Instruction/ maintenance manual of the product 581 Henny Penny
Go to page of 12
This section provides troubleshooting information in the form of an easy to read table. If a problem occurs during the first operation of a new fryer, recheck the installation per the Installation Section of this manual. Before troubleshooting, always recheck the operation pro- cedures per Section 3 of this manual.
Product Color Not Correct: A. Too Dark B. Too Light C. Product Greasy Temperature too high. Shortening too old. Shortening too dark. Breading product too far in advance. Wrong cook button pushed. Temperature too low. Fryer incorrect preheat. Slow fryer heat-up/ recovery.
B. Too Light C. Product Greasy D. Spotted Product Temperature too low. Fryer incorrect preheat. Slow fryer heat-up/ recovery. Wrong cook button pushed. 0 Shortening old. Temperature too low. 0 Cookpot overloaded. Product not removed from cookpot immediately after end of cycle.
E. Dryness of Product Product Flavor (Taste): A. Salty Taste urned Taste 6. Bland Taste Moisture loss prior to cooking. Overcooking the product. Low operating pressure. Wrong cook button pushed. Breading mixture is too salty. Incorrect choice of breading.
D. Rancid Taste Replace shortening, and follow recommended care and use of shortening. Replace shortening. Use compatible products, and follow recommended care and use of shortening. General: A. Meat Separation From Bone B. Bone Color Not Proper 6. Breading Falh Off D.
With switch in POWER position, the fryer is com- pletely inoperative (NO POWER) Pressure will not exhaust at end of cooking cycle. Operating pressure too high Open circuit. Exhaust line from solenoid valve to condensation tank clogged. Solenoid valve clogged.
Henny Penny Model 581 Problem Cause Correction LID/PRESSURE SE CTION (Continued) • Exhaust line to stack clogged • Clean exhaust line to stack. DO NOT OPERATE UNIT IF HI GH PRESSURE CONDITIONS EX IST, SEVERE INJURIES AND BURNS WILL RESULT. Place th e Power/P ump switch in the “OFF ” position immediately .
Henny Penny Model 581 Problem Cause Correction LID/PRESSURE SE CTION (Continu ed) • Safet y relief valve le aking. • Check and replac e if necessar y per maintenance section on the re lief valve. • Pressure pad broken or crushed. • Replace pressure p ads.
Heating of shortening too slow (Electric Model) Shortening overheating (Electric Model) Foaming or boil- ing o,ver of shortening Low or improper voltage. Weak or burnt out element(s). Points in contactor bad. Wire(s) loose. Burnt or charred wire connection.
Shortening will not drain from cookpot Shortening leaking through drain valve. Cold zone full of cracklings. Improper rinsing after cleaning the fryer. Too much stirring. Drain valve clogged with crumbs. Drain valve will not open by pulling the knob. Obstruction in drain.
The following guide requires voltage to be present when troubleshooting the control. When the guide refers to connecting pins on the power connection, unplug the power connector from the board and refer to the attached illustration. These are numbered 1 through 9.
Error message E-5 display reads HI. Error message E-6. Error message E-10. Error message E-41. Read display temperature - if display temperature reads HI, unplug power connector from control board. If secondary contactor stays engaged, change contactor - if secondary contactor disengages, change control board.
An important point after buying a device Henny Penny 581 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny 581 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny 581 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny 581 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny 581 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny 581, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny 581.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny 581. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny 581 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
