Instruction/ maintenance manual of the product 5801 Hobart
Go to page of 12
FORM 16322 Rev. A (11-95) MODEL 5801 MEA T SA W MODEL 5801 ML-38674 EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 N S T R U C T I O N S I.
–2– Installation, Operation, and Care of MODEL 5801 MEA T SA W SA VE THESE INSTRUCTIONS GENERAL The 5801 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant 3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute.
–3– PL-40847-1 GA UGE PLA TE HANDLE INST ALLA TION UNPACKING AND ASSEMBLY Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
–4– UPPER PULLEY COVER (Plastic - Standard) The plastic upper pulley cover (Fig. 5) should be installed on the two hinge-retainers at the top and securely latched at the bottom during use. To remove the plastic upper pulley cover for cleaning, release the latch at the bottom and remove from the hinge-retainers at the top.
–5– UPPER AND LOWER PULLEYS The upper and lower pulleys are assembled on the upper and lower pulley shafts; the latch on each pulley should be seated in the groove of the pulley shaft (Fig. 7). Pulleys can be removed after the blade has first been loosened and removed.
–6– PL-40838-1 LOWER GUIDE HOLDER LOWER BLADE GUIDE ASSEMBL Y CARRIAGE In use, the carriage can roll back and forth between the left carriage stop (Fig. 9) and the right carriage stop, assuming the spring loaded carriage lock (Fig. 5) has not locked the carriage in a stationary position.
–7– REMOVING THE BLADE Remove the upper and lower pulley covers. Raise the gauge plate to its vertical position. Remove the right table by lifting its right side and sliding the table to the right to free it from the locating pins. Remove the column guard.
–8– ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON.
–9– OPERA TION SAFETY DEVICES INCORPORATED IN THIS SAW MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SAW IS IN USE. SAFETY FEATURES Upper Guide and Guard Assembly Before turning the saw.
–1 0– GAUGE PLATE When making several cuts of the same thickness (or when using the pusher plate), set the gauge plate as desired (Fig. 13) by pushing the lock lever and sliding the gauge plate to the thickness you want. A reference scale on the table indicates the thickness of cut.
–1 1– CLEANING AND SANITIZING WARNING : DISCONNECT ELECTRICAL POWER AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON BEFORE CLEANING THIS MACHINE.
–1 2– MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. LUBRICATION The motor has permanently lubricated ball bearings and requires no additional lubrication.
An important point after buying a device Hobart 5801 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart 5801 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart 5801 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart 5801 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart 5801 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart 5801, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart 5801.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart 5801. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart 5801 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
