Instruction/ maintenance manual of the product ML-134252 Hobart
Go to page of 8
MODEL 2912B SLICER MODEL 2912B M L-134251 ML-134252 Previous models covered by this manual: 2912B M L-134123 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.
– 2 – © HOBART CORPORATION 1998, 2004 Installation, Operation and Care of MODEL 2912B SLICER SA VE THESE INSTRUCTIONS GENERAL The model 2912B slicer is equipped with a 1 / 2 HP motor and is available for single-phase electrical service. The slicer features the exclusive Hobart Clean Cut TM contoured stainless steel knife with super alloy edge.
– 3 – INST ALLA TION UNPACKING Immediately after unpacking the slicer, check for possible shipping damage. If the slicer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
– 4 – Fig. 2 OPERA TION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLICER MUST BE IN THEIR CORRECT OPERATING POSITIONS ANY TIME THE SLICER IS IN USE. The Top Knife Cover (Fig. 2) must be in position and secured with the Latch Knob (Fig. 2). The Ring Guard is not removable.
– 5 – WARNING : ROTATING KNIFE. USE FEED GRIP. UNPLUG MACHINE POWER CORD BEFORE CLEANING, SERVICING, OR REMOVING PARTS. REPLACE PARTS BEFORE USE. SLICING — MODEL 2912B Loading the Product With the Gauge Plate fully closed and the Automatic/Manual Lever (Fig.
– 6 – CLEANING This machine must be thoroughly cleaned and sanitized after each day’s operation or after being idle for an extended period of time. WARNING : THE SLICER KNIFE IS VERY SHARP. EXERCISE EXTREME CAUTION WHEN WORKING NEAR THE KNIFE. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES.
– 7 – Do not exceed chemical manufacturer’s recommended concentrations for detergent or sanitizer. Do not exceed 200 parts per million concentration of available chlorine. For example, mixing 1 tablespoon of 5.25% sodium hypochlorite bleach with 1 gallon of water yields a solution containing 200 ppm of available chlorine.
– 8 – FORM 34698 Rev. A (Feb. 2004) PRINTED IN U.S.A. MAINTENANCE KNIFE SHARPENING The Hobart Clean Cut TM knife will provide long service in normal food retail or commercial kitchen use. However, in high volume applications where it is a practice to sharpen the knife frequently, the knife will be expended in a shorter time.
An important point after buying a device Hobart ML-134252 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart ML-134252 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart ML-134252 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart ML-134252 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart ML-134252 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart ML-134252, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart ML-134252.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart ML-134252. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart ML-134252 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
