Instruction/ maintenance manual of the product SL-550TR-IPI-E Heat & Glo
Go to page of 87
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 1 • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: ______.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 4 = Contains updated information. 13 Finishing A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 57 B. Facing Material . . . . . . . . . . . . . .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 5 B. Limited Lifetime W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”).
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 6 B. Limited Lifetime W arranty (continued) • This limited warranty does not extend to or include surface fi nish on the a.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 7 B. T empered Glass Speci fi cations Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous loca- tions such as bathtub enclosures as de fi ned by the Con- sumer Product Safety Commission (CPSC).
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 8 E. Non-Combustible Materials Speci fi cation Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 9 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 10 Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 1 1 D. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 12 I. Lighting Instructions (IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove them when using the transformer .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 13 J. Lighting Instructions (Standing Pilot) 1. Turn of f all electric power to the appliance if ser- vice is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 14 Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 15 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 16 V enting Frequency: Seasonally By: Homeowner T ools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow , debris, etc.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 17 (Either cobrahead or SIT) PRODUCT SPECIFIC Figure 3.2 IPI Pilot Flame Patterns Figure 3.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 18 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 19 B. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 20 5 5 F raming and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 21 B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 22 D. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing or fi nishing material closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 23 Figure 6.3 Leveled T ermination Caps A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 24 O N P R Q V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 6.4 Minimum Clearances for T ermination A = 12 inches................. clearances above grade, ver anda, porch, deck or balcony B = 12 inches.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 25 A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies DVP or SLP venting systems. Refer to Sec- tion 16B for vent component information. DO NOT mix pipe, fi ttings or joining methods from differ- ent manufacturers.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 26 3i n . C L E A R A N C E T E R M IN AT IO N CAP F LEX - V ENT 1i n . CLEAR AN CE E. Use of Flex V ent The fl ex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than 1/2 inch sag between supports.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 27 Figure 7.4 F . V ent Diagrams T op V ent - Horizontal T ermination V enting with 1 elbow H 1 V 1 V 1 Minimum H 1 Maximum SL-550TR-E SL-750TR-E SL-950TR-E 90 Elbow 2 ft. 610 mm 2 ft.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 28 INST ALLED HORIZONT ALL Y H 1 H 2 V 1 Figure 7.5 T op V ent - Horizontal T ermination V enting with 2 elbows V Minimum H 1 + H 2 Maximum SL-550TR-E SL-750TR-E SL-950TR-E 90 Elbow 1/2 ft.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 29 Figure 7.6 H 2 H 1 V 2 V 1 T op V ent - Horizontal T ermination V enting with 3 elbows V 1 Minimum H 1 + H 2 Maximum SL-550TR-E SL-750TR-E SL-950TR-E V 2 V 1 + V 2 Min. 90 Elbow 2 ft.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 30 Figure 7.7 Note: If installing a vertical vent/termination off the top of the appliance, the optional vertical termination baf fl e may be needed. V 1 V 1 = 60 ft. Max. (18.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 31 Figure 7.9 H 1 V 1 V 2 T op V ent - V ertical T ermination V enting with 2 elbows V 1 MIN. SL-550TR-E SL-750TR-E SL-950TR-E H MAX. H MAX. H MAX. V 2 V 1 + V 2 MIN. 90 Elbow 1-1/2 ft.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 32 Figure 7.10 INST ALLED HORIZONT ALL Y H 1 H 2 V 1 V 2 T op V ent - V ertical T ermination V enting with 3 elbows V 1 MIN. SL-550TR-E SL-750TR-E SL-950TR-E H MAX. H MAX. H MAX.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 33 T op V ent - V ertical T ermination V enting with 4 elbows Note : Use SLP Series components only . Note : There MUST be a 25% reduction in total H when using fl ex vent except when using the simple up and out installation (see Figure 7.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 34 Figure 7.13 Figure 7.12 Rear V ent - Horizontal T ermination No Elbows H 1 = 9 in. (229 mm) Maximum Rear V ent - Horizontal T ermination One 45º Elbow For corner installation of models SL-550TR-E and SL-750TR-E ONL Y Note : Do not use a 45º elbow for SL-950TR-E.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 35 Rear V ent - Horizontal T ermination V enting with 2 elbows H 1 MAX. V 1 MIN. H 2 MAX. H 1 + H 2 MAX. 1-1/2 ft. 457 mm Back to back elbows 1 ft. 305 mm 2-1/2 ft. 762 mm 3 ft.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 36 Figure 7.16 Figure 7.17 V 1 H 1 V 1 H 2 H 1 IN S T A LL E D HORI ZONT ALL Y Rear V ent - V ertical T ermination V enting with 1 elbow V 1 MIN. H 1 MAX. 1 ft. 305 mm 3-1/2 ft.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 37 V 1 MIN. H 1 MAX. H 2 MAX. H 1 + H 2 MAX. Back to back elbows 1-1/2 ft. 457 mm 1 ft. 305 mm 2-1/2 ft. 762 mm 1 ft. 305 mm 3-1/2 ft. 1.1 m 3 ft. 914 mm 6-1/2 ft. 2.0 m 2 ft. 610 mm 5-1/2 ft.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 38 A. Pipe Clearances to Combustibles W ARNING! Risk of Fire! Maintain air space clearance to vent.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 39 C. Install the Ceiling Firestop A ceiling fi restop MUST be used between fl oors and attics. • DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ fl oor (see Figure 8.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 40 D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 41 CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 42 B. Rear V ent NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. NOTICE: Once the seal cap has been removed it CANNOT be reattached.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 43 C. Securing and Leveling the Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of blown- in insulation.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 44 1 0 10 Installing V ent Pipe ( D VP and SLP P ipe ) A. Assemble V ent Sections (DVP Pipe Only) Attach V ent to the Firebox Assembly Note: The end of th e pipe secti ons with the lanc ed tabs will f ace toward the applianc e.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 45 B. Assemble V ent Sections (SLP Pipe Only) T o attach the fi rst vent component to the starting collars of the appliance: • Attach an SLP-DVP24 adapter to the starting collar of the appliance.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 46 120º Figure 10.8 Securing V ertical Pipe Sections 120º Figure 10.9 Securing Horizontal Pipe Sections E. Disassemble V ent Sections • Rotate either section (see Figure 10.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 47 F . Install Decorative Ceiling Components (SLP only) A decorative ceiling thimble can be installed on a fl at ceil- ing through which the vent passes. The decorative ceiling thimble is used to cover the fi restop.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 48 G. Install Metal Roof Flashing Note : Skip this section if using the RF4-8. • See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 49 I. Install RF4-8 The RF4-8 may be used in place of the roof fl ashing and storm collar (Sections 10.G. and 10.H.) Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF4-8 Flashing.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 50 SCREWS CAULK STORM COLLAR (1 of 3) Figure 10.23 Figure 10.23 TERMINA TION CAP J.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 51 Figure 10.25 Venting through the wall INTERIOR HEA T SHIELD OR EXTENDED HEA T SHIELD W ALL SHIELD FIRESTOP HEA T SHIELD 1-1/2 IN.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 52 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts.
3 5 8 0 / 1 1 • L . v e R 0 0 9 - 8 1 1 2 • E - R T 0 5 9 / 0 5 7 / 0 5 5 - L S • o l G & t a e H Figure 12.1 Ignitor Button C. Standing Pilot Ignition System Wiring • The stan ding pilo t ignition system wirin g does not require a 1 10 V AC supply to operate.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 54 TRANSFORMER 3 V AC PLUG IN BLACK RED BA TTERY P ACK THERMOST A T WIRE ASSEMBL Y WIRES (TO BROWN) ORANGE GREEN VA LV E WHITE ORANGE IGNITION MODULE 3 V AC INTERMITTENT PILOT IGNITOR HOT NEUTRAL I S GROUND TO FIREPLACE CHASSIS Figure 12.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 55 Figure 12.4 Standing Pilot Ignition Wiring Diagram THERMOST A T WIRE ASSEMBL Y PIEZO WHITE RED VA LV E PILOT THERMOCOUPLE THERMOPILE E. Electrical Service and Repair W ARNING! Risk of Shock! Label all wires prior to dis- connection when servicing controls.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 56 G. W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.6): • The power supply for the appliance must be brought into a switch box.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 57 A. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materi- als (i.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 58 B. Facing Material • Metal front faces may be covered with non-combustible materials only . • Facing and/or fi nishing materials must not interfere with air fl ow through louvers, operation of louvers or doors, or access for service.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 59 C. Splatter Guard The splatter guard is a piece of corrugated material used to protect the appliance during the installation process before fi nishing work on the whole hearth is complete.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 60 Step 5. Fold bottom fl ap along score line as indicated in Figure 13.13 and tuck into valve access area of appli- ance. Splatter guard should fi t securely on front of unit.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 61 D. Doors Only doors certi fi ed for use with this appliance model may be used.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 62 E. Elevated Hearth Systems Use the table below to identify the hearth system that will be used. The table will also help identify ef fects on the various dimensions. Some hearth systems will elevate the appliance off the fl oor at a given dimension.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 63 A. Remove Fixed Glass Assembly See Section 14.G. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 64 Log Set Assembly: LOGS-550-E, 750-E, 950-E Model: SL-550TR-E, 750TR-E, 950TR-E, SL-550TV -E, SL-750TV -E, SL-950TV -E F . Install the Log Assembly If the gas logs have been factory installed they should not need to be positioned.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 65 Log should touch lava rock retainer Log should touch lava rock retainer Figure 7 Figure 7 Log #3 : Locate the pin hole on the underside of log #3. Mate the pin hole with the shoulder screw located on the burner top.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 66 Figure 14.4 Air Shutter Figure 14.3 Fixed Glass Assembly G. Fixed Glass Assembly W ARNING! Risk of Asphyxiation! Handle fi xed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 67 A. Standing Pilot Ignition System 1 5 15 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 68 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. (Continued) C. V alve. T urn the valve knob to the ON position. Place the ON/ OFF switch in the ON position.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 69 B. Intelli fi re Ignition System Symptom Possible Cause Corrective Action 1.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 70 Intelli fi re Ignition System - (continued) Symptom Possible Cause Corrective Action 4.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 71 1 6 16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only . For framing dimensions and clearances refer to Section 5.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 72 B. V ent Components Diagrams Figure 16.2 DVP vent components 10- 1/2 i n. (267 m m ) 10 -7/ 8 in . (2 76 m m ) 45 ° 7- 3 / 8 i n . ( 1 8 7 mm) 11- 3 / 8 in . (289 m m ) 1-1 /4 in .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 73 B. V ent Components Diagrams ( continued ) Figure 16.3 DVP vent components DVP-HPC1 DVP-HPC2 DVP-TRAP1 DVP-TRAP2 DVP-TRAPK2 DVP-TRAPK1 DVP-TRAP Horizontal T ermination Cap 15-1/8 in.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 74 B. V ent Components Diagrams ( continued ) Figure 16.4 DVP vent components 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 75 B. V ent Components Diagrams (continued) Figure 16.5 DVP vent components DVP-TB1 Basement V ent Ca p 12 in. (305 mm) 1-1/2 in. (38 mm) 7-3/8 in. (187 mm) 14 in. (356 mm) 17-3/4 in.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 76 B. V ent Components Diagrams (continued) Figure 16.7 SLP Series V ent Components Figure 16.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 77 B. V ent Components Diagrams (continued) Figure 16.8 SLP Series V ent Components 8-3/4 in.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 78 B. V ent Components Diagrams (continued) Figure 16.8 SLP Series V ent Components SLK-SNKD Snorkel T ermination Cap SLP-TVH.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 79 Part number list on following page. C. Service Parts Service Parts Diagram Beginning Manufacturing Date: June 2007 Ending .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 80 Service Parts List SL-550TR-E, SL-550TR-IPI-E IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 81 6 7 8 9 Service Parts Service Parts Diagram Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: ______ SL-750TR-E, SL-750TR-IPI-E Part number list on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 82 Service Parts List SL-750TR-E, SL-750TR-IPI-E IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 83 Service Parts Service Parts Diagram Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: ______ SL-950TR-E, SL-950TR-IPI-E 6 7 8 9 10 11 Part number list on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 84 Service Parts List SL-950TR-E, SL-950TR-IPI-E IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number .
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 85 Service Parts V alve Assembly Diagram/ Parts List SL-550 / 750 / 950TR-IPI-E Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: ______ IPI V alve Assembly 1 2 3 4 5 6 7 8 9 10 11 12 IMPORT ANT : THIS IS DA TED INFORMA TION.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 86 Service Parts V alve Assembly Diagram/ Parts List SL-550 / 750 / 950TR-E Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: ______ Standing Pilot V alve Assembly 1 2 3 4 5 6 7 8 9 IMPORT ANT : THIS IS DA TED INFORMA TION.
Heat & Glo • SL-550 / 750 / 950TR-E • 21 18-900 Rev . L • 1 1/08 87 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 7571 215th St, Lakeville, MN 55044 www .heatnglo.com D. Contact Information Please contact your Heat & Glo dealer with any questions or concerns.
An important point after buying a device Heat & Glo SL-550TR-IPI-E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Heat & Glo SL-550TR-IPI-E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Heat & Glo SL-550TR-IPI-E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Heat & Glo SL-550TR-IPI-E you will learn all the available features of the product, as well as information on its operation. The information that you get Heat & Glo SL-550TR-IPI-E will certainly help you make a decision on the purchase.
If you already are a holder of Heat & Glo SL-550TR-IPI-E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Heat & Glo SL-550TR-IPI-E.
However, one of the most important roles played by the user manual is to help in solving problems with Heat & Glo SL-550TR-IPI-E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Heat & Glo SL-550TR-IPI-E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
