Instruction/ maintenance manual of the product 2812 Hobart
Go to page of 16
2812 SLICER MODEL 2812 & 2912 SLICERS MODEL 2812PS SLICER . . . with P or tion Scale MODELS 2812 M L-136110 2812PS M L-136114 2912 M L-136111 701 S.
– 2 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 3 – © HOBART, 2004 Installation, Operation, and Care of MODEL 2812 & 2912 SLICERS MODEL 2812PS SLICER with P or tion Scale SA VE THESE INSTR UCTIONS GENERAL The model 2812, 2812PS and 2912 slicers are equipped with a 1 / 2 HP motor and are available for single- phase electrical service.
– 4 – INST ALLA TION UNPACKING Immediately after unpacking the slicer, check for possible shipping damage. If the slicer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
– 5 – OPERA TION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLICER MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SLICER IS IN USE. The T OP K NIFE C OVER must be in position and secured with the L ATCH K NOB (Fig. 2). The R ING G UARD is not removable.
– 6 – The four Preset keys (1 – 4) recall the last-entered portion mode and value and display the preset indicator ( P1 , P2 , P3 , or P4 ). In WEIGHT mode, the slicer beeps when the preset weight is on the platter. In SLICE mode, the slicer beeps when the preset number of slices has counted down to 0 .
– 7 – POWER UP When the slicer is plugged in, the control checks its own circuitry, goes through a series of illuminated displays, and ends with the scale at zero in weight mode. SCALE PLATFORM AND PLATTER ASSEMBLY Proper assembly of the nylon scale platform and stainless steel scale platter is necessary before weighing.
– 8 – WEIGHT MODE The scale is ready to weigh if the zero indicator is displayed when the platter is empty. Tare is permitted. Once invoked, the Tare value is set for all WEIGHT mode operations: Manual mode, Presets (P1 – P4), and Memory (M). The Tare value can be changed or turned off at any time.
– 9 – SLICING IN MANUAL MODE . . . without using the Presets (P1 – P4) or the Memory key In Weight Mode . . . Set the Tare, if needed. Set thickness. Slice product. The displayed weight will reflect the platter weight (less Tare, if NET was displayed).
– 10 – USING THE PRESETS: P1, P2, P3, P4 Press any Preset key — the last-saved values will be called up. For example, let's press the [ 1 ] Preset key and assume that the factory settings have not been changed. In Weight Mode . . . The preset weight, 0.
– 11 – USING THE MEMORY KEY: In Weight Mode . . . You can enter the preset weight by using the numeric keys (for example, 125). The lb indicator will blink and the preset weight, 1.25 lb, displays. [ If you make a mistake, press the Clear key, , and reenter the numeric value, or press the key twice to restore the previous values.
– 12 – SLICING — MODEL 2912 With the Gauge Plate fully closed, pull the Carriage all the way toward you until it reaches its stop. With the Meat Grip out of the way, place the product to be sliced on the Carriage Tray.
– 13 – CLEANING This machine must be thoroughly cleaned and sanitized after each day’s operation or after being idle for an extended period of time.
– 14 – Fig. 7 Fig. 8 Do not exceed chemical manufacturer's recommended concentrations for detergent or sanitizer. Do not exceed 200 parts per million concentration of available chlorine. For example, mixing 1 tablespoon of 5.25% sodium hypochlorite bleach with 1 gallon of water yields a solution containing 200 ppm of available chlorine.
– 15 – MAINTENANCE WARNING : UNPLUG SLICER POWER CORD AND TURN THE INDEX KNOB FULLY CLOCKWISE BEFORE PERFORMING ANY MAINTENANCE PROCEDURE. KNIFE SHARPENING The Hobart CleanCut TM stainless steel knife will provide long service in normal food retail or commercial kitchen use.
– 16 – FORM 35203 Rev A (Nov. 2004) PRINTED IN U.S.A. LUBRICATION — Carriage Slide Rod and Sharpener Lubricate the Carriage Slide Rod with Lubriplate FMO-200-AW oil (supplied). Either squirt 8 – 10 drops every 2 – 3 months (depending on usage) in the Wick Hole on the Carriage Transport (Fig.
An important point after buying a device Hobart 2812 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart 2812 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart 2812 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart 2812 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart 2812 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart 2812, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart 2812.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart 2812. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart 2812 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
