Instruction/ maintenance manual of the product AirPro 312414 Graco
Go to page of 24
ll 2 G 312414J ENG Instr uctions-P ar ts AirPr o ™ Pressure Feed Air spra y Gun Con ventional, HVLP , and compliant guns f or specialty industrial applications. For pr ofessional use only . 100 psi (0.7 MP a, 7 bar) Maximum Air Inlet Pressure 300 psi (2.
Related Manua ls 2 312414J Contents Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Metal Spray Guns . . . . . . . . . . . . . . . . . 3 General Meta l with Stainless Steel Tip .
Models 312414J 3 Models Orifice Size in. (mm) Con ventional HVLP Compliant Model Series Max. HVLP/Compliant Air Pressure psi (MP a, bar) Model Series Max. HVLP/Compliant Air Pressure psi (MP a, bar) Model Series Max. HVLP/Compliant Air Pressure psi (MP a, bar) General Metal Spra y Guns 0.
Models 4 312414J Adhesives Spatter Gun Air Brush Stain 0.020 (0.5) 288958 A N/A 288960 A 22 (0.15, 1.5) 288962 A 29 (0.2, 2.0) 0.030 (0.8) 288959 A N/A 288961 A 22 (0.15, 1.5) 288963 A 29 (0.2, 2.0) 0.040 (1.0) 289109 A N/A 289110 A 22 (0.15, 1.5) 289111 A 29 (0.
Warnings 312414J 5 Wa r n i n g s The f ollowing w ar nings are for the setup , use, grounding, maintenance, and repair of this equip- ment. The e xclamation point symbo l aler ts you to a gener al warni ng and the hazard symbol refers to procedure-specific risk.
Gun Selection 6 312414J Gun Selection Con ventional Guns Excellent atomizati on and high production rates typically with some reduction in tr ansf er efficiency . HVLP Guns An HVLP gun is a high transf er efficiency gun which limits the air pre ssure at the air cap to 10 psi (0.
Setup 312414J 7 Setup Connect Air and Fluid Lines 1. Shut off the air supply . 2. Install a shut off valv e (not supplied) down- stream of the air regu lator to shut off gun air . 3. Install an inline air filter (not supplie d) to clean and dr y t he gun air supply .
Setup 8 312414J Adjust Spra y P attern 1. Rotate the air cap to achie ve desired spr ay patter n. See F IG . 2. 2. T o achiev e full f an patter n, open the air control v alve b y tur ning the knob fully coun- terclockwise .
Operation 312414J 9 Operation Pressure Relief Pr ocedure 1. T ur n off air and fluid supply . 2. Hold a metal part of the gun fir mly to a grounded metal pail. T r igger the gun to relie ve pressure . Appl y Fluid 1. T ur n on shop air and fluid supply to the gun.
Daily Gun Maintenance 10 312414J Dail y Gun Maintenance General T asks • F requently lubr icate the gun moving par ts with a drop of no n-silicone oil. • Do not disassemble the spra y gun if you are having a spr ay pattern problem. See T r oubleshooting , page 12, f or information on how to correct the prob lem.
Daily Gun Maintenance 312414J 11 Clean Gun 1. Flush, page 10. 2. Remov e air cap . T r i gger gun, remov e noz- zle, and soak both in a compatible solution. 3. Dip the end of a soft-b ri stle brush into a compatible solv ent. Do not continuously soak the brush's br istles with solv ent and do not use a wire brush.
Troubleshooting 12 312414J T r oubleshooting Prob lem Cause Solution Spra y P atter n N ormal patter n. No action necessar y . Spra y P atter n Dir ty or damaged air cap or fluid nozzle. Rotate air cap (13) 180°. If patter n f ollows air cap , prob- lem is in air cap .
Troubleshooting 312414J 13 Gun spitting. Air getting into paint stream. Chec k if fluid source is empty and fill. Tighten fluid nozzle (11). Check and tighten needle packing n ut (9a). Check fluid nozzle (11) f or damage. Will not spra y . Fluid c ontrol v a lv e (8) tur ned too f ar clockwise .
Repair 14 312414J Repair See Pa r t s , page 16, for callout ref erences. Disassembl y 1. Unscrew retaining r ing (14) to remov e air cap (13b). Check o- r ings (13a and 13c) and replace if necessar y . 2. T r igger gun while unscr ewing nozzle (11) to pre vent needle damage .
Repair 312414J 15 Reassembl y 1. Install air control v alve assemb ly (5) with v alve turned fully counterclockwise to out- er most position. T orque to 8 5-90 in-lb (9.6-10.2 N•m). 2. Install air inlet v alv e assemb ly (27) with v alve turned fully counterclockwise to out- er most position.
Parts 16 312414J Pa r t s 11 13c 13b 11 19 21 18 1 20 6 5 28 20 7 14 13a 10 36 27 23 8 26 9a 9b 9c 22 15 17 16 6 10 3 2 2 3 7 8 3 4 3 4 9 1 3 3 3 3 3 3 11 11 11 12 10 4 ti11194a Pull trigger before in stalling nozzle (11). Inser t spreader (15) with t apered end facing rear of gun.
Parts 312414J 17 ★ Included in Gun Repair Kit 289399. ✖ Included in T r igger Repair Kit 289143 (contains 5 of each par t). + Included in Needle P acking Repair Kit 289455 (contains 5 of each par t). * Included in Air V a lve Repair Kit 289407. ◆ Included in Air Cap Seal Kit 289791 (contains 5 of each par t).
Parts 18 312414J.
Accessories 312414J 19 Accessories Repair Kits Air V alves and Regulator s Cups Cleaning Kits T est Gauges Hoses P ar t No. Description 289455 Needle P acking Repair Kit 289399 Gun Repair Kit 289791 A.
Repair Kits 20 312414J Repair Kits Model Spray T ype Nozzle Size in. (mm) Air Cap Kit (13a-13c) Nozzle Kit (11, 19) Needle Assembly Kit (9a-9c) Needle/ Nozzle Kit (9a-9c, 11, 19 ) Needle Tip Kit (9c, 5-pack) General Metal Spray Guns 288726 Conventional 0.
Repair Kits 312414J 21 A utomotive 288929 Conventional 0.030 (0.8) 289773 289062 289271 289459 288183 288930 Conventional 0.042 (1.1) 289773 289063 289785 289460 288184 24D472* Conventional 0.042 (1.1) 289040 289063 289785 289460 288184 288931 Conventional 0.
Repair Kits 22 312414J Needle Tips W aterborne 288964 Conventional 0.030 (0.8) 289046 289071 289785 289475 288184 288965 Conventional 0.042 (1.1) 289046 289072 289785 289476 288184 288966 Conventional 0.055 (1.4) 289046 289073 289799 289477 288185 288967 HVLP 0.
Technical Data 312414J 23 Te c h n i c a l D a t a WW * Produces 10 psi (0.07 M P a, 0.7 bar) spraying pressure at air cap. ** All readings wer e taken with the f an v alve fully open . Sound power w as tested to ISO 9614-2. Air Consumption Maximum Air Inlet Pressure .
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. This manual contains English.
An important point after buying a device Graco AirPro 312414 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco AirPro 312414 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco AirPro 312414 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco AirPro 312414 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco AirPro 312414 will certainly help you make a decision on the purchase.
If you already are a holder of Graco AirPro 312414, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco AirPro 312414.
However, one of the most important roles played by the user manual is to help in solving problems with Graco AirPro 312414. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco AirPro 312414 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
