Instruction/ maintenance manual of the product P61-2 Harman Stove Company
Go to page of 24
P61-2 Pellet S tove Owners Manual SAFETY NOTICE PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INST ALL AND USE YOUR NEW ROOM HEA TER.
2 Fig. 1.
3 Please read this entire manual before you install and use your new room heater . Failure to follow instructions may result in property damage, bodily injury , or even death.
4 Unpacking The P61 is bolted to the skid to prevent move- ment during shipping. To free the stove from the skid you must re- move the hold-down bolts in the rear of the pedestal base.
5 Inst alling Place the stove on a noncombustible floor or UL approved floor protector that extends 6 inches to the front, 6 inches to the sides and 1 inch to the rear of the stove.
6 V enting Requirement s for T erminating the V enting W ARNING: V enting terminals must not be re- cessed into a wall or siding.
7 A combustion blower is used to extract the com- bustion gases from the firebox. This causes a nega- tive pressure in the firebox and a positive pressure in the venting system as shown in fig.
8 #2 Preferred method This method also provides excellent venting for normal operation but requires the stove to be installed farther from the wall.
9 #4 Inst alling into an existing chimney ( US only ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure.
10 #6 Inst alling into an existing fireplace chimney ( US and Canada ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure.
11 #8 Inst alling through the ceiling vent Through the ceiling vent, follow PLvent manufacturers recommendations when using wall and ceiling pass through.
12 Operation St arting First Fire Be sure the power cord is plugged into a 120 volt receptacle. This can be verified by the red power light on the control panel.
13 When to use "Stove T emp Mode" In "S tove T emp Mode" the S tove T emp Dial de- termines the temperature of the stove. Heat output and fuel consumption will remain constant.
14 ESP CONTROL Feed adjuster Sets the maximum feed ra te Test Runs all motors at full speed for two minutes to check operation.
15 The room sensor is a small temperature sen- sor on the end of a 60" gray wire. This sensor is installed much like a standard wall thermostat.
16 Removing Ashes: When approximatly 1 ton of pellets has been burned it will be necessary to empty the ash pan. Ashes should be placed in a metal con- tainer with a tight fitting lid.
17 Latch "closed "with blower cover in place. Burn pot clean-out is closed. Latch "open "with blower cover partly removed. Burn pot clean-out is open. Exposed blower wheel and flue opening, NOTE: ESP probe is visible.
18 FEEDER DOES NOT FEED 1. No pellets in hopper . 2. Feed motor will not run until ESP senses 165 deg. F. Maybe you did not put enough pellets in the burn pot before lighting the fire.
19 Weight 249 lbs. Blower 135 cfm Feed Rate .75 to 7.5 lbs. per hr . Hopper Capacity 72 lbs. Fuel Wood Pellets Flue Size 3 inch Outside Air Size 2 3/8 I.D. inch Fuse Rating 5 amp 32.
20 P61-2 Wiring Diagram.
21 Door Options Optional T rim To install, lay the frame face down on a sof t surface. Fasten door frame by inserting the 4 threaded post s on the frame through the door .
22 OPTIONS Side Heat Shields Side heat shields are available to reduce the clearance to combustible materials.
23 Description Part Number Hopper Gasket(6 ft.) 0-88-00248 Ash Pan Assembly 1-10-05800 Burn Pot Weldment 1-10-05802 Right Rear Shield 2-00- 06468-1 Left Rea.
24 Harman S tove Company warrants its products to be free from defects in material or workmanship, in normal use and service.
An important point after buying a device Harman Stove Company P61-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harman Stove Company P61-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harman Stove Company P61-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harman Stove Company P61-2 you will learn all the available features of the product, as well as information on its operation. The information that you get Harman Stove Company P61-2 will certainly help you make a decision on the purchase.
If you already are a holder of Harman Stove Company P61-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harman Stove Company P61-2.
However, one of the most important roles played by the user manual is to help in solving problems with Harman Stove Company P61-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harman Stove Company P61-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
