Instruction/ maintenance manual of the product G1030 Grizzly
Go to page of 26
DUST COLLECTOR MODEL G1030 INSTRUCTION MANUAL COPYRIGHT © 1991 BY GRIZZLY INDUSTRIAL, INC. REG # 3 176 555 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY 1999.
.
G1030 Dust Collector -1- Table Of Contents PAGE 1. SAFETY ....................................................................................................................2 ADDITIONAL SAFETY INSTRUCTIONS FOR THE DUST COLLECTOR ................4 2 .
-2- G1030 Dust Collector Safety Instructions For Power Tools SECTION 1: SAFETY 7. DON’T FORCE TOOL . It will do the job better and safer at the rate for which it was designed. 8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.
G1030 Dust Collector -3- 16. REDUCE THE RISK OF UNINTENTION- AL STARTING. Make sure switch is in off position before plugging in. 17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.
-4- G1030 Dust Collector Additional Safety Instructions For The Dust Collector 4. Suspended dust particles in conjunction with an ignition source, may cause an explosion. DO NOT operate the dust collector in areas where explosion risks would be high if dust were dispersed into the area.
G1030 Dust Collector -5- SECTION 2: CIRCUIT REQUIREMENTS The motor supplied with the G1030 requires 220V service and cannot be rewired for 110V. Under normal use, the motor draws approxi- mately 18 amps @ 220V. We recommend using a 20 amp circuit breaker or a 30 amp slow-blow fuse for 220V operation.
-6- G1030 Dust Collector Figure 1. Recommended 220V receptacle. Plug/Receptacle: We recommend using the plug type illustrated in Figure 1 . Contact your local electrical contractor’s supply, a licensed electrician or our service department if you have questions about the configuration for your specific situation.
G1030 Dust Collector -7- Grizzly Industrial, Inc. is proud to offer the Model G1030 Dust Collector. These dust collectors are a part of Grizzly’s growing family of fine machin- ery.
-8- G1030 Dust Collector Unpacking The Model G1030 Dust Collector is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice.
G1030 Dust Collector -9- Site Considerations When placing the G1030 Dust Collector in your shop, two major considerations should be addressed: working clearances and electrical access and loading. 1. Working Clearances: Be sure to allow your- self sufficient room to safely operate your machines in any foreseeable operation.
-10- G1030 Dust Collector SECTION 4: ASSEMBLY Beginning Assembly Assembly of the G1030 is straightforward and can be accomplished quite easily. We have orga- nized the assembly process into logical steps. Please follow them in sequence. You will find that some pre-assembly has been done at the factory.
G1030 Dust Collector -11- Figure 3. Mounting collector to base. Figure 4. Mounting outlet to collector body. Collector Body The collector body includes the fan assembly, switch, motor and power cord which are pre- assembled at the factory.
-12- G1030 Dust Collector Collectors The left and right collectors attach to each side of the outlet flange and are later supported by the support bracket assembly. The inside of the col- lectors are funnel shaped and force the air around in a cyclone motion.
G1030 Dust Collector -13- Figure 8. Securing the bag to the collector Collection/Filter Bags bolt through one side of the clamp, then the lock nut, then thread the bolt through the other clamp. Figure 9 Hook the loops of the two upper filter bags over the upper support bracket.
-14- G1030 Dust Collector SECTION 6: OPERATIONS Please review the safety rules if you are not sure about the risks associated with operating this machine. Turn on the power supply at the main panel if not already on. Press the ON switch and be ready to switch OFF just in case there is a problem.
G1030 Dust Collector -15- For mobility, the G1030 is mounted on casters and can be moved within close proximity to your woodworking machines. You will need a flexible duct to connect each machine with a collection hood.
-16- G1030 Dust Collector System Grounding Since plastic hose is abundant, relatively inex- pensive, easily assembled, and airtight, it is a very popular material for conveying dust from woodworking machines to the dust collector. We recommend using flexible hose (flex-hose) to connect the woodworking machine to the dust collector.
G1030 Dust Collector -17- SECTION 7: MAINTENANCE Lubrication Impeller Tightening Periodic maintenance will ensure safe operation, long dust collector life, and low overall cost of operation.
-18- G1030 Dust Collector SECTION 8: CLOSURE The following pages contain general machine data, parts diagram, parts list and Warranty/Return information for your Model G1030 Dust Collector. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department.
G1030 Dust Collector -19- Design Type ...................................................................................................... Floor Model Specifications: Intake Hole Size .................................................................
REF PART # DESCRIPTION 1 P1028001 CASTER 2 PFB01 FLANGE BOLT 5 ⁄ 16 "-18 x 1 ⁄ 2 " 3 P1030003 BASE PLATE 4 PS06 PHLP HD SCREW 10-24 x 3 / 8 " 5 P1030005 INLET COVER 6 P1028007 CAP S.
2.
-22- G1030 Dust Collector Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10".
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
An important point after buying a device Grizzly G1030 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Grizzly G1030 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Grizzly G1030 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Grizzly G1030 you will learn all the available features of the product, as well as information on its operation. The information that you get Grizzly G1030 will certainly help you make a decision on the purchase.
If you already are a holder of Grizzly G1030, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Grizzly G1030.
However, one of the most important roles played by the user manual is to help in solving problems with Grizzly G1030. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Grizzly G1030 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
