Instruction/ maintenance manual of the product TABLE SAW - 10 INCH DIRECT DRIVE Harbor Freight Tools
Go to page of 25
T T T T T ABLE SA ABLE SA ABLE SA ABLE SA ABLE SA W - 10 INCH W - 10 INCH W - 10 INCH W - 10 INCH W - 10 INCH DIRECT DRIVE DIRECT DRIVE DIRECT DRIVE DIRECT DRIVE DIRECT DRIVE ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 MISSION OAKS BL VD ., CAMARILLO , CA 93011 VISIT OUR WEB SITE A T HTTP://WWW .
Page 2 SKU 91815 SPECIFICA TIONS Item Desc ription Power R eq uirements 115 VAC, 1 5 am ps, 60 Hz Power Cord Length: 43 inches; 14 AWG x 3C, 3-prong plug Switch Ty pe Toggle with pull-ou t k e y s afety lock Motor Capac ity 1.
Page 3 SKU 91815 Electrical Safety 4. A v oid body contact with gr ounded surfaces such as pipes, radiator s, ranges, and refrigerators. There is an increased risk of electr ic shock if y our body is grounded. 5. Do not expose po wer tools to rain or wet conditions.
Page 4 SKU 91815 14. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the po wer tool in une xpected situations. 15. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used f or appropr iate conditions.
Page 5 SKU 91815 SPECIFIC SAFETY RULES FOR THE TABLE SA W 1 . Maintain labels and nameplates on the T able Sa w . These carry impor tant inf ormation. If unreadable or missing, contact Harbor F reight T ools for a replacement. 2. Alw a ys wear ANSI approved saf ety impact e ye goggles and hea vy work glov es when using the T ab le Saw .
Page 6 SKU 91815 21. Many saw accidents are caused by dull, badly set, and improperly filed cutting blades; gum or resin adhering to the cutting blade; and by sa w blade misalignment with the f ence. Such conditions can cause the stock to stic k, jam, stall the saw b lade, or kic k back at the oper ator .
Page 7 SKU 91815 W ARNING! Some dust created by po wer sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known (to the State of Calif ornia) to cause cancer , bir th defects or other repr oductive harm.
Page 8 SKU 91815 2 . The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’ s grounding system and must ne v er be attached to an electrically “live” terminal.
Page 9 SKU 91815 6 . If you are using an e xtension cord outdoors , mak e sure it is marked with the suffix “W - A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7 . Make sure your extension cord is properly wired and in good electrical condition.
Page 10 SKU 91815 UNP A CKING When unpacking, chec k to make sure that all the par ts are included. Refer to the Assemb ly section, and the Assembly Dr awing and P ar ts List at the end of this manual. If any par ts are missing or broken, please call Harbor F reight T ools at the number on the cov er of this manual as soon as possib le.
Page 11 SKU 91815 Assembling the Saw to the Stand Caution: The T able Sa w body is very heavy and needs tw o people to lift. Use care when lifting. Failure to compl y may cause serious injury and damage to equipment. 1. With the help of another person, carefully lift the sa w body out of the shipping bo x and set on the ground.
Page 12 SKU 91815 Extension Wing Assembly 1. Bolt the right Extension Wing (76) to the T ab le (22) with three 5/16” x 1” Hex Cap Bolts (75), 5/16 x 23mm Flat W ashers (45), and 5/16” Lock W ashers (39). Ref er to Figures E and F , below . Hand tighten enough to hold the wing in place and allow f or adjustment.
Page 13 SKU 91815 Guide Rail Assembly 1. Attach the F ront Rail brac kets (72 and 69) to the T ab le (22) with only three 1/4” x 3/4” He x Screws (29), 1/4” Lock W ashers (14), and 1/4” Flat W ashers (2). See Figures F and G. Hex Scre ws (29) should be placed hor izontally in appro ximately the center of the slot.
Page 14 SKU 91815 8 . Before attaching the short Front Rail (72) to the left Extension Wing (76), place the Switch Plate (79) behind the lip of the left Extension Wing and line up the holes in the Switch Plate and the Extension Wing.
Page 15 SKU 91815 Assembling the Blade Guard and Splitter 1 . Inser t the blade guard support Shaft (33) and Lock W asher (34) into the curved slot at the rear of the saw Cabinet (57). Screw in the Shaft cloc kwise using an open-end wrench until securely tightened.
Page 16 SKU 91815 5 . While holding the Fence Body (50) in place, move the Fence so that it is exactly parallel to the miter fixture slot the entire length of the Fence. 6 . Tighten the four Hex Cap Bolts (38). Check the final alignment. If out of parallel, loosen the bolts and realign.
Page 17 SKU 91815 Miter Gauge Adjustment Always check to see that the Miter Gauge is accurate at 90 degrees before cutting. 1 . T o check the alignment, place the Miter Gauge in the T able slot so that the Miter Gauge body is flush with the T able edge .
Page 18 SKU 91815 10. Use the Arbor Wrench (174) to turn the Arbor Nut (101) counterclockwise to securely tighten. 11. Replace the T ab le Inser t (8) and two Screws (7). Figure L. Saw Blade Replacement Adjusting 45 and 90 Degree P ositive Stops W ARNING! A v oid serious injur y .
Page 19 SKU 91815 OPER A TING INSTRUCTIONS Controls and Indicators Figure M. T able Saw Controls and Indicators Raising, Lowering, and Tilting the Saw Blade W ARNING! A v oid serious injury . Do not raise, lower , or tilt the Saw Blade while the machine is running! Al ways turn the T able Sa w Off before adjusting the Sa w Blade.
Page 20 SKU 91815 2 . Raise the Blade Guard (10) to expose the Saw Blade. Place the stock to be cut next to the Saw Blade and adjust the Saw Blade height to 1/8” to 1/4” above the thickness of the stock. 3 . Lo w er the Blade Guard (10), making sure that the Anti-kickbac k P awls are f acing backw ard and sitting on the T able .
Page 21 SKU 91815 INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! All repairs or ser vice, aside from those procedures e xplained in this manual, should be attempted only by a qualified technician.
Page 22 SKU 91815 SA W BOD Y AND ST AND ASSEMBL Y PARTS LIST Part # Description Size Qty Part # Description Size Qty 1. Lock Knob 1 43. Scale 1 2. Flat Wash er 6 26 44. Guide Ra il (long) 1 3. Miter Gauge B ody 1 45. Flat Washer 8 14 4. Round Head S crew M5X8 1 46.
Page 23 SKU 91815 SA W BOD Y AND ST AND ASSEMBL Y DRA WING.
Page 24 SKU 91815 MO T OR AND TR UNNION ASSEMBL Y PARTS LIST Part # Descripti on Size Qty Part # Descripti on Size Qty 101 Arbor Nut 1 141 Hand Wheel H andle 2 102 Arbor Flange 1 142 Hand Wheel Scre w.
Page 25 SKU 91815 MO T OR AND TRUNNION ASSEMBL Y DRA WING.
An important point after buying a device Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools TABLE SAW - 10 INCH DIRECT DRIVE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
