Instruction/ maintenance manual of the product 2525LD Graco
Go to page of 28
309828N INSTRUCTIONS Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. G–Force Direct-Drive Pressure W asher 2525LD Model 246601, Series A & Series B 2300 psi (159 bar , 15.8 MPa) Maximum Operating Pressure 2500 psi (172 bar , 17.
2 309828 T able of Contents Symbols 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W arnings 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Component Identification 4 . . . . . . . . . . . .
3 309828 EQUI PMENT MI SUSE HAZARD: Misuse of pressure washer or accessories can cause the equipment to rupt ure or malf unction and result in serious injury . Do not alt er or modify an y part or factory–setting Check equipment daily . Repair or replac e worn or damaged part s immediat ely .
4 309828 Component Identification Gun and W and High Pressure Hose Connection On/Of f Engine Switch (side) W ater Pump Oil Fill Engine Oil Fill Tip Storage Hose Rack (a) / Gun Holder (b) (b) (a) Garde.
5 309828 Shipping Damage Check pressure washer for shipping damage. Notify carrier immediately if there is any damage. Initial Setup Oil Engine is shipped without engine oil. Add Graco SAE 10W–30 engine oil (included) and confirm oil level is within an acceptable range according to the Honda Owner ’s Manual (included).
6 309828 Installation Connect High–Pressure Hose and Gun Connect high–pressure hose between the pump outlet and gun inlet. Both of these connections are made with quick couplers. Install Spray Tip Install spray tip on wand. Installing and Changing Spray T ips, page 12).
7 309828 PRESSURE RELIEF Follow these instructions whenever you are instructed to relieve pressure, stop spraying for more than 10 minutes, check or service the equipment, or install or clean the spray nozzle. 1. Engage trigger safety latch 2. Turn pressure washer of f 3.
8 309828 1. Check oil level of engine. Startup Always use this startup procedure to ensure that the pressure washer is started safely and properly . Always engage gun trigger safety latch when you stop spraying. This reduces the risk of fluid injection or splashing in eyes or on skin if gun is bumped or accidentally triggered.
9 309828 4. T rigger gun until a constant stream of water sprays from tip indicating air is purged from the system. 5. Be sure spark plug ignition cable is pushed firmly onto spark plug. 6. For Model 2525LD ONL Y , move throttle to Rabbit (fast) position first.
10 309828 T rigger Safety Latch Always engage the safety latch when you stop spraying. Always engage trigger safety latch when you stop spraying even for a moment. The engaged safety latch prevents the gun from being triggered accidentally by hand or when dropped or bumped.
11 309828 1. Follow Pressure Relief Procedure, page 7. Chemical Injector Operation 2. Push end of chemical injector hose over chemical injector fitting on pump. Place other end in container of chemical solution. 3. Install the black, large–orifice, chemical tip.
12 309828 Spray tips have 4– or 5–digit numbers on them. The first two digits are the spray angle. T ip holding holes are provided on the chassis. 1. Perform Pressure Relief Procedure, page 7. 2. Point the gun and wand away from you and anyone else.
13 309828 Shutdown, Flushing, and Storage 1. Remove chemical injector hose from pump, if attached. 2. T rigger gun for one minute to flush pump with clear water . 3. Engage trigger safety . 4. For model 2525LD, adjust throttle to STOP position. Engine should turn off.
14 309828 5. Shut off water supply . Disconnect water supply hose from pump. 6. Remove trigger safety latch and trigger gun to relieve pressure. 7. Remove high pressure hose from pump. Drain water from all components. After each use, wipe all surfaces of pressure washer with a clean, damp cloth.
15 309828 ENGINE: 1. Run engine until gas is gone or stabilize the fuel and run it through the fuel system and carburetor . 2. Drain water out of pressure washer hose.
16 309828 Maintenance Chart Per for m Pressure Relief Procedure (page 7). Interval What to do Daily Clean water inlet screen and filter . Check engine and pump oil levels. Fill as necessary . Check gasoline level. Fill as necessary . After first 5 hours of operation Change engine break-in oil.
17 309828 T roubleshooting Perform Pressure Relief Procedure (page 7). Problem Cause Solution Engine will not start or is hard to start. No gasoline in fuel tank or carburetor Fill tank with gasoline, open fuel shutoff valve. Check fuel line and carburetor .
18 309828 Problem Cause Solution Packings are failing freq entl or Scored, damaged, or worn plungers Install new plungers. frequently or p r e m atu r e l y Abrasive material in fluid being pumped Install proper filtration on pump inlet plumbing. prematurely Inlet water temperature too high Check water temperature.
19 309828 Pump Service Repair kits are available. See the Parts Lists (page 21). For the best results, use all parts in the kits. Perform Pressure Relief Procedure (page 7). Servicing V alves Discharge V alves: Disassembly 1. Remove valve cap. 2. Inspect valve cap o–ring for damage.
20 309828 Packings Disassembly 1. T o access water seals for inspection or replace- ment, remove head of pump. Note: It is important to note the order in which the components of the packing stack are arranged and facing during disassembly . 2. Remove head bolts.
21 309828 Parts Model 2525LD 43,44 33 21 20 23 24 26 25 4 5 9 36 15 12 34 32 10 1 3 45 22 29 30 28 16 17 14 13 22 8 7 6 2 35 27 31 40 ti7343a 56.
22 309828 Parts Model 2525LD Ref. No. Part No. Description Qty . 1 15C31 1 HANDLE, cart 1 2 15B880 FRAME, placard 1 3 15C307 RACK, hose 1 4 1 15651 NUT , acorn 2 5 805535 TIP , 0 ° , red 1 6 805536 T.
23 309828 Repair Kits SJV2.5G25D–F7 (Use with model 2525LD) 66 55 63 49 47 48 43 44 46 27 30 31 32 13 14 15 17 18 19 16 21 33 36 37 28 41 2 3 4 6 6 7 8 10 11 9 5 5 12 23 24 40 1 62 26 25 38 57 35 34 ti6080c 45 SJV2.
24 309828 Parts Model 2626LD ti7344a 43,44 33 21 20 23 24 26 25 4 5 9 36 15 12 34 32 10 1 3 45 22 29 30 28 16 17 14 13 31 22 8 7 6 2 27 40 35 56.
25 309828 Parts Model 2626LD Ref. No. Part No. Description Qty . 1 15C31 1 HANDLE, cart 1 2 15F136 FRAME, placard 1 3 15C307 RACK, hose 1 4 1 15651 NUT , acorn 2 5 805535 TIP , 0 ° , red 1 6 805536 T.
26 309828 Repair Kits SJV2.5G27–D105 (Use with Model 2626LD) 55 49 47 48 43 44 46 27 30 31 32 13 14 15 17 18 19 16 21 33 36 37 28 41 10 11 9 12 23 24 40 1 2 3 4 5 6 7 8 5 6 ti6163b 62 45 63 66 38 26 25 35 34 SJV2.
27 309828 T echnical Data Model 2525LD Working pressure range Operating Pressure 2300 psi (159 bar , 15.8 MPa) Maximum Working Pressure 2500 psi (172 bar , 17.2 MPa) Engine horsepower 5.0 Maximum delivery (with nozzle) 2.5 gpm High pressure hose 30 ft x 5/16 in.
28 309828 Graco Standard W arranty Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in ma t er i al and workmanship on the date of sale to the original purchaser for use.
An important point after buying a device Graco 2525LD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco 2525LD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco 2525LD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco 2525LD you will learn all the available features of the product, as well as information on its operation. The information that you get Graco 2525LD will certainly help you make a decision on the purchase.
If you already are a holder of Graco 2525LD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco 2525LD.
However, one of the most important roles played by the user manual is to help in solving problems with Graco 2525LD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco 2525LD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
