Instruction/ maintenance manual of the product 800634 Graco
Go to page of 16
308524 Rev . K INSTRUCTIONS–P ARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Belt-Drive Pressure W ashers 2545 Model 800629, Series B 2500 psi (17.2 MPa, 172 bar) Operating Pressure 2900 psi (20 MPa, 200 bar) Maximum Working Pressure 3040 Model 800632, Series B 3000 psi (20.
2 308524 T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation 5 . . . . . . . . . . . . . . . . .
308524 3 W ARNING MOVING P ARTS HAZARD Moving parts, such as the drive belt, can pinch or amputate fingers. D Keep clear of moving parts when you start or operate this equipment. D Do not operate the pressure washer without all guards and interlocks installed and functioning.
4 308524 Setup high-pressure hose connection hose rack inlet water connection 3/4” garden hose gun hose TI1262A Check for Shipping Damage Check the pressure washer for shipping damage. If anything is damaged, notify the carrier immediately . Set Up Connect the high-pressure hose between the pump outlet and the gun inlet.
308524 5 Pressure Relief Procedure INJECTION HAZARD The system pressure must be manually relieved to prevent the system from spraying accidentally . T o reduce the risk of an injury from accidental sp.
6 308524 Operation 6. Pull the starter rope to start the engine. Brace one foot on the pressure washer cart, and pull the starter rope out quickly . CAUTION Do not allow the starter rope to snap back against the engine. Let the rope recoil gently to prevent damage to the recoil mechanism.
308524 7 Operation W ater Sandblasting W ater Sandblasting Kit 244766 is available for abrasive cleaning of stubborn dirt and paint. The kit requires a sandblasting tip, sold separately as follows: D 2545 pressure washer uses sandblasting tip 805325. D 3040 pressure washer uses sandblasting tip 805317.
8 308524 Pump Service Repair kits are available. See Pump Repair Kits on page 13. For the best results, use all parts in the kits. Relieve the pressure (see page 5) before you proceed with service. NOTES: D The following metric wrenches are needed: 10 mm, 13 mm, and 30 mm.
308524 9 Pump Service 6. Lightly grease the retaining screw and the outer end of the plunger . Place the washer , o-ring, and backup ring around the screw , and install the screw through the plunger . T orque to 14.4 ft-lb (19.5 N S m). NOTE: If you plan to replace the packings, See Servicing the V -Packings at right.
34 84 19 67 51 18f 36 84 83 67 43 44 5 39 55 42 45 46 47 49 41 28 11 18a 12 13 15 14 84 85 84 55 7 4 84 55 15 86 2 22 9 84 2 86 25 9 84 10 18e 18g 18b 18d 18c 18 18h 29 30 31 32 17 38 37 48 67 6 67 26.
308524 1 1 Pressure W asher Parts Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 244450 GUN & W AND ASSEMBL Y 1 2 100023 W ASHER, flat; 3/8 4 4 801539 BUMPER 1 5 803926 .
12 308524 Pump Parts Pump Model 803297 used on 2545 Pressure W asher Pump Model 803737 used on 3040 and 3235 Pressure W ashers 19 12 12 13 14 20 18 39 40 14 15 41 21 23 22 24 32 33 26 28 27 29 25 34 3.
308524 13 Pump Parts Ref. No. Part No. Description Qty Ref. No. Part No. Description Qty 1 801467 MANIFOLD 1 2 801468 SCREW , cap, hex hd 8 3 801469 W ASHER, lock 8 4 KIT 1 O-RING 5 KIT 1 SEA T , valv.
14 308524 T roubleshooting Relieve the pressure (see page 5) before you proceed with troubleshooting. PROBLEM CAUSE SOLUTION Engine not starting or hard to start No gasoline in fuel tank or carburetor.
308524 15 T echnical Data 2545 Model 800629 3040 Model 800632 3235 Model 800634 Engine (4 cycle, air cooled) 1 1 HP Honda OHV 1 1 HP Honda OHV 1 1 HP Honda OHV Gasoline tank capacity 6.9 quarts (6.5 liters) 6.9 quarts (6.5 liters) 6.9 quarts (6.5 liters) W ater pump maximum operating pressure 2500 psi (17.
16 308524 Graco Standard W arranty Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use.
An important point after buying a device Graco 800634 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco 800634 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco 800634 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco 800634 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco 800634 will certainly help you make a decision on the purchase.
If you already are a holder of Graco 800634, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco 800634.
However, one of the most important roles played by the user manual is to help in solving problems with Graco 800634. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco 800634 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
