Instruction/ maintenance manual of the product DVC-500 Harman
Go to page of 36
R1 .
2 This appliance is also approved for installation into a shop. .
3 W arnings 4 Introduction 5 Assembly 6 Installation 7 Direct V ent Pipe 14 DVC500 Microprocessor Control 15 Operation 17 Maintenance 19 Fuel 23 Wiring Diagram 25 Control and Safety Sensors 26 Parts 27 Specications 30 T roubleshooting 31 Please read this entire manual before you install and use your new room heater .
4 .
5 This remarkable design by Harman features the V erti-ow Direct V ent Stoker System. This unique, high efciency unit uses only outside air for combustion. Micro-processor controls provide for an automatic wide range of heat output from 7,000 to 75,000 BTU .
6 1. Install the hopper latch as shown at left. 2. Install 3 rebricks on the cast iron angle be- hind the grate as shown. 3. Cement in grates as shown below .
7 4 GLASS RET AINER CLIPS 4 GLASS RET AINER BOL TS GLASS GLASS GASKET DOOR HINGE PINS P A W BOL T The glass in your Harman stove is a special ceramic glass. • Do not abuse the glass by striking or slamming the door .
8 T ips On Installation Before the positioning of the unit can be decided a few questions should be considered? 1. Can the unit be vented properly and installed safely? 2. W ill exhaust be vented where fumes can build up or be drawn into lower levels of the structure 3.
9 8. Complete any other exterior ue piping necessary , using 4" pellet venting. 9. Back inside, place the 2 halves of the interior wall trim plate over ue pipe. Using the black pop rivets, fas te n toge the r , the n slid e it agai ns t the wal l and f ast en it to the wall.
10 Installation .
1 1 T o install a DVC 500 in a basement you will need additional DVC vent sections. These sections are made with a 316-grade stainless steel liner and a 20 gauge galvaneeled outer shell.
12 .
13 .
14 Exterior T ermination for wall thickness up to 8 inches 1-10-08310 Exterior T ermination for wall thickness up to 16 inches Exterior T ermination for wall thickness up to 12 inches 3-44-06256 1-10-.
15 Feed Adjuster Sets the maximum feed rate, 1 to 5 T est Runs all motors at full speed for two minutes to check operation. After two minutes the feeder stops and the distribution blower alternates from high to low every four seconds to remind you that you are still in "T est Mode".
16 ESP Contr ol Hopper Lid Latch Ash Door Latch Handle Glass Door Latch Handle Side Panel Latch.
17 T urn the Feed Adjuster to "T est" mode, (g. 13.) This will cause all motors to run 100% for 2 minutes. The lights on the control panel will be lit for each motor . If you leave it on "test" the blowers will cycle as an audible reminder .
18 This settin g will pr oduce mediu m heat with the Distribut ion Blower on "low". Fig. 16 In ".
19 .
20 The small Fines T ray in the side of the stoker should be removed and emptied T o remove the Fines T ray , rst open the door on the left rear of the stove.
21 .
22 1. Allow the stove to run out of coal in order to extinguish the re. This saves having to remove the coal from the hopper manually and most importantly , drives the moisture out of the stove that may be present in the coal.
23 Fuel The DVC500 is designed to burn Anthracite Rice Coal, which is approximately 3/8" long and wide by 3/16 thick. Anthracite coal is considered either White Ash or Red Ash. White Ash Coal will have 13 to 14,000 btu's per lb.
24 The DVC500 grate system is composed of four pieces: the grate holder , (2)-63 hole grate inserts, and grate angle. The grate angle is bolted to the grate holder with (2) 3/8 x 1 1/4 bolts. Before installing the grate holder , 3/8" round gasket must be checked in the groove on the bottom side of the grate holder , as shown in Fig 31.
25 It is recommended that End of Season Cleaning and the Annual Service are coordinated to happen at the same time for best results. BLACK BLACK -- 2.5 A. -- 300 W A T TS P ART NO. 3-89-08193 Rev A 120 VOL TS A.
26 The ESP (Exhaust Sensing Probe) is a temperature sensing probe located in the exhaust outlet. The ESP works with the Control to perform all burn rate functions as well as high and low limit control.
12/1 1 .
12/1 1 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
12/1 1 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
30 Weight 500 Pounds BTU Output Range 7000 to 75,000 Heating Capacity 2200 Square Feet Fuel Anthracite Rice Coal Hopper Capacity 93 Pounds Distribution Blower S.
31 DVC 500-C Firebox Static Pr essure Safety Protocol The DVC-500 operates with a negative pressure rebox as a safety feature. The control continuously adjusts the draft motor speed to maintain a safe rebox negative static.
32 Cau se s A nd /Or Re aso ns For (2 -bl in k) Shu td own : The DVC-500 operates with a negative pressure rebox as a safety feature. Any loss of this negative pressure will start the safety protocol, ( A two blink status warning ) The following list of potential reasons for warnings is in order of most likely to least likely to occur: 1.
33 4021-645C 12-29-10 Page 1 of 2 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY Hearth & Home T echnologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer .
34 4021-645C 12-29-10 Page 2 of 2 W ARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor . A list of HHT authorized dealers is available on the HHT branded websites. • This warranty is only valid while the HHT appliance remains at the site of original installation.
35 Date Of Service Performed By Description Of Service.
Proudly P rinted On 100% Recycled P aper.
An important point after buying a device Harman DVC-500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harman DVC-500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harman DVC-500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harman DVC-500 you will learn all the available features of the product, as well as information on its operation. The information that you get Harman DVC-500 will certainly help you make a decision on the purchase.
If you already are a holder of Harman DVC-500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harman DVC-500.
However, one of the most important roles played by the user manual is to help in solving problems with Harman DVC-500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harman DVC-500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
