Instruction/ maintenance manual of the product 801-641 Graco Inc.
Go to page of 12
__ i - 1 QRllCO Rev D .~ . t. ,, ,. This manual contains IMPORTANT READ AND RETAIN FOR REFERENCE WARNINGS and lMSTAUCTlQNS P/N 800-064 SERIES A 1500 psi(103 bar) OPERATING PRESSURE 1800 psi (124 bar) .
bR]$ECTIoN HAZARD ~~~~~~~~~~~~~~~~~~~~~~~~~ penetrate the skin and cause extremely serious Fluids under high pressure from spray or leaks can injury, including the need for amputation. NEVER point the spray gun at anyone or any part of the body. NEVER put hand or fingers over the spray tip, NEVER try to stop or deflect leaks with your hand or body.
.. ENGINE KILL LEVER 7 P, LSPRAY HOSE the unit. Refer to the engine instruction booklet provided with Install Hose and Spray Gun the pin at the end of the hose into the quick Connect the spray hose to the spray gun by inserting the fluid outlet in the same way.
Startup Before startino. be sure to read the safety warninas and ~~ -. - setup instructions. Check the oil and gasoline levels daily. Turn on the water supply Trigger the gun to release any back pressure DO NOT wire or tie the gun trigger into theopen or Set the choke and open the fuel valve.
.i .. .,- ' 'ROBLEM ingine Will Not Start )r Hard To Start. Engine Misses Or Lacks 'ower .ow Pressure 'ump runs extremely rough )ressure low. Nater kaka e from under he manifolcf! Nater in pump crankcase. 'requent orprematurefailurl )f the packmg.
. .. .. 6 801-641 . . .. .. .,,".. _. . ..,, ~~. . . . ., . . . . . .. ~ .~. .. .. ~..
! I Pressure Washer Assembly, 800-064 ~ REF. PART NO. No. 1 800-130 2 '801-665 5 '801.666 4 800-081 5 801-230 6 801-129 7 801-141 8 801-542 10 801-594 9 801-131 11 801-087 12 801-942 14 801-941 13 801.
NOTE: Three sizes of metric wrenches are M10 and M6 Allen wrench. necessary for servicing the pump; M30, Valves: 1. Remove the hex plug (5)from manifold (6) using M30 wrench. 2. Examine O-ring (4) under plug and replace if cuts or distortion exist. 3.
i ~15~16 "PACKING 81 RETAINER TIl) L11'-12-14 KIT 801-664 Includes: 13 PLUNGER REPAIR REF. 'I( KIT 801 -474 NO. QTY VALVE UNIT OIL SEAL KIT Includes: 11 PACKING KIT 1 KIT 801 -472 801 -658 REF. 12 1 801-662 NO. QTY 13 1 Includes: Includes: Includes: 17' 3 14 1 REF.
SERVICE Gun, Cartridge Replacement 1. Press access pin (1 2) from gun handle and remove access plate (14) by sliding plate backwards. Remove cartridge (5) from housing (6) by using a 19 mm socket wrench. I"liri"W ..eA8,8!* 2. Check inside housing to be sure all O-rings came out when cartridge was removed.
! ENGINE BRIGGS & STRATTON 4 cycle, single cylinder air cooled, 7 hp GASOLINE TANK 4 quarts (3.79 liter) capacity WATER PUMP: 1500 PSI (103 bar) mar. pressure; 3-1 /2 GPM (13.25 liter/min). WEITED PARTS: Stainless Steel. Aluminum. Phenolic Plastic.
.. THE GRACO WARRANTY Gracolnc.warrantsallequipmentmanufacturedbyitandbear~ngitsnametobefreefromdefectsin material and workmanshlp under normal use and Seivtce.
An important point after buying a device Graco Inc. 801-641 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco Inc. 801-641 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco Inc. 801-641 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco Inc. 801-641 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco Inc. 801-641 will certainly help you make a decision on the purchase.
If you already are a holder of Graco Inc. 801-641, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco Inc. 801-641.
However, one of the most important roles played by the user manual is to help in solving problems with Graco Inc. 801-641. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco Inc. 801-641 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
