Instruction/ maintenance manual of the product Hydra-Clean 2545 Graco
Go to page of 22
INSTRUCTIONS-PARTS LIST 0-0 This mUal contains IMPORTANT WARNINGS and INSTRUCTIONS READ AND RETAIN FOR REFERENCE HYDRA-CLEAN @ 2545,3040,3235 Pressure Washers HYDRA-CLEAN 2545 PIN 800-701, Series A, 11 HP IIC ENGINE PIN 800-702, Series A, 12.
HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safety This pressure washer generates very high fluid pressure.
FUEL AND EMISSION HAZARDS NEVER flll the fuel tank while the unit is wnning or hot. NEVER alter the throttle settlng, which Is factory set. The fuel used in this unit is combustible and when Tampering with this adjustment can damage the spilled on a hot surface can ignite and cause a fire.
TERMS WARNING: Alerts user to avoid or correct conditions NOW. Identifies helpful procedures and Information. that could cause bodily injury. CAUTION: Alerts user to avoid or comect conditions that could cause damage to the equipment.
__ ~~ INSTALLATION Flgure 1 Check for Shipping Damage Check the unit for any damage that may have occurred any damage. in shipping. Notlfy the carrier Immediately if there is Set Up between the pump unloader and the high pressure If you are using a downstream chemical injector, install it hose, using the quick couplers provided.
~ ~~ STARTUP Always use this start-up procedure to ensure that the unit is started safely and properly. 1. Check oil levels. Engine: Add SA€ 30 or low-30 weigM detergent oil as necessary.
Trigger Safety Latch WARNING To reduce the risk of serious bodily injury, on the skin, ALWAYS engage the trigger safely including fluid injection, splashing in the eyes or moment. latch whenever spraying stops, even for a prevents the gun from being triggered in the engaged position, the trigger safety latch bumped.
SHUTDOWN, FLUSHING AND STORAGE WARNING Pressure Rellef Procedure To reduce the risk of serious bodily injury, including fluid injection and splashing in the eyes, .or on the skin, always follow this than 10 minutes, when shutting down, and procedure whenever you stop spraylngformore before checking or repairing any part of the system.
TROUBLESHOOTING CHART WARNING To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin or injury tom moving palls, always follow the Pressure Relief Procedure Warnlng before proceeding.
PARTS DRAWING 800-701 and 800-702.
PARTS LIST 800-701 and 800-702 Hydra-Clean@ 2545 Pressure Washer REF NO. 1 2 3 4 5 7 6 8 10 9 11 12 13 15 14 16 17 18 20 19 21 22 23 24 25 26 27 28 29 30 32 31 33 35 34 36 37 38 39 NO.
PARTS DRAWING 800-703 and 800-704 Hydra-Clean@ 3040 Pressure Washer.
PARTS LIST 800-703 and 800-704 Hydra-Cleano 3040 Pressure Washer 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 17 20 19 22 21 23 24 25 26 27 28 29 30 32 31 34 33 35 36 37 38 39 .
PARTS DRAWING 800-705 Hydra-Clea 14 308-531.
1 2 3 4 5 7 6 8 10 9 11 12 13 15 14 16 17 18 20 19 21 22 23 25 26 28 27 29 30 32 31 ""~. 800-392 NO. 100-023 801-941 801 -539 803-926 803-534 800-676 PARTS LIST 800-705 Hydra-Cleano 3235 Pressure Washer REF PART REF PART NO.
PARTS DRAWING Pump Assembly 16 308-531.
~ PARTS LIST Pump Assembly 2 1 4 3 5 6 7 8 10 9 11 12 13 14 15 16 17 18 20 19 21 22 23 25 24 26 27 28 29 30 31 32 33 34 35 37 36 REF PART NO. NO. DESCRIPTION 804-093 KEY 804-154 801 -028 804-1 89 804-.
PUMP SERVICE Servicing the Valves 1. Remove the hex valve plug. 2. Examine the O-ring under the plug for cuts or distortion and replace if wom. Lubricate new O-ring before installing. 3. Grasp valve retainer by tab at the top with pliers and remove from valve chamber.
Reassembly: V-Packlng Models: 1. Lubricate high pressure packing area in manifold. 2. Insert male adapter with notches down and "v" side UP. 3. Lubricate v-packings and install one-at-a-time with grooved side down. 4. Next install female adapter with grooved side down.
ACCESSORIES (Must be purchased separately) DOWNSTREAM CHEMICAL INJECTOR KIT WATER SANDBLASTING KIT 800-120 800-1 17 & 800-649 For injecting harsh cleaning chemicals downstream For abrasive cleaning of stubborn dirt and paint. from the pump. 800-649 is stainless steel construction.
TECHNICAL DATA Model 800-701 800-702 800-705 800-704 800-703 "Id Model Model Model Engine 11 HP B ' gs & pressure 6 quarts (5.7 liter) 24 qwls (23 lir) 6 quarts (5.
THE GRACO WARRANTY WARRANTYAND DISCLAIMERS Grawwanantsallequipmentmanutacturedbyit~baeringitsnama~obehaelmmde~~inrnaterial andwarkmanshiponthedateofsalebyanauthorizedGracodistributortotheoriginalpumhaserforuse.
An important point after buying a device Graco Hydra-Clean 2545 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco Hydra-Clean 2545 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco Hydra-Clean 2545 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco Hydra-Clean 2545 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco Hydra-Clean 2545 will certainly help you make a decision on the purchase.
If you already are a holder of Graco Hydra-Clean 2545, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco Hydra-Clean 2545.
However, one of the most important roles played by the user manual is to help in solving problems with Graco Hydra-Clean 2545. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco Hydra-Clean 2545 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
