Instruction/ maintenance manual of the product 91062 Harbor Freight Tools
Go to page of 17
3-1/4” ELECTRIC PLANER Model 91062 OPERA TING INSTR UCTIONS Due to continuing improv ements , actual product ma y diff er slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety warnings and precautions, assembl y , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep y our in v oice with this manual.
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4.
11. Dress properl y . Do not wear loose clothing or je welry . Contain long hair . Keep y our hair , clothing, and gloves a wa y from mo ving par ts. Loose clothes, je welr y , or long hair can be caught in moving par ts . 12. A v oid accidental star ting.
20. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that ma y affect the tool’ s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 21. Use only accessories that are recommended by the manufacturer for your model.
3. Y our tool m ust be plugged into an appropriate outlet, proper ly installed and grounded in accordance with all codes and ordinances . The plug and outlet should look like those in the f ollowing illustr ation. (See Figure A.) FIGURE A SKU 91062 P A GE 6 DOUBLE INSULA TED T OOLS: T OOLS WITH TWO PR ONG PLUGS 4.
SKU 91062 P A GE 7 EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord.
FIGURE D SKU 91062 P A GE 8 SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V olts Alternating Current Amperes No Load Revolutions per Minute (RPM) n o xxxx/min. A V ~ SPECIFIC SAFETY RULES 1. Maintain a safe working environment.
8. Use ey e and breathing protection. Alwa ys wear ANSI approv ed saf ety impact eye goggles and dust masks or a respirator when working with this product. 9. Always turn off the Planer and unplug the unit from its electrical outlet before performing any maintenance, or changing accessories.
on their own. Do not press against the Kniv es to stop them. Alwa ys keep hands and fingers clear of spinning Blades. 23. Do not for ce the Blades into the workpiece being cut. Apply moderate pres- sure, allowing the Blades to cut without being forced.
OPERA TING INSTR UCTIONS NOTE: For additional information regarding the parts mentioned in the following pages, ref er to the Assemb l y Dia gram on pa g e 17. SKU 91062 P A GE 11 The Power Switch: 1. The T r igger (16) of the Planer f eatures a Safety Loc k Button (17) to ensure against accidental star ting of the tool.
SKU 91062 P A GE 12 The Guide: 1. The Guide (64) can be used to adjust the width of cut, suppor t the Planer , and keep the Planer from drifting away from the cut line (i.e., the edge of a door). The Guide may be attached either to the right side of the Planer or on its left side.
SKU 91062 P A GE 13 the wood stoc k . Then, transfer pressure to the Rear Base Plate , and continue planing slowly to the end of the cut. Do not pull the Planer back over the surface already cut. (See Figure G.) 6. If necessar y , repeat Step #5, using progressiv ely deeper cuts until you near the desired depth.
SKU 91062 P A GE 14 driver (not included) to remov e the two Carbon Brush Caps (35). Then, remov e the two Carbon Brushes from the Brush Holders (38). If a Carbon Brush is worn down more than 1/2 of its original length, replace both Carbon Brushes.
SKU 91062 P A GE 15 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUTOR HAS PR O VIDED THE P ARTS LIST AND ASSEMBL Y DIA GRAM IN THIS MANUAL AS A REFERENCE T OOL ONL Y .
Part # Description Qty. Part # Description Qty. 1 Name Plate 1 33 Screw Arbor 1 2 Tap Screw (8SEABB04-18) 3 34 Spring 1 3 Cover 1 35 Carbon Brush Cap 2 4 Belt 1 36 Carbon Brush 2 5 Bearing Sleeve 1 37.
SKU 91062 P A GE 17 17 16 18 ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not available individually as replacement parts.
An important point after buying a device Harbor Freight Tools 91062 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 91062 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 91062 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 91062 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 91062 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 91062, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 91062.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 91062. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 91062 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
