Instruction/ maintenance manual of the product 3613 & 3713 Hobart
Go to page of 12
N S T R U C T I O N S I MODEL 3613 & 3713 SLICERS MODELS 3613 Manual Slicer ML-136143 3713 Automatic Slicer ML-136144 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.
– 2 – © HOBART CORPORATION 2007 TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Accessories & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . .
– 3 – Installation, Operation, and Care of MODEL 3613 & 3713 SLICERS SA VE THESE INSTRUCTIONS GENERAL The model 3613 and 3713 slicers are equipped with a 1 ⁄ 2 HP motor and are available for single-phase electrical service. The slicer features the Hobart CleanCut TM 13" diameter contoured stainless steel knife.
– 4 – PRODUCT TRAY The P RODUCT T RAY (Fig. 1) must be installed on the slicer. To install the P RODUCT T RAY on the slicer, lower the bottom of the S UPPORT A RM onto the C ARRIAGE H INGE P INS (Fig. 3). Tilt the P RODUCT T RAY toward the G AUGE P LATE .
– 5 – SHARPENER ROD & PIN SHARPENER MOUNT SLOT Fig. 4 ELECTRICAL This machine is provided with a three-prong grounding plug. The outlet to which this plug is connected must be properly grounded. If the receptacle is not the proper grounding type, contact an electrician .
– 6 – Fig. 9 Fig. 8 Fig. 7 P ARK PIN IN MEA T GRIP SLOT PRODUCT TRA Y MEA T GRIP SLIDE ROD MEA T GRIP ARM TOP KNIFE COVER LA TCH KNOB PRODUCT TRA Y MEA T GRIP INDEX KNOB PRODUCT TRA Y HANDLE MEA T GRIP SLOT GAUGE PLA TE MEA T GRIP SLIDE ROD P ARK PIN CARRIAGE SLOT CONTROLS SIDE P ANEL OPERA TION Rotating knife.
– 7 – SLICING — MODEL 3713 • Close the G AUGE P LATE by turning the I NDEX K NOB fully clockwise (Fig. 7). • Pull the P RODUCT T RAY (Fig. 7) all the way toward you until it reaches its stop (this is the home position). • Raise the M EAT G RIP to the top of the P RODUCT T RAY , and rest the P ARK P IN on the M EAT G RIP S LOT .
– 8 – CLEANING This machine must be thoroughly cleaned and sanitized at least as often as required by local regulation or after being idle for an extended period of time. The slicer knife is very sharp. Exercise extreme caution when working near the knife.
– 9 – Clean completely around the R ING G UARD by working a moistened, folded paper towel between the R ING G UARD and the K NIFE (Fig. 15). Wash, rinse and sanitize both sides of the K NIFE by wiping outward from the center. Never clean any part of the slicer with steel pads.
– 10 – Using the Knife Removal Tool Accessory Unplug the machine power cord and turn the index knob fully clockwise to close the gauge plate before cleaning the slicer. To Remove the Knife . . . • Remove the T OP K NIFE C OVER and the plastic R ING G UARD C OVER (Figs.
– 11 – To Reinstall the Knife . . . • Orient the R IDGE on the K NIFE H UB so it points to the P IN on the R ING G UARD at the 1 o'clock position (Fig. 24). • Place the K NIFE and T OOL so the P IN on the K NIFE R EMOVAL T OOL is at the 11 o'clock position (Fig.
– 12 – FORM 35218 (Oct. 2007) MAINTENANCE Unplug the machine power cord and turn the index knob fully clockwise t o close the gauge plate before doing any maintenance on the slicer. KNIFE SHARPENING The CleanCut TM K NIFE will provide long service in normal food retail or commercial kitchen use.
An important point after buying a device Hobart 3613 & 3713 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart 3613 & 3713 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart 3613 & 3713 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart 3613 & 3713 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart 3613 & 3713 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart 3613 & 3713, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart 3613 & 3713.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart 3613 & 3713. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart 3613 & 3713 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
