Instruction/ maintenance manual of the product 262605 Graco
Go to page of 28
3A1456D Operation EasyMax ™ WP Cor dless P aint Spra y er U .S. Pate nt 6,619,569; D630,708S and othe r patents pendin g Communit y Design Registration No. 0012282 55; India P atent No. 230058 China P atent No. ZL201030238 948.3; T aiwan P atent No.
Table of Contents 2 3A1456D T able of Contents W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Component Ident ification . . . . . . . . . . . . . . . . . . . . . . . . . 5 Common Pr ocedures . . . . . . . . . .
Warnings 3A1456D 3 Wa r n i n g s The follo wing war nings are for the setup, use, ma intenance, and repair of this equipment. Th e e xclamatio n point symbol aler ts y ou to a general warning and the ha zard symbols refer to procedure-sp ecific risks.
Warnings 4 3A1456D B A TTER Y HAZARD The batter y may leak, e xplode, cause b ur ns, or cause an explosion if mishandled. Contents of an open battery can cause se vere irritation and/or chemical burns. If on skin, wash with soap and w ater . If in ey es, flush with water f or at least 15 minutes and seek immediate medical attention.
Component Identification 3A1456D 5 Component Identification *NO TE: Filter asse mbly is re verse-threade d. T ur n left (or co unter-clockwise) to tigh ten, tur n rig ht (or clockwise) to loo sen.
Common Procedures 6 3A1456D Common Pr ocedures Pressure Relief Pr ocedure 1. Engage tr igger lock. 2. Put control valve UP to release pres sure. Tr i g g e r L o c k Spra y Tip P osition Contr ol V alve P osition Do not opera te or spra y near children.
Charging the Battery 3A1456D 7 Char ging the Batter y Batteries are initially 50% charge s to provide optimum battery life and requir e charging before first use. It takes approximatel y 45 minutes to charge a dead battery to 80%, at which point it can be used.
Setup 8 3A1456D Setup Suction T ube Selection This spra yer comes with two diff erent suction tubes. Standar d Suction T ube (spra ys ceilings and walls): When spra ying walls, the inlet of the suction tube should be aimed at the fr ont of the material cup .
Setup 3A1456D 9 Spra ying Stains or Clear Coats (Fine-Finish Optimizer) The Fine-Finish Optimizer should be installed an d used when spraying thin materi al such as stain or clear coats. The Fine-Finish Op timizer restricts the mat er ial flow resulting in a finer quality finish.
Setup 10 3A1456D Materials NO TE: Wh en sprayin g water-bas ed materials, flush the spra yer th oroughly with water . Star ting a New Job (or Refilling the Cup) 1.
Setup 3A1456D 11 Install Tip/Guar d Assembly (if not installed) Rever sible Tip Selection Chart 1. Engage trigger lock and put prime/relief valv e UP to release pressure . Then remove Tip/Guard Assemb ly . 2. Install filter to Spra y Tip/Guard Assembly (make sure filter is fully installed into spra yer).
Setup 12 3A1456D Basic Spra ying T echniques NO TE: Use a piece of scrap cardboa rd to practice these basic spra ying techniques bef ore you begin spr ayi ng the surf ace. Anything y ou don’t want painted that is in the area of your spraying surface shou ld be covered or remo ved.
Unclogging Spray Tip/Guard Assembly 3A1456D 13 Unc logging Spra y Tip/Guar d Assembl y Occasionally , debris from material can accumulate and clog the spra y tip. P erf or m the fo llowing steps to unclog the tip . 1. T o unclog tip obstr uction, en gage trig ger lock and pull relief valv e UP to release pressure.
Shutdown and Cleaning 14 3A1456D Shutdo wn and Cleaning Flushing Spra yer 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remo ve material cup and properly dispose cup liner or e xcess material.
Shutdown and Cleaning 3A1456D 15 6. Disconnect trigger loc k and trigger spra yer f or appro ximately 15 se conds. Engage trigger loc k. 7. Discard contaminated fluid and refill with appropr i- ate flushing fluid. 8. Disengage trigger loc k, re verse tip to UNCLOG position, an d pull tr igger for 5 seconds to prime spra yer .
Storage 16 3A1456D Cleaning Spra yer Exterior • Wipe paint off outside of spray er using a soft cloth moistened with w ater or flushing fluid . Do NO T submerge the spra yer . Tips • Tips will require replac ement depending on abrasiveness of paint.
Replacement Parts and Kits 3A1456D 17 Replacement P ar ts and Kits 1 8 11 6 5 4 3 7 12 16 ti15497a 2 15 14 17 10 18 9 19 21 20 22 13a 13 13a 13 Ref. P art Description 1 262583 Spray er , replacement (.
Repair Kit 18 3A1456D Repair Kit Outlet V alve Fitting NO TE: Before doing any repair to pump, perf or m Flushing Spra yer procedure , page 14. Re m ova l 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remove battery . 3. Remove pump outlet cap .
Alternate Priming Method 3A1456D 19 Alternate Priming Method 1. Engage tr igger lock and put p rim e/relief valve UP to release pressure . 2. Remov e material cup and f ill with flushing mater ial. 3. With spray er in pr ime mode, tur n s pra yer upside-down, remov e strainer and slowly po ur flush- ing mater ial into the intake tube u ntil full.
Alternate Priming Method 20 3A1456D Inlet V alve Cleaning Re m ova l 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remove material cup and suctio n tube. 3. Hold spr ay er upside-down and use wrench or sock et to loo sen and remove inlet fitting, inlet valv e, and spring.
Troubleshooting 3A1456D 21 T roub leshooting Chec k ev er ything in this T roubleshooting T able bef ore you br ing the spra ye r to an authorized serv ice center . Prob lem Cause Solution Spra yer mak es no sound when trigger is pulled T rigger is locked.
Troubleshooti ng 22 3A1456D Spra y Pattern Dia gnostics Spra ys with poor results Tip is pa r tially c logged See Unclog ging Tip/Guard Assembl y , page 13. Tip is not in corre ct position Rotate tip to SPR A Y po sition. Incorrect tip for application of material.
Troubleshooting 3A1456D 23 Spra y patter n is too narrow: Spra yer is too close to target surface . Incorrect tip for application of material. Tip is wor n or damaged. Mov e spra yer aw ay from surf ace (10 in). See Rever sible Tip Selection Chart, page 11.
Technical Data 24 3A1456D T e c hnical Data Sprayer: Maximum working pressure 2000 psi (137.8 bar , 13.7 MPa) W eight 6.32 lb (2.87 kg) Dimensions: Length 13.
Notes 3A1456D 25 Notes.
Notes 26 3A1456D Notes.
Notes 3A1456D 27 Notes.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. T his manual contains English.
An important point after buying a device Graco 262605 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco 262605 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco 262605 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco 262605 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco 262605 will certainly help you make a decision on the purchase.
If you already are a holder of Graco 262605, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco 262605.
However, one of the most important roles played by the user manual is to help in solving problems with Graco 262605. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco 262605 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
