Instruction/ maintenance manual of the product 520 Henny Penny
Go to page of 15
Y et 52 .
Henny Penny Model 520 SECTION 3. OPERA TION 3-1. OPERA TING CONTROLS Item Description Function 1 Main Power Switch A three way rocker switch with a center off position. Pressing with Built- In Indicator the left side of the rocker switch (COOK position) operates the Lights fryer , and the amber light illuminates.
Henny Penny Model 520 Item Description Function 7 Safety Relief V alve The safety relief valve is set at 14.5 PSI (99.9 KPa). In the event that the dead weight valve becomes clogged, the safety valve releases excessive pressure, keeping the frypot at a maximum of 14.
el 520 ke 15 High Temperature Control Lid/Locking Assembly Condensate Drain Pan Fun~tio~ The high temperature thermostat is a manual reset control which senses the temperature of the shortening. If the shorten- ing temperature exceeds the safe operating limit, this control will remove power from the contactors, thus removing heat to the cook pot.
Henny Penny Model 520 Item 6 Item 7 Item 9 Item 10 Item 1 1 Item 12 Item 9 3-4 101.
The first step in the use of the Henny Penny Model 520 is to learn the controls. Next, determine the time and temperature settings. The following will assist you in determining these settings but are approximate and will vary with the size and quantity of the raw product.
del 52 The following procedures should be followed in the initial start-up of the fryer and each time the fryer is brought from a cold or shut down condition back into operation. 1. Check to see that all control switches are turned OFF. 2. Be sure that the drain valve and filter valve are closed.
el 520 Step 3 3-5. COOKING Gloves should be worn and care must be taken when pouring hot shortening into the unit. Severe burns could result. Also, when adding fresh shortening to existing shortening, care must be taken to avoid splashing. 3. Cold shortening should be filled approximately 112 inch below the bottom level of the level indicator line.
Henny Penny Model 520 3-5. COOKING PROCEDURES 8. Raise the lid promptly to allow most of the condensation (Continued) on the lid to drain down and out through the drain channel. Do not let the lid slam up against the back stop. This could damage the hinge assembly .
el 520 The filter pan must be in the proper position beneath the drain valve. This will prevent the splashing of the hot shortening as it drains into the filter drain pan which would cause burns. 3. Open the drain valve by pulling it forward slowly. This will prevent excessive splashing of the hot shortening as it drains into the filter drain pan.
3-6. FILTERING THE S TENING (Co~ti GING T F~LTE ENVELOPE el 520 D. Wash down and scrub the sides of the cook pot. Use “L” brush to clean the heating elements. E . After the sides and bottom are cleaned, open the drain valve. 7. Pump all the shortening out of the filter pan and back into the cook pot.
FILTE ti~~e~) This union will be hot. Use protective glove or cloth to prevent burns. 4. Lift the screen assembly from the drain pan. Step 3 5. Wipe the shortening and crumbs from the drain pan. Clean the drain pan with soap and water. Thoroughly rinse with hot water.
ENVELOPE (Co~ti~~ed) Step 8 Step 10 tep 11 tep 12 8. Remove filter clips and discard the filter envelope. 9. Clean the top and bottom filter screen with soap and water.
Henny Penny Model 520 3-8. CLEANING THE FR YPOT T aste the cold shortening every day for flavor . W atch the shortening for foaming during the cook cycle. Discard the shortening as soon as it shows signs of foaming. Drain and clean the frypot as follows: 1.
Henny Penny Model 520 3-8. CLEANING THE FR YPOT 6. When the set temperature is reached, turn unit off. (Continued) W atch cleaning solution constantly to make sure it does NOT boil over causing damage to controls. If the cleaning solution starts to foam and boil over , DO NOT CLOSE THE FR YER LID, severe burns could result.
An important point after buying a device Henny Penny 520 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny 520 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny 520 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny 520 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny 520 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny 520, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny 520.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny 520. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny 520 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
