Instruction/ maintenance manual of the product ML-104822 Hobart
Go to page of 8
N S T R U C T I O N S I 2612 SLICER MODEL 2612 & 2712 SLICERS MODELS 2612 ML-104829 2712 ML-104822 FORM 34141 (12-98) 701 S. RIDGE AVENUE TROY, OHIO 45374-0001.
– 2 – Installation, Operation, and Care of MODEL 2612 & 2712 SLICERS SA VE THESE INSTR UCTIONS GENERAL The model 2612 and 2712 slicers are equipped with a 1 ⁄ 2 HP motor and are available for single-phase electrical service. The slicer features the exclusive Hobart Stay-Sharp contoured cast solid stainless steel knife.
– 3 – PL-41249-1 SHARPENER DEFLECTOR TOP KNIFE COVER CARRIAGE TRA Y CARRIAGE TRA Y / SUPPORT ARM FENCE 1. Back out Thumb Screw. Lay Fence on Carriage Tray. 2. Rotate to Vertical. 3. Slide Fence Up. Tighten Screw. INST ALLA TION UNPACKING Immediately after unpacking the slicer, check for possible shipping damage.
– 4 – PL-41250-1 SWITCH KNOB GAUGE PLA TE LA TCH KNOB TOP KNIFE COVER CARRIAGE TRA Y RET AINING CLIP MEA T GRIP CARRIAGE TRA Y HANDLE INDEX KNOB FENCE OPERA TION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLICER MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SLICER IS IN USE.
– 5 – SLICING — MODEL 2712 With the Gauge Plate fully closed, pull the Carriage all the way toward you until it reaches its stop. With the Meat Grip out of the way, place the product to be sliced on the Carriage Tray.
– 6 – PL-41252-1 LA TCH KNOB TOP KNIFE COVER CARRIAGE TRA Y / SUPPORT ARM CARRIAGE TRA Y KNOB PL-41247-1 GAUGE PLA TE KNIFE RING GUARD P APER TOWEL PL-40863-1 GA UGE PLA TE KNIFE SHARPENER LOCK LEVER CLEANING This machine must be thoroughly cleaned and sanitized after each day’s operation or after being idle for an extended period of time.
– 7 – not exceed 200 parts per million concentration of available chlorine. For example, mixing 1 tablespoon of 5.25% sodium hypochlorite bleach with 1 gallon of water yields a solution containing 200 ppm of available chlorine. Solution with concentrations greater than 200 ppm will accelerate corrosion of metals.
– 8 – FORM 34141 (12-98) PRINTED IN U.S.A. TOP KNIFE COVER IS REMOVED PL-40917-1 TO SHARPEN: PULL SHARPENER HANDLE FULL Y FORW ARD FOR 5 SECONDS PL-41 146-1 WICK HOLE CARRIAGE SLIDE ROD CARRIAGE TRANSPORT MAINTENANCE KNIFE SHARPENING The Hobart cast stainless steel knife will provide long service in normal food retail or commercial kitchen use.
An important point after buying a device Hobart ML-104822 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart ML-104822 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart ML-104822 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart ML-104822 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart ML-104822 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart ML-104822, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart ML-104822.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart ML-104822. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart ML-104822 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
