Instruction/ maintenance manual of the product RTX 650 Graco
Go to page of 16
311767C Operation Interior T exture Spra yer RT X 6 5 0 For W ater- Based Materials Only Model 254973: 50 psi (3.5 bar) Maxim um Fluid W or king Pressure 100 psi (7 bar) Maxim um Air Input Pressure Related Manuals Important Safety Instructions Read all warnings and instr uctions in this manual.
Warnings 2 Wa r n i n g s The f ollowing are gener al warnings related to the set up , use , groun ding, maintenance and re pair of this equipmen t. Additional, mo re specific warnings ma y be f ound through out the body of this manu al where applicab le.
Warnings 3 Electric Shoc k Hazard T o reduce the risk of electric shock: • Be sure spr a ye r is adequately g rounded through electrical outlet . • Use only 3-wire, e xtension c ords . • Mak e sure grou nd prongs are intact on spr ay er and e xtension cords.
Warnings 4 CA UTION W ate r or mater ial remaining in unit when te mperatures are b elow freezing can dam age motor and/or dela y pump star tup . T o insure water and material are complet ely drained out of unit: 1. Remov e material line from spra yer .
Component Identification 5 Component Identification 3.5 cfm@40 min. Q M A K E B P J D C H G ti8369a F L N R Item Component Item Compone nt A Pump Hose Outle t J Bur p Guard B RotoFlex™ II Pump (insi.
Preparation 6 Preparation Pressure Relief Procedure T o reduce risk of injur y , follo w this procedur e whene ver y ou see this symbol throughout this manual, Also , perf orm this procedure whene v er you : • Stop spra ying • Check or repair any par t of this syst em • Install or clean spra y nozzle 1.
Setup 7 Setup T exture Spra ying 1. Connect air hose to user-su pplied air compressor & mater ial hose (G) t o mater ial hose outlet s . 2. Connect use r supplied air ho se to gun. 3. Open air valv e. 4. Connect material hose to gun. 5. Install spra y nozzle.
Setup 8 8. P oint gun into waste b u c ket and pull trigge r to pump water t hrough the system. Cont inue to trigger gun until material hopper is empty . 9. Install bur p guard (J). Caution , page 3. 10. Add pre-mixed texture mix to mater ial hoppe r .
Mixing Material 9 Mixing Material Dry Mix - 40 lb (18 kg) ba g. 1. Slo wly add one 40 l b . (18 kg) bag of te xture material to 5-6 gallons (18.9- 22.7 liters) of cle an water as instructed on the bag instructions . 2. Agitate to mix, using a ha lf-inch, variable speed drill with mixing paddle , to a smooth, lump-free consistency .
Spray Techniques 10 Spra y T echniques Recommended Nozzle Selection Char t 1 Control air v olume with gun air v alve . 2 F or more material v olume tr y a larger nozzle. Adjusting the System Sufficient fluid ou tput (v olume and pressure) and good atomization is a balance of atomizin g air , material thickne ss/material flow an d nozzle selection.
Shutdown and Cleanup 11 Shutdo wn and Cleanup T exture Spra ying (5 gallon Material Hopper) When you hav e finished spra ying: 1. T ur n spray er power switch (K) ON (air comp ressor can remain OFF) . 2. Close gun air v alve . 3. T rigger gun into buc ket until most of te xture mix is pumped out.
Troubleshooti ng 12 T r oubleshooting Prob lem C ause Solution Spra yer won’t r un P ower s witch not o n T ur n switch on. No pow er at wall outle t Chec k outlet by plugging in another appliance . If appliance does not work, try another outlet. Wrong size ge nerator Use a 3500 wa tt or larger gener ator .
Troubleshooting 13 Speed of a pplication slow or slower New pump hose not broken in properly Run pump d r y f or no more than 2 minutes. Material too thic k Thin material. Nozzle too small Change nozzles to a larger siz e. See Recommended Nozzle Selection Char t, page 10.
Technical Data 14 Te c h n i c a l D a t a Main Unit Po wer Re quirements . . . . . . . . . . . . . . . . . . . . 120 V a c, 60 Hz, 15A, 1 phase Maximum Fluid Working Pre ssure . . . . . . . . . . . . . . . . . . 50 psi, (3.5 bar) Maximum Air Working P ressure .
Notes 15 Notes.
Graco Warrant y 16 Graco W arranty Graco warrants all equipment ref erenced in this document which is manufactured by Gr aco and bearing its nam e to be free from de fec t s i n material and workmanship on the date of sale to the original purch aser f or use.
An important point after buying a device Graco RTX 650 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco RTX 650 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco RTX 650 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco RTX 650 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco RTX 650 will certainly help you make a decision on the purchase.
If you already are a holder of Graco RTX 650, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco RTX 650.
However, one of the most important roles played by the user manual is to help in solving problems with Graco RTX 650. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco RTX 650 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
