DEVICE • •• LOCAnNGSTUDS .0. ' . . BOTTOM :0: c:::==::J :0: ~ REAR OF DEVICE Fig. 1 - Installation of basic oven on cabinet - (procedures identical for installing open stand, CX286). Assembling Cabinet Base or Stand (PCN903) 1. Screw two loceuing studs (found in cabinet base or stand carton) into bottom of oven (Fig.
INSTALLING DOUBLE OVENS Assembling Stacked Ovens (PCN902) 1. Position one oven on its back for access to the oven bottom, taking care not to scratch the sides.
INSTALLING OPTIONAL LINER KITS ~ Fig. 2 - Contents of CX581 stainless steel liner kit for standard 36" deep convection ovens. l _ The CX581 liner kit components are identified above.
OPERATION BEFORE FIRST USE I Before the oven is used for the first time, it must be "burned in" to release any odors that might result from heating the new surfaces in the chamber. Using a clean damp cloth, wipe the inside of the oven, including the racks.
There are 10 PRODUCT buttons (0-9) which may be programmed to automatically schedule one, two, three and/or four stages of cooking with TEMPerature, TIME, FAN and Cooking Curve setting for each stage. (CC is programmed on the first stage only but is in effect for all stages.
Ii tl ,~ U ~ Programming Mode (Cant.) DISPLAY DO 3. TIME-1 Enter the time for the 1st stage. Time is entered right to left on display. For example: To enter 2 hours you must enter a 2 and 4 zeros. HHMMSS Press START or wait 5 seconds. 4. TEMP-1 Enter temperature for first stage.
NORMAL COOKING With ON/OFF switch ON ... DISPLAY DO 101. ON Press the number of the pre-programmed PRODUCT instruction (0-9). 102. PRE-HT or COO LNG Wait for temperature to stabilize at the TEMP 1 setting. Go to 103. The LED of the PRODUCT selected will flash and other products with a TEMP-1 within 10 degrees will be lit.
Normal Cooking (Cant.) Batch Processing This feature allows you to bake several batches of the same product and stagger the loading and unloading. For example: PRODUCT 1 is programmed 10 minutes at 375°F with a fan speed of 2 and a CC of 9. Press PRODUCT 1.
COOKING TEMPERATURES AND TIMES Because of the moving air in the convection oven, the temperatures required to bake various products are lower and the cooking times are shorter than in a conventional deck-type oven with still air.
CLEANING YOUR CONVECTION OVEN Always allow the oven to cool prior to cleaning. If the oven is hot, make sure the doors are only slightly ajar to minimize the exposure of the operator to the hot air. To speed up the cooling process: Leave the door ajar.
CLEANING THE BLOWER WHEEL WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT. Remove all racks by pulling forward, lifting up and out. Remove both right and left rack supports by lifting up.
~ en ::i 2': c I I' I' 2 ib L_~'4'fTI4 i61 w !Z it BmL< FDA 2-5PEEO -...c=-rC'" I uJ D. l.40TaR (NOT SE,PMl .• TE .
An important point after buying a device Hobart MODEL PCN90 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart MODEL PCN90 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart MODEL PCN90 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart MODEL PCN90 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart MODEL PCN90 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart MODEL PCN90, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart MODEL PCN90.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart MODEL PCN90. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart MODEL PCN90 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
