Instruction/ maintenance manual of the product WS-C208 Hobart
Go to page of 10
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions WS-C206 WS-C208 - NOTICE - This Manual is prepared for the use of trained Hobart Service Technicians and should not be used by those not properly qualified. This manual is not intended to be all encompassing.
TABLE OF CONTENTS INSTALLATION ............................................................................................ 3 INSTALLATION WS-C206/WS-C208 .................................................................... 3 DISC REPLACEMENT ........
INSTALLATION INSTALLATION WS-C206/WS-C208 Disconnect the electrical power to the machine and follow lockout / tagout procedures. 1. Locate water supply line and appropriate drains for softener installation. 2. Install by-pass valving. Fig. 1 3. Install high temperature prefilter if needed.
Fig. 5 8. Install one O-Ring into each groove of the brass adapter. Fig. 6 9. Apply a small amount of seal lube evenly onto each O-ring. Fig. 7 10. Remove the pin and bracket from the softener in/ out port area. Fig. 8 11. Install the brass adapters into the in/out ports and secure by reinstalling the bracket and pin.
14. Insert tubing provided into the overflow port on the back of the softener and run drain lower than the cabinet connection to provide a gravity drain in the event of a internal cabinet leak. Fig. 10 15. Review the meter disc selection chart and the water analysis provided.
Brine Valve Settings Unit Brine Setting Float Cup Height WS-C206 .5 lb. 5.25" WS-C206 1.0 lb. 6.25" WS-C208 1.0 lb 5.25" WS-C208 1.4 lb 5.75" 23. After the adjustments have been made to the float cup, reinstall brine valve into the cabinet.
DISC REPLACEMENT DISC REPLACEMENT WS-C206/ WS-C208 1. Remove screws and cap cover from level one. Fig. 13 2. Remove balance piston. Fig. 14 3. Remove balance piston o-ring and balance piston spring. Fig. 15 4. Remove meter drive pawl. Fig. 16 5. Remove meter disc.
6. Install correct meter disc and reassemble in reverse order. NOTE: Make certain all components are correctly installed. NOTE: Be certain to start cap screws by hand rotating backwards until screw drops into thread then tighten. An alternating, crossing pattern should be used while tightening cap screws to ensure correct cap fit.
DISC SELECTION DISC SELECTION WS-C206/WS-C208 The amount of hardness removed (in compensated gpg) will be based on the amount of brine and the meter disc selected. 1. Test water supply for hardness and iron content. Use water analysis test kit available through Pro Products Inc.
WS-208 Disc Selection Disc Number 1 2 3 4 5 6 7 8 Compensated Hardness at 1.0 lb setting * 4 9 14 19 23 27 30 35 Compensated Hardness at 1.4 lb setting * 5 11 17 22 27 32 35 40 Gallons Between Regeneration 732 366 244 183 146 122 105 92 Regeneration Gallons Per Minute @ 15 psig.
An important point after buying a device Hobart WS-C208 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart WS-C208 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart WS-C208 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart WS-C208 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart WS-C208 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart WS-C208, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart WS-C208.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart WS-C208. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart WS-C208 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
