Instruction/ maintenance manual of the product 2912 ML-104963 Hobart
Go to page of 8
N S T R U C T I O N S I 2812 SLICER MODEL 2812 & 2912 SLICERS MODELS 2812 ML-104958 2912 ML-104963 Previous models covered by this manual: 2812 ML-104615 ML-104827 2912 ML-104713 ML-104823 ML-104874 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.
– 2 – © HOBART CORPORATION, 1998 Installation, Operation, and Care of MODEL 2812 & 2912 SLICERS SA VE THESE INSTRUCTIONS GENERAL The model 2812 and 2912 slicers are equipped with a 1 ⁄ 2 HP motor and are available for single-phase electrical service.
– 3 – PL-41408-1 SHARPENER DEFLECT OR T OP KNIFE CO VER CARRIAGE TRA Y CARRIAGE TRA Y / SUPPORT ARM FENCE INST ALLA TION UNPACKING Immediately after unpacking the slicer, check for possible shipping damage. If the slicer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
– 4 – PL-41409-1 SWITCH KNOB GA UGE PLA TE LA TCH KNOB T OP KNIFE CO VER CARRIAGE TRA Y RET AINING CLIP MEA T GRIP CARRIAGE TRA Y HANDLES INDEX KNOB FENCE OPERA TION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLICER MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SLICER IS IN USE.
– 5 – Fig. 3 PL-41257-1 SWITCH KNOB SPEED SELECTOR KNOB LEVER IN MANUAL (DOWN) POSITION LA TCH KNOB GAUGE PLA TE TOP KNIFE COVER CARRIAGE TRA Y SHARPENER INDEX KNOB CARRIAGE HANDLES MEA T GRIP RET AINING CLIP SLICING — MODEL 2912 With the Gauge Plate fully closed, pull the Carriage all the way toward you until it reaches its stop.
– 6 – PL-41403-1 GA UGE PLA TE KNIFE RING GUARD P APER TO WEL PL-41402-1 GA UGE PLA TE KNIFE SHARPENER LOCK LEVER PL-41258-1 LA TCH KNOB TOP KNIFE COVER CARRIAGE TRA Y / SUPPORT ARM CARRIAGE TRA Y KNOB CLEANING This machine must be thoroughly cleaned and sanitized after each day’s operation or after being idle for an extended period of time.
– 7 – not exceed 200 parts per million concentration of available chlorine. For example, mixing 1 tablespoon of 5.25% sodium hypochlorite bleach with 1 gallon of water yields a solution containing 200 ppm of available chlorine. Solution with concentrations greater than 200 ppm will accelerate corrosion of metals.
– 8 – FORM 34454 (Feb. 2000) PRINTED IN U.S.A. T OP KNIFE CO VER IS REMO VED PL-41404-1 T O SHARPEN: PULL SHARPENER HANDLE FULL Y FORW ARD FOR 5 SECONDS MAINTENANCE KNIFE SHARPENING The Hobart cast stainless steel knife will provide long service in normal food retail or commercial kitchen use.
An important point after buying a device Hobart 2912 ML-104963 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart 2912 ML-104963 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart 2912 ML-104963 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart 2912 ML-104963 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart 2912 ML-104963 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart 2912 ML-104963, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart 2912 ML-104963.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart 2912 ML-104963. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart 2912 ML-104963 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
