EN
GE logo
Official user manual

GE 29

132 pages·3.1 MB·Refrigerator·PDF·ENDEITNLJA
GE 29
Table of Contents 29 sections English · Safety Instructions · Operating Instructions · Automatic Icemaker · … ShowHide
Page 1 of the GE 29 user manual — 200D2600P046 49-60371-1 09-05 JR
Page 1 · click to enlarge
Page 1

ge.com

Refrigerators

Profile Side by Side

Safety Instructions 2–4

Owner’s Manual

and Installation

Operating Instructions Automatic Icemaker 14 Care and Cleaning 16, 17 Crispers and Pans 13 CustomCool™ 7, 8 Ice and Water Dispenser 15 Refrigerator Doors 12 Replacing the Light Bulbs 18 Shelves and Bins 10, 11 Temperature Controls 5 TurboCool™ 6 Water Filter 9

Models 23, 25, 26, 27 and 29

Profile Côte à Côte

Réfrigérateurs

Manuel d’utilisation

et d’installation

La section française commence à la page 48

Installation Instructions Installing the Refrigerator 28–31 Moving the Refrigerator 24–27 Preparing to Install the Refrigerator 23 Trim Kits and Panels 19–22 Water Line Installation 32–34

Profile Lado a Lado

Refrigeradores

Manual del propietario

e instalación

Troubleshooting Tips 36–38 Normal Operating Sounds 35

La sección en español empieza en la página 90

Consumer Support Consumer Support Back Cover Performance Data Sheet 41 Product Registration (U.S.) 43, 44 Product Registration (Canadian) . . .45, 46 State of California Water Treatment Device Certificate 42 Warranty (Canadian) 39 Warranty (U.S.) 40

Write the model and serial numbers here:

Find these numbers on a label inside the refrigerator compartment at the top on the right side.

200D2600P046 49-60371-1 09-05 JR

Model # · Serial #

Page 2 of the GE 29 user manual — SAFETY PRECAUTIONS
Page 2 · click to enlarge
Page 2

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

IThis refrigerator must be properly installed

IKeep fingers out of the “pinch point” areas;

and located in accordance with the Installation Instructions before it is used.

clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

IDo not allow children to climb, stand or hang

on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

IUnplug the refrigerator before cleaning and

making repairs.

IDo not touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skin may stick to these extremely cold surfaces.

ISetting either or both controls to 0 (off) does not

IDo not store or use gasoline or other flammable

remove power to the light circuit.

vapors and liquids in the vicinity of this or any other appliance.

IDo not refreeze frozen foods which have

thawed completely.

IIn refrigerators with automatic icemakers,

IAlways clean the CustomCool™Tray after thawing

avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the icemaker. Do not place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in.

food.

Page 3 of the GE 29 user manual — USE OF EXTENSION CORDS
Page 3 · click to enlarge
Page 3

ge.com

DANGER! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous…even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.

Before You Throw Away Your Old Refrigerator or Freezer:

ITake off the doors.

ILeave the shelves in place so that children may

not easily climb inside.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

Page 4 of the GE 29 user manual — READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS
Page 4 · click to enlarge
Page 4

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

If the outlet is a standard 2-prong outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS

Page 5 of the GE 29 user manual — About the temperature controls. ge.com
Page 5 · click to enlarge
Page 5

About the temperature controls. ge.com

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings. The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating environment. Setting either or both controls to OFF stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator. NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation, remove it now.

Page 6 of the GE 29 user manual — How it Works
Page 6 · click to enlarge
Page 6

About TurboCool. ™

How it Works

TurboCool™rapidly cools the refrigerator compartment in order to more quickly cool foods. Use TurboCool when adding a large amount of food to the refrigerator compartment, putting away foods after they have been sitting out at room temperature or when putting away warm leftovers. It can also be used if the refrigerator has been without power for an extended period.

How to Use Press TurboCool. The refrigerator temperature display will show TC.

After TurboCool is complete, the refrigerator compartment will return to the original setting.

Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours. The compressor will continue to run until the refrigerator compartment cools to approximately 34°F (1°C), then it will cycle on and off to maintain this setting. After 8 hours, or if TurboCool is pressed again, the refrigerator compartment will return to the original setting.

The freezer temperature is not affected during TurboCool.

When opening the refrigerator door during TurboCool, the fans will continue to run if they have cycled on.

About ClimateKeeper2. ™

How it Works

The new ClimateKeeper2™is the industry’s most advanced refrigeration system, delivering optimum temperature and humidity performance to keep food fresh longer and reduce freezer burn, while maintaining E star-level efficiency.

The separate airflow system minimizes the mixing of air between the two compartments, which reduces odor transfer, resulting in improved taste of ice.

The ClimateKeeper2 system also reduces the number of defrosting cycles in the freezer evaporator, thereby improving the temperature maintained in the freezer and reducing freezer burn.

The new ClimateKeeper2 system features two evaporators—one for the refrigerator and one for the freezer.

*Freezer air is used in the CustomCool feature.

This provides two separate cooling systems for the entire unit, and separates the airflow between the fresh food and freezer sections during normal cooling operations.*

**Testing shows a higher level of humidity in the Fresh Food section in ClimateKeeper2 refrigerators versus conventional units.

This ensures that the humidity levels in the fresh food section are significantly higher than in a conventional system,** allowing fresh produce and other unsealed foods to retain their moisture content and freshness longer. Moisture sensitive foods such as fresh fruit, salads, rice, etc., can now be stored on open shelves without excessive moisture loss. Due to the higher humidity in the refrigerator, you may on occasion experience fog or small amounts of moisture in the refrigerator compartment. This is normal and may come and go as different food loads and environmental conditions change. Wipe dry with a paper towel if desired.

Page 7 of the GE 29 user manual — How to Remove and Replace the Drawer
Page 7 · click to enlarge
Page 7

About CustomCool ™ . ge.com

How it Works

The CustomCool™feature is a system of dampers, a fan, a temperature thermistor and a heater. Depending on the function selected, a combination of these will be used to quickly chill items, thaw items or hold the pan at a specific temperature.

Some CustomCool models feature a beverage center. It is designed to store beverages at colder temperatures. Select the Beverage Center pad if you like to keep extra-chilled refreshments on hand.

The controls for this pan are located at the top of the refrigerator with the temperature controls.

The pan is tightly sealed to prevent the pan’s temperature from causing temperature fluctuations in the rest of the refrigerator.

How to Use

I After the ExpressThaw cycle is

Empty the pan. Place the Chill/Thaw

complete, the pan will reset to the MEAT setting (32°F) to help preserve thawed items until they are used.

tray in the pan. Place the items on the tray and close the pan completely.

Select the ExpressThaw,™ExpressChill™

or SelectTemp™pad. The display and SET light will come on. Tap the pad until the light appears next to the desired setting. Use the chart to determine the best setting to use.

I The displayed actual temperature of

the CustomCool pan may vary slightly from the SET temperature based on usage and operating environment.

I To stop a feature before it is

finished, tap that feature’s pad until no options are selected and the display is off.

I During ExpressThaw and

ExpressChill,the display on the controls will count down the time in the cycle.

How to Remove and Replace the Drawer

To remove:

Lock all four swing locks by rotating

Pull the drawer out to the stop position.

them to the lock position.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing locks fit on the drawer slots.

ExpressThaw™ · ExpressChill™

Page 8 of the GE 29 user manual — CustomCool™
Page 8 · click to enlarge
Page 8
GE 29 — CustomCool™ diagram (page 8)
Fig. 1 · CustomCool™

0.5 Lb. (4 hours) I Hamburger Patties (0.5 lb)

30 Minutes I 2 to 6 Beverage Cans (12 oz each)

1.0 Lb. (6 hours) I Chicken Breasts (1.0 lb)

2.0 Lbs. (10 hours) I Chicken Breasts (2.0 lbs)

Meat Setting (32°F) I Raw Meat, Fish and Poultry

light will come on and the feature will operate as required.

How to Remove and Replace the Beverage Center Dairy Bin

bottom of the dairy bin, lift the front straight up, then lift up and out.

molded supports on adapter. Then push down on the sides of the beverage center. The beverage center will lock into place.

Page 9 of the GE 29 user manual — Installing the Filter Cartridge
Page 9 · click to enlarge
Page 9

About the water filter. (on some models) ge.com

Water Filter Cartridge The water filter cartridge is located in the back upper right corner of the refrigerator compartment.

Line up the arrow on the cartridge and the cartridge holder. Place the top of the new cartridge up inside the holder. Do not push it up into the holder.

Slowly turn it to the right until the filter cartridge stops.

When to Replace the Filter on Models With a Replacement Indicator Light There is a replacement indicator light for the water filter cartridge on the dispenser. This light will turn orange to tell you that you need to replace the filter soon.

DO NOT OVERTIGHTEN. As you turn the cartridge, it will automatically raise itself into position. The cartridge will move about 1/2 turn.

The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water to the dispenser or icemaker decreases.

When to Replace the Filter on Models Without a Replacement Indicator Light

Run water from the dispenser for 3 minutes (about 1-1/2

The filter cartridge should be replaced every six months or earlier if the flow of water to the water dispenser or icemaker decreases.

gallons) to clear the system and prevent sputtering.

Press and hold the RESET WATER FILTER pad (on some

models) on the dispenser for 3 seconds.

Removing the Filter Cartridge If you are replacing the cartridge, first remove the old one by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down.

water to spurt from the dispenser.

Filter Bypass Plug You must use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and the icemaker will not operate without the filter or filter bypass plug.

Installing the Filter Cartridge

There is an adapter attached to the top of the new filter cartridge.

If you are replacing a SmartWater cartridge, the adapter must be removed before installing the cartridge. To remove the adapter, turn it to the left about 1/4 turn.

If you are replacing a Water by Culligan cartridge, leave the adapter in place. This adapter will stay in the refrigerator when you replace future cartridges.

SmartWater Water by Culligan

To use the filter bypass plug on Water by Culligan models, you must first remove the filter adapter from the cartridge holder by turning it to the left.

If you have questions—visit our Website at ge.com, or call 1.800.GE.CARES (1.800.432.2737).

With adapter Without adapter

Replacement filters: To order additional filter cartridges in the United States, visit our Website at ge.com, or call GE Parts and Accessories, 800.626.2002.

On models without a replacement indicator light, apply the month and year sticker to the new cartridge to remind you to replace the filter in six months.

Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation.

MWF Suggested Retail $38.95–47.95

Customers in Canada should consult the yellow pages for the nearest Camco Service Center.

Show 4 more labels / short text on this page
Cartridge Holder · Filter Bypass Plug · Filter Bypass Plug · (appearance may vary)
Page 10 of the GE 29 user manual — QuickSpace ™ Shelf
Page 10 · click to enlarge
Page 10

About the shelves and bins.

Not all features are on all models.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

The snugger helps prevent tipping, spilling or sliding of small items stored on the door shelf. Place a finger on either side of the snugger near the rear and move it back and forth to fit your needs.

The larger refrigerator door bins and freezer tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight up, then lift up and out.

Do not block CAUTION: Be careful when placing items in the top bin. Make sure that items do not block or fall into the ice chute.

To replace or relocate: Engage the back side of the bin in the molded supports on the door. Then push down on the front of the bin. Bin will lock in place.

To remove: Lift the front of the bin straight up then out.

To replace: Position the bin above the rectangular molded supports on the door. Then slide the bin down onto the support to lock it in place.

reez Do not block reezer bin(on some m

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to reach items stored behind others. The special edges are designed to help prevent spills from dripping to lower shelves.

To replace or relocate:

Line the shelf up with the supports and slide it into place. The shelf can be repositioned when the door is at 90° or more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide shelf down to the desired position, line up with the supports and slide into place.

To remove:

Press tab and pull shelf forward to remove

Slide the shelf out until it reaches the stop, then press down on the tab and slide the shelf straight out.

Make sure you push the shelves all the way back in before you close the door.

QuickSpace ™ Shelf

This shelf splits in half and slides under itself for storage of tall items on the shelf below.

On some models, this shelf cannot be used in the lowest position.

This shelf can be removed and replaced or relocated just like Slide-Out Spillproof Shelves.

Show 5 more labels / short text on this page
Snugger · Large Bins · Refrigerator bin · Small Bins · Freezer tilt-out bin
Page 11 of the GE 29 user manual — Consumer Support
Page 11 · click to enlarge
Page 11

ge.com

Not all features are on all models.

Freezer Baskets

To remove, push the basket all the way to the back of the freezer. Lift up until the back pins are disengaged. Lift the entire basket up and pull out.

Make sure you push the baskets all the way back in before you close the door.

Slide-Out Freezer Shelves

To remove, slide out to the stop position, lift the front past the stop position and slide out.

Make sure you push the shelves all the way back in before you close the door.

Fixed Freezer Shelves

There are two types of fixed freezer shelves.

To remove this type of shelf:

Lift the shelf up at the left side.

Bring the shelf out.

To remove this type of shelf:

Lift up the left side of the shelf and slide it left into the center of the shelf supports.

Rotate the right side of the shelf up and out of the shelf supports.

Consumer Support

Page 12 of the GE 29 user manual — Door Alignment
Page 12 · click to enlarge
Page 12

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different than the ones you are used to. The special door opening/closing feature makes sure the doors close all the way and are securely sealed.

The resistance you feel at the stop position will be reduced as the door is loaded with food.

When opening and closing the door you will notice a stop position. If the door is opened past this stop point, the door will remain open to allow you to load and unload food more easily. When the door is only partially open, it will automatically close.

When the door is only partially open, it will automatically close. Beyond this stop the door will stay open.

Door Alignment

If doors are uneven, adjust the refrigerator door.

After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

Using a 7/16″ wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it. (A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.)

Page 13 of the GE 29 user manual — Crisper Removal
Page 13 · click to enlarge
Page 13

About the crispers and pans. ge.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the bottom of the drawers should be wiped dry.

On some models, the bottom drawer has full extension slides that allow full access to the drawer.

Adjustable Humidity Crispers

H I L O

Slide the control all the way to the HI setting to provide high humidity recommended for most vegetables.

Slide the control all the way to the LO setting to provide lower humidity levels recommended for most fruits.

Convertible Deli Pan

The convertible deli pan has its own cold air duct to allow a stream of cold air from the freezer compartment or fresh food compartment to flow to the pan.

Set the control to the coldest setting to store fresh meats.

D

O

D

O

E

S

T

Set the control to cold to convert the pan to normal refrigerator temperature and provide extra vegetable storage space. The cold air duct is turned off. Variable settings between these extremes can be selected.

The variable temperature control regulates the air flow from the Climate Keeper.

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling the drawer straight out and lifting the drawer up and over the stop location.

If the door prevents you from taking out the drawers, first try to remove the door bins. If this does not offer enough clearance, the refrigerator will need to be rolled forward until the door opens enough to slide the drawers out. In some cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you roll it out.

Page 14 of the GE 29 user manual — Automatic Icemaker
Page 14 · click to enlarge
Page 14

About the automatic icemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Icemaker

On dispenser models, to access ice or reach the power switch:

The icemaker will produce seven cubes per cycle—approximately 100–130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

Special note about dispenser models: I Dispenser models have a tilt-out ice bin.

The bin can be tilted out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the O (off) position.

I To restore your ice level from an empty

When the refrigerator has been connected to the water supply, set the power switch to the l (on) position.

bucket stage, the following steps are recommended:

12 hours after the first batch of ice has fallen into the bin, dispense 3 to 4 cubes.

Lift the bin, then pull it forward until the bin stops.

The icemaker will fill with water when it cools to 15°F (–10°C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

After an additional 6 hours, dispense 3 to 4 cubes again.

You will hear a buzzing sound each time the icemaker fills with water.

These steps will restore your ice level in the shortest amount of time.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

Lower the bin to access ice or reach the power switch. NOTE: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.

Removing Ice Bin (dispenser models)

Set the power switch to the O (off) position before removing the bin.

When replacing the bin, be sure to press it firmly into place. If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn. Then push the bin back again.

Lift the bin, then pull it forward until the bin stops.

Lift and pull forward again to remove the bin.

Show 7 more labels / short text on this page
Power Switch · Icemaker · Green Power Light · Feeler Arm · Rotate · Drive Mechanism · Dispenser Models only
Page 15 of the GE 29 user manual — Important Facts About Your Dispenser
Page 15 · click to enlarge
Page 15

About the ice and water dispenser. (on some models) ge.com

To Use the Dispenser

Select CUBED ICE , CRUSHED ICE or WATER .

Dispenser Light

This pad turns the night light in the dispenser on and off. The light also comes on when the dispenser cradle is pressed. On some models, if this light burns out, it should be replaced with a 6 watt 12V maximum bulb. Quick Ice

Press the glass gently against the top of the dispenser cradle.

The spill shelf is not self-draining. To reduce water spotting, the shelf and its grille should be cleaned regularly.

If no water is dispensed when the refrigerator is first installed, there may be air in the water line system. Press the dispenser arm for at least two minutes to remove trapped air from the water line and to fill the water system. To flush out impurities in the water line, throw away the first six glassfuls of water.

When you need ice in a hurry, press this pad to speed up ice production. This will increase ice production for the following 48 hours or until you press the pad again. Door Alarm

Press the LOCK CONTROL pad for 3 seconds to lock the dispenser and control panel. To unlock, press and hold the pad again for 3 seconds.

To set the alarm, press this pad until the indicator light comes on. This alarm will sound if either door is open for more than 3 minutes. The light goes out and the beeping stops when you close the door.

Important Facts About Your Dispenser

IDo not add ice from trays or bags to

ISome crushed ice may be dispensed

the storage drawer. It may not crush or dispense well.

even though you selected CUBED ICE. This happens occasionally when a few cubes accidentally get directed to the crusher.

IAvoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam the chute or cause the door in the chute to freeze shut. If ice is blocking the chute, poke it through with a wooden spoon.

IAfter crushed ice is dispensed, some

water may drip from the chute.

ISometimes a small mound of snow will

IBeverages and foods should not be

form on the door in the ice chute. This condition is normal and usually occurs when you have dispensed crushed ice repeatedly. The snow will eventually evaporate.

quick-chilled in the ice storage drawer. Cans, bottles or food packages in the storage drawer may cause the icemaker or auger to jam.

ITo keep dispensed ice from missing

the glass, put the glass close to, but not touching, the dispenser opening.

Spill Shelf

Page 16 of the GE 29 user manual — Cleaning the Inside
Page 16 · click to enlarge
Page 16

Care and cleaning of the refrigerator.

Cleaning the Outside

The dispenser drip area, beneath the grille, should be wiped dry. Water left in this area may leave deposits. Remove the deposits by adding undiluted vinegar to the well. Soak until the deposits disappear or become loose enough to rinse away.

The stainless steel panels and door handles (on some models) can be cleaned with a commercially available stainless steel cleaner. A spray-on stainless steel cleaner works best.

Dispenser drip area.

Do not use appliance wax or polish on the stainless steel.

The dispenser cradle. Before cleaning, lock the dispenser by pressing and holding the LOCK CONTROL pad for 3 seconds. Clean with warm water and baking soda solution—about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. Rinse thoroughly and wipe dry.

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

The door handles and trim. Clean with a cloth dampened with soapy water. Dry with a soft cloth.

Cleaning the Inside

To help prevent odors, leave an open box of baking soda in the fresh food and freezer compartments.

Use of any cleaning solution other than that which is recommended, especially those that contain petroleum distillates, can crack or damage the interior of the refrigerator.

Unplug the refrigerator before cleaning. If this is not practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls.

Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break. Handle glass shelves carefully. Bumping tempered glass can cause it to shatter.

Use warm water and baking soda solution— about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Rinse and wipe dry.

Do not wash any plastic refrigerator parts in the dishwasher.

The chill/thaw tray is dishwasher safe.

Page 17 of the GE 29 user manual — Preparing to Move
Page 17 · click to enlarge
Page 17

ge.com

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces.

When pushing the refrigerator back, make sure you don’t roll over the power cord or icemaker supply line.

Pull the refrigerator straight out and return it to position by pushing it straight in. Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator.

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator. Clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open.

If the temperature can drop below freezing, have a qualified servicer drain the water supply system to prevent serious property damage due to flooding.

Set the icemaker power switch to the O (off) position and shut off the water supply to the refrigerator.

Preparing to Move

Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage.

When using a hand truck to move the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator. Handle only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright position during moving.

Page 18 of the GE 29 user manual — Freezer Compartment
Page 18 · click to enlarge
Page 18

Replacing the light bulbs.

Setting the controls to OFF does not remove power to the light circuit.

Refrigerator Compartment—Upper Light

Unplug the refrigerator.

After replacing the bulb with an appliance bulb of the same or lower wattage, replace the light shield and screws (on some models). When replacing the light shield, make sure that the tabs at the back of the shield fit into the slots at the back of the light shield housing.

The bulbs are located at the top of the compartment, inside the light shield. On some models, a screw at the front of the light shield will have to be removed.

To remove the light shield, on some models, press in on the tabs on the sides of the shield and slide forward and out. On other models, just slide forward and out.

Plug the refrigerator back in.

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

After replacing the bulb with an appliance bulb of the same or lower wattage, replace the shield and the knob.

O

D

O

D

E

S

Unplug the refrigerator.

T

Remove the convertible meat drawer control knob by pulling straight out.

Plug the refrigerator back in.

Lift the light shield up and pull it out.

Freezer Compartment

Unplug the refrigerator.

Replace the bulb with an appliance bulb of the same or lower wattage, and reinstall the light shield. When reinstalling the light shield, make sure the top tabs snap securely into place. Replace the screw (on some models).

Remove the shelf just above the light shield. (The shelf will be easier to remove if it is emptied first.) On some models, a screw at the top of the light shield will need to be removed.

To remove the light shield, press in on the sides, and lift up and out.

Reinstall the shelf and plug the refrigerator back in.

Dispenser (on some models)

Unplug the refrigerator.

Replace the bulb with a bulb of the same size and wattage.

The bulb is located on the dispenser under the control panel. Remove the light bulb by turning it counterclockwise.

Plug the refrigerator back in.

Tabs

Page 19 of the GE 29 user manual — Before You Begin
Page 19 · click to enlarge
Page 19

Trim kits and decorator panels.

For CustomStyle™models

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that allow you to install door panels. You can order pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories, 800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4″ (6 mm) thick

When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″ cardboard, that will fit between the face of the door and the wood panel. If you are installing the pre-cut decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the decorator or wood panel and the filler panel should be 1/4″ (6 mm).

Panels 1/4″ thick or less

3/4″ (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board can be used. The raised portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm) from the handle side for fingertip clearance.

Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) max, will require that the outer 5/16″ (8 mm) of panel perimeter be no thicker than 1/4″ (6 mm).

Weight limitations for custom panels: Fresh Food 38 lbs. (17 kg) max. Freezer Door 28 lbs. (13 kg) max.

Panels thicker than 1/4″ (6 mm)

1/4″ (6 mm) Thick Backing

5/16″ (8 mm)

2″ (5.1 cm) Clearance Handle Side

1/4″ (6 mm) max

3/4″ (19 mm)

Appearance Panel Refrigerator Door

3/4″ (19 mm)

1/4″ max

Page 20 of the GE 29 user manual — Trim Kits and Panels
Page 20 · click to enlarge
Page 20
GE 29 — Trim Kits and Panels diagram (page 20)
Fig. 2 · Trim Kits and Panels

The areas at the top of the panels need to be cut out of the panels.

Cutout 1/8″ (3 mm) Cutout 1/8″ (3 mm)

The areas at the top of the panels need to be cut out of the panels.

Cutout 1/8″ (3 mm) Cutout 1/8″ (3 mm)

Page 21 of the GE 29 user manual — Trim Kits and Panels
Page 21 · click to enlarge
Page 21

Inserting the door panels.

Read these instructions completely and carefully.

Insert the Freezer Panel and Fresh Food Panel.

Carefully push the freezer panel in until it slides into the slot behind the door handle. Push the filler panel (required with some door panels) in behind the decorator panel. Repeat for fresh food panel.

If your model has a dispenser, this step only applies to the fresh food panel and top freezer panel.

Insert the Bottom Freezer Panel (on dispenser models).

Carefully push the panel in until it slides into the slot behind the door handle. Push the filler panel

(required with some door panels) in behind the decorator panel.

Attach the Top Trim on the Freezer and Fresh Food Doors.

The Top Trim can be found inside the refrigerator compartment.

each door. Hand tighten only. Make sure that the top of each panel fits snugly behind the lip of the Top Trim.

With a T-20 Torxdriver, attach the Top Trim, using two screws on each Top Trim piece, to the top of

Cut-Out Top Trim Screws

Show 7 more labels / short text on this page
Top Trim Screws · Cut-Out · Top Freezer Panel · Fresh Food Panel · Bottom Freezer Panel · Side Trim · Side Trim
Page 22 of the GE 29 user manual — Trim Kits and Panels
Page 22 · click to enlarge
Page 22
GE 29 — Trim Kits and Panels diagram (page 22)
Fig. 3 · Trim Kits and Panels

These pieces are tucked inside the refrigerator door handle.

Hold the Side Trim against the front face of the decorator panels and fit the Side Trim under the Top Trim. Make sure the magnetically attached Side Trim is fitted correctly and that you are satisfied with the appearance of all the parts.

Do not remove the protective film on the outside of the Side Trim until the Side Trim is installed.

Fit the bottom of the Side Trim under the Bottom Trim as illustrated.

Page 23 of the GE 29 user manual — TOOLS YOU WILL NEED
Page 23 · click to enlarge
Page 23

Installation Refrigerator Instructions Models 23, 25, 26, 27 & 29

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.361.3400 or Visit our Website at: geappliances.ca

BEFORE YOU BEGIN

PREPARATION WATER SUPPLY TO THE ICEMAKER

Read these instructions completely and carefully.

If the refrigerator has an icemaker, it will have to be connected to a cold water line. A GE water supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at ge.com (in Canada at geappliances.ca) or from Parts and Accessories, 800.626.2002 (in Canada 1.888.261.3055).

  • IMPORTANT — Save these instructions for local inspector’s use.
  • IMPORTANT — Observe all governing codes and ordinances.
  • Note to Installer – Be sure to leave these instructions with the Consumer.
  • Note to Consumer – Keep these instructions for future reference.
  • Skill level – Installation of this appliance requires basic mechanical skills.
  • Completion time – Refrigerator Installation 30 minutes Water Line Installation 30 minutes
  • Proper installation is the responsibility of the installer.
  • Product failure due to improper installation is not covered under the Warranty. If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving the Refrigerator ), then skip to Step 5 in Installing the Refrigerator .

TOOLS YOU WILL NEED

3/8″ and 5/16″ Socket 1/2″ and 7/16″ Wrench

1/8″ Hex Wrench

Plastic Putty Knife · Phillips Head Screwdriver

Page 24 of the GE 29 user manual — REMOVE THE BASE GRILLE
Page 24 · click to enlarge
Page 24

Installation Instructions

MOVING THE REFRIGERATOR

LOADING THE RERIGERATOR ONTO A HAND TRUCK

If the refrigerator must go through any entrance that is less than 38″ wide, the doors must be removed. Proceed to Step 3. DO NOT remove the handles. If all entrances are more than 38″ wide, skip to Installing the Refrigerator.

Leave all tape and door pads on doors until the refrigerator is in its final location. To move the refrigerator, use a padded hand truck. Center the refrigerator on the hand truck and secure the strap around the refrigerator. DO NOT OVERTIGHTEN THE STRAP.

DISCONNECT THE WATER COUPLING (on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into the bottom hinge on the freezer door that must be disconnected. To disconnect, push in on the white collar of the coupling and pull out the tubing.

REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips head screws.

White collar · Bottom freezer hinge

Page 25 of the GE 29 user manual — 90°
Page 25 · click to enlarge
Page 25

Installation Instructions

DISCONNECT THE POWER COUPLING (on some models)

CLOSE THE FREEZER AND REFRIGERATOR DOORS 6

If the refrigerator has a water dispenser, there is a power line (harness) from the cabinet into the bottom hinge on the freezer door that must be disconnected. To disconnect, pull apart at the coupling.

REMOVE THE FREEZER DOOR

A

Remove the freezer door top hinge cover (if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

DISCONNECT THE ELECTRICAL CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors (harnesses) from the cabinet into the bottom hinge on the refrigerator door that must be disconnected. To disconnect, pull apart each connector.

B

Remove the two 5/16″ or 1/8″ hex head screws, then lift the hinge straight up to free the hinge pin.

5/16″ or 1/8″ hex head

Open the freezer door to 90.°

90°

Bottom freezer hinge · Bottom refrigerator hinge

Page 26 of the GE 29 user manual — Installation Instructions
Page 26 · click to enlarge
Page 26

Installation Instructions

GE 29 — Installation Instructions diagram (page 26)
Fig. 4 · Installation Instructions

As one person slowly lifts the freezer door up and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

Remove the two 5/16″ or 1/8″ hex head screws, then lift the hinge straight up to free the hinge pin.

Set the door on a non-scratching surface with the inside up.

Remove the refrigerator door top hinge cover (if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

Page 27 of the GE 29 user manual — E
Page 27 · click to enlarge
Page 27

Installation Instructions

REMOVE THE REFRIGERATOR DOOR (cont.)

REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

D

Lift the refrigerator door up and off the bottom hinge. If the refrigerator has a refreshment center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

  • However, please note the following:
  • When lowering the doors onto the bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.
  • When connecting the water line, make sure you insert the tubing all the way to the mark.

Refreshment Center Models Only

  • Do not pinch the tubing and harnesses when placing the doors on the bottom hinges.
  • When connecting the power line and the electrical lines (refreshment center models only), be sure that the connectors are seated together fully.

E

Set the door on a non-scratching surface with the inside up.

90° · Mark

Page 28 of the GE 29 user manual — DIMENSIONS AND SPECIFICATIONS (for 25‘ CustomStyle ™ models)
Page 28 · click to enlarge
Page 28

Installation Instructions

INSTALLING THE REFRIGERATOR

  • REFRIGERATOR LOCATION
  • Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.
  • Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly.
  • Install it on a floor strong enough to support it fully loaded.

DIMENSIONS AND SPECIFICATIONS (for 23‘ CustomStyle ™ models)

701⁄4″ (178.4 cm)

CLEARANCES Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections:

36″ (91.4 cm)

23‘ (33” wide), 23‘/25‘ CustomStyle™ 25‘, 26‘, 27‘, 29‘ Sides 1/8″ (4 mm) 1/8″ (4 mm) Top 1″ (25 mm) 1″ (25 mm) Back 1/2″ (13 mm) 1″ (25 mm)

24″ (61 cm)

DIMENSIONS AND SPECIFICATIONS (for 25‘ CustomStyle ™ models)

DIMENSIONS AND SPECIFICATIONS

3/4″ (19 mm) Airspace (1/2″ [13 mm] Gap + 1/4″ [6 mm] Wall Plates) 25″ (63.5 cm) Countertop

24″ (61 cm) Cabinet

721⁄4″ (183.5 cm)*

36″ (91.4 cm)

24″ (61 cm)

*721/4″ (183.5 cm) required for full adjustment of mobility wheels. If cabinets installed above refrigerator have doors that are flush to the top of the opening for the refrigerator, then an additional 1/8″ may be required to provide clearance for cabinet doors to open freely.

Water Electrical

Page 29 of the GE 29 user manual — A
Page 29 · click to enlarge
Page 29

Installation Instructions

GE 29 — Installation Instructions diagram (page 29)
Fig. 5 · Installation Instructions

CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE (icemaker and dispenser models)

Fasten the tubing into the clamp provided to hold it in position. You may need to pry open the clamp.

A cold water supply is required for automatic icemaker and dispenser operation. If there is not a cold water supply, you will need to provide one. See Installing the Water Line section.

  • NOTES:
  • Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.
  • If your refrigerator does not have a water filter, we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator. If using GE SmartConnect ™ Refrigerator Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter. If you are using copper tubing, place a compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply. If you are using the GE SmartConnect ™ tubing, the nuts are already assembled to the tubing. If you are using copper tubing, insert the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting. If you are using GE SmartConnect ™ tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

A

B

Page 30 of the GE 29 user manual — B
Page 30 · click to enlarge
Page 30

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

PUT THE REFRIGERATOR IN PLACE

LEVEL THE REFRIGERATOR (cont.)

Move the refrigerator to its final location.

To adjust the rollers on 23 ‘/ 25 ‘ CustomStyle ™ models:

LEVEL THE REFRIGERATOR

Turn the front roller adjusting screws clockwise to raise the refrigerator, counterclockwise to lower it. Use a 3/8″ hex wrench with extension, or an adjustable wrench.

The refrigerator can be leveled by adjusting the rollers located near the bottom hinges.

These models also have rear adjustable rollers so you can align the refrigerator with your kitchen cabinets. Use a 3/8″ hex wrench with extension to turn the screws for the rear rollers—clockwise to raise the refrigerator, counterclockwise to lower it.

LEVEL THE DOORS

Adjust the refrigerator door to make the doors even at the top.

  • Rollers have three purposes:
  • Rollers adjust so the door closes easily when opened about halfway. (Raise the front about 5/8 ″ [16 mm] from the floor.)
  • Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble.
  • Rollers allow you to move the refrigerator away from the wall for cleaning.

To align: Using a 7/16″ wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it.

A

B

To adjust the rollers on 23‘ (33” wide), 25‘, 26‘, 27‘ and 29‘ models: • Turn the roller adjusting screws clockwise to raise the refrigerator, counterclockwise to lower it. Use a 3/8″ hex socket or wrench, or an adjustable wrench.

Doors should be even at top

Show 6 more labels / short text on this page
Roller adjusting screws · Raise · Rollers · Raise · Roller adjusting screw · 7/16″ wrench
Page 31 of the GE 29 user manual — Installation Instructions
Page 31 · click to enlarge
Page 31

Installation Instructions

GE 29 — Installation Instructions diagram (page 31)
Fig. 6 · Installation Instructions

Replace the grille by installing the two Phillips head screws.

Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically. It will take 2–3 days to fill the ice bin.

Page 32 of the GE 29 user manual — BEFORE YOU BEGIN
Page 32 · click to enlarge
Page 32

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER & DISPENSER MODELS)

BEFORE YOU BEGIN

WHAT YOU WILL NEED

Recommended copper water supply kits are WX8X2, WX8X3 or WX8X4, depending on the amount of tubing you need. Approved plastic water supply lines are GE SmartConnect™ Refrigerator Tubing (WX08X10002, WX08X10006, WX08X10015 and WX08X10025). When connecting your refrigerator to a GE Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow the manufacturer’s recommendations. If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter, use the refrigerator’s filter bypass plug. Using the refrigerator’s water filtration cartridge in conjunction with the RO filter can result in hollow ice cubes and slower water flow from the water dispenser. This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage. Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator. To prevent burns and product damage, do not hook up the water line to the hot water line. If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the O (off) position. Do not install the icemaker tubing in areas where temperatures fall below freezing. When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered. All installations must be in accordance with local plumbing code requirements.

  • Copper or GE SmartConnect ™ Refrigerator Tubing kit , 1/4 ″ outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square. To determine how much tubing you need: measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Then add 8 ′ (2.4 m). Be sure there is sufficient extra tubing (about 8 ′ [2.4 m] coiled into 3 turns of about 10 ″ [25 cm] diameter) to allow the refrigerator to move out from the wall after installation. GE SmartConnect ™ Refrigerator Tubing Kits are available in the following lengths: 2 ′ (0.6 m) – WX08X10002 6 ′ (1.8 m) – WX08X10006 15 ′ (4.6 m) – WX08X10015 25 ′ (7.6 m) – WX08X10025 Be sure that the kit you select allows at least 8 ′ (2.4 m) as described above.
Page 33 of the GE 29 user manual — DRILL THE HOLE FOR THE VALVE 3
Page 33 · click to enlarge
Page 33

Installation Instructions

Install the shutoff valve on the nearest frequently used drinking water line.

WHAT YOU WILL NEED (CONT.)

  • NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnect ™ Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.
  • A GE water supply kit (containing tubing, shutoff valve and fittings listed below) is available at extra cost from your dealer or from Parts and Accessories, 800.626.2002 (in Canada 1.888.261.3055).
  • A cold water supply. The water pressure must be between 20 and 120 p.s.i. (1.4–8.1 bar).

SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

CHOOSE THE VALVE LOCATION 2

Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

  • Power drill.
  • 1/2 ″ or adjustable wrench.
  • Straight and Phillips blade screwdriver.
  • Two 1/4 ″ outer diameter compression nuts and 2 ferrules (sleeves)— to connect the copper tubing to the shutoff valve and the refrigerator water valve. OR
  • If you are using a GE SmartConnect ™ Refrigerator Tubing kit, the necessary fittings are preassembled to the tubing.

DRILL THE HOLE FOR THE VALVE 3

Drill a 1/4″ hole in the water pipe (even if using a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

  • If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting. Do not cut formed end from GE SmartConnect ™ Refrigerator tubing.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced ice production or smaller cubes.

  • Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32 ″ at the point of connection to the COLD WATER LINE . Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.
Page 34 of the GE 29 user manual — ROUTE THE TUBING 6
Page 34 · click to enlarge
Page 34

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

FASTEN THE SHUTOFF VALVE 4

CONNECT THE TUBING TO THE VALVE 7

Fasten the shutoff valve to the cold water pipe with the pipe clamp.

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

Vertical Cold Water Pipe Saddle-Type Shutoff Valve

For plastic tubing from a GE SmartConnect™Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench. Overtightening may cause leaks.

Saddle-Type Shutoff Valve Compression Nut

TIGHTEN THE PIPE CLAMP 5

Tighten the clamp screws until the sealing washer begins to swell. NOTE: Do not overtighten or you may crush the tubing.

Outlet Valve Ferrule (sleeve)

Inlet End Pipe Clamp

FLUSH OUT THE TUBING 8

Turn the main water supply on and flush out the tubing until the water is clear. Shut the water off at the water valve after about one quart (1 liter) of water has been flushed through the tubing.

ROUTE THE TUBING 6

Route the tubing between the cold water line and the refrigerator. Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible. NOTE: Be sure there is sufficient extra tubing (about 8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm] diameter) to allow the refrigerator to move out from the wall after installation.

To complete the installation of the refrigerator, go back to Step 1 in Installing the Refrigerator.

Show 5 more labels / short text on this page
Pipe Clamp · SmartConnect™ Tubing · Packing Nut · Washer · Clamp Screw
Page 35 of the GE 29 user manual — CLICKS, POPS, CRACKS and CHIRPS
Page 35 · click to enlarge
Page 35

Normal operating sounds. ge.com

Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features and use newer technology.

Do you hear what I hear? These sounds are normal.

HUMMM... WHOOSH...

I The new high efficiency compressor may run faster

and longer than your old refrigerator and you may hear a high-pitched hum or pulsating sound while it is operating.

I You may hear the fans spinning at high speeds.

This happens when the refrigerator is first plugged in, when the doors are opened frequently or when a large amount of food is added to the refrigerator or freezer compartments. The fans are helping to maintain the correct temperatures.

I Sometimes the refrigerator runs for an extended period,

especially when the doors are opened frequently. This means that the Frost Guard™feature is working to prevent freezer burn and improve food preservation.

I If either door is open for over 3 minutes, you may

I You may hear a whooshing sound when the doors close.

hear the fans come on in order to cool the light bulbs.

This is due to pressure equalizing within the refrigerator.

I The fans change speeds in order to provide optimal

cooling and energy savings.

I You may hear the fans running after selecting one of

the CustomCool™ settings.

CLICKS, POPS, CRACKS and CHIRPS

WATER SOUNDS

I You may hear cracking or popping sounds when the

refrigerator is first plugged in. This happens as the refrigerator cools to the correct temperature.

I The flow of refrigerant through the freezer cooling

coils may make a gurgling noise like boiling water.

I Electronic dampers click open and closed to provide

I Water dropping on the defrost heater can cause a

optimal cooling and energy savings.

sizzling, popping or buzzing sound during the defrost cycle.

I The compressor may cause a clicking or chirping

sound when attempting to restart (this could take up to 5 minutes).

I A water dripping noise may occur during the defrost

cycle as ice melts from the evaporator and flows into the drain pan.

I The electronic control board may cause a clicking

sound when relays activate to control refrigerator components.

I Closing the door may cause a gurgling sound due to

pressure equalization.

I Expansion and contraction of cooling coils during

and after defrost can cause a cracking or popping sound.

For additional information on normal icemaker and dispenser operating sounds, see the About the automatic icemaker and About the ice and water dispenser sections.

I On models with an icemaker, after an icemaking

cycle, you may hear the ice cubes dropping into the ice bucket.

Page 36 of the GE 29 user manual — Problem Possible Causes What To Do
Page 36 · click to enlarge
Page 36

Before you call for service…

Troubleshooting Tips Save time and money! Review the charts on the following pages first and you may not need to call for service.

Problem Possible Causes What To Do

  • Refrigerator does not Refrigerator in defrost cycle.
  • Wait about 30 minutes for defrost cycle to end. operate Either or both controls set to OFF .
  • Set the controls to a temperature setting.

Refrigerator is unplugged. •Push the plug completely into the outlet.

The fuse is blown/circuit •Replace fuse or reset the breaker. breaker is tripped.

The refrigerator is in •Unplug the refrigerator and plug it back in. showroom mode.

Vibration or rattling Rollers need adjusting. •See Rollers. (slight vibration is normal)

  • Motor operates for long Normal when refrigerator
  • Wait 24 hours for the refrigerator to completely periods or cycles on and is first plugged in. cool down. off frequently. (Modern Often occurs when large
  • This is normal. refrigerators with more amounts of food are storage space and placed in refrigerator. a larger freezer require

Door left open. •Check to see if package is holding door open. more operating time.

Hot weather or frequent •This is normal. They start and stop

door openings. often to maintain even

Temperature controls set •See About the controls. temperatures.)

at the coldest setting.

Refrigerator or freezer Temperature control not set •See About the controls. compartment too warm cold enough.

Warm weather or frequent •Set the temperature control one step colder. door openings. See About the controls.

Door left open. •Check to see if package is holding door open.

Frost or ice crystals Door left open. •Check to see if package is holding door open. on frozen food Too frequent or too long (frost within package door openings. is normal)

Divider between Automatic energy saver •This helps prevent condensation on the outside. refrigerator and freezer system circulates warm compartments liquid around front edge feels warm of freezer compartment.

  • Automatic icemaker Icemaker power switch
  • Set the power switch to the on position. does not work is in the off position. Water supply turned off or
  • See Installing the water line. not connected. Freezer compartment
  • Wait 24 hours for the refrigerator to completely too warm. cool down.

Piled up cubes in the storage •Level cubes by hand. bin cause the icemaker to shut off.

Ice cubes stuck in icemaker. •Turn off the icemaker, remove cubes and turn the (Green power light on icemaker back on. icemaker blinking). 36

Page 37 of the GE 29 user manual — Troubleshooting Tips
Page 37 · click to enlarge
Page 37

ge.com

Problem Possible Causes What To Do

Frequent “buzzing” sound Icemaker power switch is in the • Set the power switch to the O (off) position. Keeping it in the I (on) position, but the water supply I (on) position will damage the water valve. to the refrigerator has not been connected.

Ice cubes have odor/taste Ice storage bin needs cleaning. • Empty and wash bin. Discard old cubes.

Food transmitting odor/taste • Wrap foods well. to ice cubes.

Interior of refrigerator • See Care and cleaning. needs cleaning.

Small or hollow cubes Water filter clogged. • Replace filter cartridge with new cartridge or with plug.

Slow ice cube freezing Door left open. • Check to see if package is holding door open.

Temperature control not set • See About the controls. cold enough.

Cube dispenser Icemaker turned off or • Turn on icemaker or water supply. does not work water supply turned off.

An item is blocking or has fallen • Remove any item that might be blocking, or has fallen into into the ice chute inside the the chute. top door bin of the freezer.

Ice cubes are frozen to • Remove cubes. icemaker feeler arm.

  • Irregular ice clumps in
  • Break up with fingertip pressure and discard remaining clumps. storage container.
  • Freezer may be too warm. Adjust the freezer control to a colder setting, one position at a time, until clumps do not form.

Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds.

Water has poor taste/odor Water dispenser has not been • Dispense water until all water in system is replenished. used for a long time.

Water in first glass is warm Normal when refrigerator • Wait 24 hours for the refrigerator to completely cool down. is first installed.

Water dispenser has not been • Dispense water until all water in system is replenished. used for a long time.

Water system has been drained. • Allow several hours for replenished supply to chill.

Water dispenser Water supply line turned • See Installing the water line. does not work off or not connected.

Water filter clogged. • Replace filter cartridge or remove filter and install plug.

Air may be trapped in the water system. • Press the dispenser arm for at least two minutes.

Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds.

Water spurting from Newly-installed filter cartridge. • Run water from the dispenser for 3 minutes (about dispenser one and a half gallons).

Water is not dispensed Water in reservoir is • Call for service. but icemaker is working frozen.

Refrigerator control setting • Set to a warmer setting. is too cold.

  • No water or ice cube Supply line or shutoff valve is clogged.
  • Call a plumber. production Water filter clogged.
  • Replace filter cartridge or remove filter and install plug.

Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds.

CUBED ICE was selected but Last setting was CRUSHED ICE. • A few cubes were left in the crusher from the previous CRUSHED ICE was dispensed setting. This is normal. 37

Page 38 of the GE 29 user manual — Problem Possible Causes What To Do
Page 38 · click to enlarge
Page 38

Before you call for service…

Problem Possible Causes What To Do

Orange glow in Defrost heater is on. •This is normal. the freezer

  • Refrigerator has odor Foods transmitting odor
  • Foods with strong odors should be tightly wrapped. to refrigerator.
  • Keep an open box of baking soda in the refrigerator; replace every three months.

Interior needs cleaning. •See Care and cleaning.

Door not closing properly Door gasket on hinge side •Apply paraffin wax to the face of the gasket. sticking or folding over.

A door bin is hitting a shelf •Move the door bin up one position. inside the refrigerator.

Moisture forms on Not unusual during periods •Wipe surface dry. outside of refrigerator of high humidity.

  • Moisture collects inside Too frequent or too long
  • This is normal for the beverage center. (in humid weather, air door openings. carries moisture into Due to the higher humidity in the
  • This is normal and may come and go as different food refrigerator when doors refrigerator, you may on occasion loads and environmental conditions change. Wipe dry are opened) experience fog or small amounts with a paper towel if desired. of moisture in the refrigerator compartment.
  • Interior light does No power at outlet.
  • Replace fuse or reset the breaker. not work Light bulb burned out.
  • See Replacing the light bulbs.

Water on kitchen floor or Cubes jammed in chute. •Poke ice through with a wooden spoon. on bottom of freezer

Hot air from bottom Normal air flow cooling motor. of refrigerator In the refrigeration process, it is normal that heat be expelled in the area under the refrigerator. Some floor coverings are sensitive and will discolor at these normal and safe temperatures.

Refrigerator never Adaptive defrost keeps •This is normal. The refrigerator will cycle off after the shuts off but the compressor running during door remains closed for 2 hours. temperatures are OK door openings.

Refrigerator beeping Door open. •Close door.

Food isn’t thawing/chilling Packaging. •Increase time or re-package in plastic.

Wrong weight selected. •Select a larger weight.

Item with high fat content. •Select a larger weight.

Not using Chill/Thaw tray. •Place items on tray and allow space in between items for better airflow.

  • Actual temperature not Unit just plugged in.
  • Allow 24 hours for system to stabilize. equal to Set temperature Door open for too long.
  • Allow 24 hours for system to stabilize.

Warm food added to refrigerator. •Allow 24 hours for system to stabilize.

Defrost cycle is in process. •Allow 24 hours for system to stabilize.

Select Temp or Beverage Refrigerator compartment •This is normal. In order to minimize energy usage, the Center feature is not temperature control is set Select Temp and Beverage Center features are disabled working at warmest setting. when the refrigerator temperature control is set at the warmest setting.

Beverage Center feature •Press Beverage Center pad to restart. turns off after six months of continuous operation. 38

Page 39 of the GE 29 user manual — CONSUMER WARRANTY
Page 39 · click to enlarge
Page 39

CONSUMER WARRANTY

(for customers in Canada)

Your refrigerator is warranted to be free of defects in material and workmanship.

What is covered How Long Warranted Parts Labour (From Date of Sale) Repair or Replace at Camco’s Option

Compressor Ten (10) Years Ten (10) Years Five (5) Years

Sealed System (including Five (5) Years Five (5) Years Five (5) Years evaporator, condenser tubing and refrigerant)

All Other Parts One (1) Year One (1) Year One (1) Year

TERMS AND CONDITIONS: This warranty applies only for single family domestic use in Canada when the Refrigerator has been properly installed according to the instructions supplied by Camco and is connected to an adequate and proper utility service. Damage due to abuse, accident, commercial use, and alteration or defacing of the serial plate cancels all obligations of this warranty. Service during this warranty must be performed by an Authorized Camco Service Agent. Neither Camco nor the Dealer is liable for any claims or damages resulting from any failure of the Refrigerator or from service delays beyond their reasonable control. To obtain warranty service, purchaser must present the original bill of sale. Components repaired or replaced are warranted through the remainder of the original warranty period only. This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within Canada. In-home warranty service will be provided in areas where it is available and deemed reasonable by Camco to provide. This warranty is in addition to any statutory warranty.

  • WHAT IS NOT COVERED:
  • Owner is responsible to pay for service calls related to product installation and/or teaching how to use the product.
  • Damage to finish must be reported within 48 hours following the delivery of the appliance.
  • Service trips to your home to teach you how to use the product.
  • Damage to finish after delivery.
  • Improper installation–proper installation includes adequate air circulation to the refrigeration system, adequate electrical, plumbing and other connecting facilities.
  • Replacement of house fuses or resetting of circuit breakers.
  • Replacement of light bulbs.
  • Damage to product caused by accident, fire, floods or acts of God.
  • Loss of food due to spoilage.
  • Proper use and care of product as listed in the owner’s manual, proper setting of controls.
  • WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES.

Camco Service is available coast to coast. If further help is needed concerning this warranty, contact: Manager, Consumer Relations, Camco Inc., Suite 310, 1 Factory Lane, Moncton, N.B. E1C 9M3 1.800.361.3400

Staple your receipt here. Proof of the original purchase date is needed to obtain service

under the warranty.

Page 40 of the GE 29 user manual — Warrantor: General Electric Company. Louisville, KY 40225
Page 40 · click to enlarge
Page 40

Refrigerator Warranty. (For customers in the United States)

Consumer Support Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions

All warranty service provided by our Factory Service Centers, or an authorized Customer Care® technician. To schedule service, on-line, 24 hours a day, visit us at ge.com, or call 800.GE.CARES (800.432.2737).

Staple your receipt here. Proof of the original purchase date is needed to obtain service

under the warranty.

For The Period Of: GE Will Replace:

One Year Any part of the refrigerator which fails due to a defect in materials or workmanship. From the date of the During this full one-year warranty, GE will also provide, free of charge, all labor and in-home original purchase service to replace the defective part.

Five Years Any part of the sealed refrigerating system (the compressor, condenser, evaporator From the date of the and all connecting tubing) which fails due to a defect in materials or workmanship. original purchase During this full five-year sealed refrigerating system warranty, GE will also provide, free of charge, all labor and in-home service to replace the defective part in the sealed refrigerating system.

Lifetime of Product The full extension slides, if they should fail due to a defect in materials or workmanship. From the date of the During this product lifetime limited warranty, you will be responsible for any labor or related original purchase service costs.

Thirty Days Any part of the water filter cartridge which fails due to a defect in materials or workmanship. From the original During this limited thirty-day warranty, GE will also provide, free of charge, a replacement water purchase date of the filter cartridge. refrigerator

What GE Will Not Cover:

IService trips to your home to teach you how to use

IReplacement of the water filter cartridge due to water

the product.

pressure that is outside the specified operating range or due to excessive sediment in the water supply.

IImproper installation, delivery or maintenance.

IReplacement of the light bulbs or water filter cartridge

IFailure of the product if it is abused, misused, or used for

other than as noted above.

other than the intended purpose or used commercially.

IDamage to the product caused by accident, fire, floods

ILoss of food due to spoilage.

or acts of God.

IReplacement of house fuses or resetting of circuit

IIncidental or consequential damage caused by possible

breakers.

defects with this appliance.

IDamage caused after delivery.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

Page 41 of the GE 29 user manual — NSF ®
Page 41 · click to enlarge
Page 41

Performance Data Sheet SmartWater Filtration System

This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.* (100% safety factors built in for unmetered usage)

Standard No. 42: Aesthetic Effects Parameter USEPA Influent Influent Effluent % Reduction Min. Required MCL Challenge Concentration Average Average Maximum Average Minimum Reduction Chlorine — 2.0 mg/L + 10% 1.96 mg/L 0.06 mg/L 0.11 mg/L 96.77% 94.74% > 50% T & O — Particulate** — at least 10,000 particles/mL 6,400,000 #/mL 58,833 #/mL 150,000 #/mL 99.14% 97.97% > 85%

Standard No. 53: Health Effects Parameter USEPA Influent Influent Effluent % Reduction Min. Required MCL Challenge Concentration Average Average Maximum Average Minimum Reduction Turbidity 1 NTU 11 + 1 NTU*** 10.5 NTU 0.14 NTU 0.28 NTU 98.54% 97.20% 0.5 NTU Cysts 99.95% Reduction Minimum 50,000 L 118,750 #/L < 1 #/L 4 #/L > 99.99% > 99.99% > 99.95% Asbestos 99% Reduction 107 to 108 fibers/L; > 10µm 57 MF/L 0.996 MF/L < 1 MF/L 99.60% 99.39% > 99% Lead at pH 6.5 0.015 mg/L 0.15 mg/L + 10% 0.1567 mg/L < 0.001 mg/L < 0.001 mg/L 99.36% 99.29% 0.010 mg/L Lead at pH 8.5 0.015 mg/L 0.15 mg/L + 10% 0.1433 mg/L < 0.001 mg/L < 0.001 mg/L 99.30% 99.29% 0.010 mg/L Mercury at pH 6.5 0.002 mg/L 0.006 mg/L + 10% 0.0059 mg/L 0.000350 mg/L 0.0007 mg/L 94.70% 87.50% 0.002 mg/L Mercury at pH 8.5 0.002 mg/L 0.006 mg/L + 10% 0.0057 mg/L 0.000325 mg/L 0.0006 mg/L 93.20% 89.29% 0.002 mg/L Alachlor 0.002 mg/L 0.04 mg/L + 10% 0.0367 mg/L 0.00023 mg/L 0.0004 mg/L 99.34% 98.67% 0.002 mg/L Lindane 0.0002 mg/L 0.002 mg/L + 10% 0.0020 mg/L < 0.00002 mg/L < 0.00002 mg/L 99.00% 98.95% 0.0002 mg/L 2,4-D 0.070 mg/L 0.210 mg/L + 10% 0.2033 mg/L 0.00337 mg/L 0.011000 mg/L 98.32% 94.50% 0.070 mg/L Toxaphene 0.003 mg/L 0.015 mg/L + 10% 0.0160 mg/L 0.00100 mg/L 0.001000 mg/L 93.44% 91.67% 0.003 mg/L Benzene 0.001 mg/L 0.015 mg/L + 10% 0.0145 mg/L 0.000500 mg/L 0.000500 mg/L 96.51% 95.83% 0.005 mg/L Carbofuran 0.040 mg/L 0.080 mg/L + 10% 0.0830 mg/L 0.001000 mg/L 0.001000 mg/L 98.78% 98.65% 0.04 mg/L 1,4 dichlorobenzene 0.075 mg/L 0.225 mg/L + 10% 0.2283 mg/L 0.000500 mg/L 0.000500 mg/L 99.78% 99.77% 0.075 mg/L Atrazine 0.003 mg/L 0.009 mg/L + 10% 0.0087 mg/L < 0.0005 mg/L < 0.0005 mg/L 94.22% 93.33% 0.003 mg/L

* Tested using a flow rate of 0.50 gpm; pressure of 60 psig; pH of 7.5 ± 0.5; temp. of 68° ± 5°F (20° ± 3°C) ** Measurement in Particles/ml. Particles used were 0.5-1 microns *** NTU=Nephelometric Turbidity units Operating Specifications

Capacity: certified for up to 300 gallons (1135 l); up to six months for models without a replacement filter indicator light;

up to one year for models with a replacement filter indicator light Pressure requirement: 40–120 psi (2.8–8.2 bar), non-shock Temperature: 33–100ºF (0.6–38ºC) Flow rate: 0.5 gpm (1.9 lpm) General Installation/Operation/Maintenance Requirements

Flush new cartridge at full flow for 3 minutes to purge out trapped air. Replace cartridge when flow becomes too slow. Special Notices

Installation instructions, parts and service availability, and standard warranty are included with the product when shipped. This drinking water system must be maintained according to manufacturer’s instructions, including replacement of filter cartridges. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or

after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water. Check for compliance with the state and local laws and regulations. Note that while the testing was performed under standard laboratory conditions, actual performance may vary. Systems must

be installed and operated in accordance with manufacturer’s recommended procedures and guidelines.

System Tested and Certified by NSF International against ANSI/NSF Standard 42 & 53 for the reduction of: Standard No. 42: Aesthetic Effects Chemical Unit

Standard No. 53Health Effects Chemical Reduction Unit

Chlorine Taste and Odor Mechanical Filtration Unit

Alachlor and Atrazine Reduction Benzene and Carbofuran Reduction 1,4 dichlorobenzene and 2,4-D Reduction Lead and Lindane Reduction Mercury and Toxaphene Reduction Mechanical Filtration Unit

NSF ®

Particulate Reduction, Class I

Turbidity Reduction Cyst and Asbestos Reduction

41 Manufactured forGeneral Electric Company, Louisville, KY 40225

MWF Cartridge

Page 42 of the GE 29 user manual — Conditions of Certification:
Page 42 · click to enlarge
Page 42

State of California Department of Health Services Water Treatment Device

Certificate Number

1698 05 -

Date IssuedFebruary 2, 2005
GE 29 — State of California Department of Health Services Water Treatment Device diagram (page 42)
Fig. 7 · State of California Department of Health Services Wa…

Trademark/Model Designation Replacement Elements

MWF MWF

ManufacturerGeneral Electric Company

The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants:

Microbiological Contaminants and Turbidity Inorganic/Radiological Contaminants

Organic Contaminants

Alachlor Atrazine Benzene Carbofuran Lindane Mercury Toxaphene 1,4-dichlorobenzene 2,4-D

300 gal Rated Service Capacity0.5 gpm Rated Service Flow:

Conditions of Certification:

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Cysts Turbidity · Asbestos Lead Mercury

Page 43 of the GE 29 user manual — General Electric Company Warranty Registration Department P.O. Box 32150 Louisville, KY 40232-2150
Page 43 · click to enlarge
Page 43

GE Service Protection Plus ™

GE, a name recognized worldwide for quality and dependability, offers you Service Protection Plus ™–comprehensive protection on all your appliances– No Matter What Brand!

  • Benefits Include:
  • Backed by GE
  • All brands covered
  • Unlimited service calls
  • All parts and labor costs included
  • No out-of-pocket expenses
  • No hidden deductibles
  • One 800 number to call

We’ll Cover Any Appliance. Anywhere. Anytime.*

You will be completely satisfied with our service protection or you may request your money back on the remaining value of your contract. No questions asked. It’s that simple.

Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more–any brand! Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable household products are protected against expensive repairs.

Place your confidence in GE and call us in the U.S. toll-free at 800.626.2224 for more information.

*All brands covered, up to 20 years old, in the continental U.S.

✁ Cut here

Please place in envelope and mail to:

General Electric Company Warranty Registration Department P.O. Box 32150 Louisville, KY 40232-2150

Page 44 of the GE 29 user manual — Model Number Serial Number
Page 44 · click to enlarge
Page 44

Consumer Product Ownership Registration

Dear Customer: Thank you for purchasing our product and thank you for placing your confidence in us. We are proud to have you as a customer!

Follow these three steps to protect your new appliance investment:

product, detach and return the form below to ensure that your product is registered, or register online at ge.com. 1 2 3

Complete and mail your Consumer Product Ownership Registration today. Have the peace of mind of knowing we can contact you in the unlikely event of a safety modification.

After mailing the registration below, store this document in a safe place. It contains information you will need should you require service. Our service number is 800.GE.CARES (800.432.2737).

Read your Owner’s Manual carefully. It will help you operate your new appliance properly.

Model Number Serial Number

Important: If you did not get a registration card with your

✁ Cut here

Consumer Product Ownership Registration

Model Number Serial Number

Mr. I Ms. I Mrs. I Miss I

Apt. #

Phone Number _ _

In Use Month Day Year

* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other important communications from GE Appliances (GEA). I Check here if you do not want to receive communications from GEA’s carefully selected partners.

FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR WARRANTY RIGHTS.

GE Consumer & Industrial Appliances General Electric Company Louisville, KY 40225 ge.com

For information about GEA's privacy and data usage policy, go to ge.com and click on "Privacy Policy" or call 800.626.2224.

Show 9 more labels / short text on this page
Mail Today! · First Name · Last Name · Street Address · E-mail Address* · Zip Code · City State · Date Placed · GE Appliances
Page 45 of the GE 29 user manual — OWNERSHIP REGISTRATION P.O. BOX 1780 MISSISSAUGA, ONTARIO L4Y 4G1
Page 45 · click to enlarge
Page 45

Please place in envelope and mail to: Veuillez mettre dans une enveloppe et envoyez à :

OWNERSHIP REGISTRATION P.O. BOX 1780 MISSISSAUGA, ONTARIO L4Y 4G1

(FOR CANADIAN CONSUMERS ONLY)

Page 46 of the GE 29 user manual — Product Registration (Canadian)
Page 46 · click to enlarge
Page 46
Page 46 of the GE 29 user manual — Product Registration (Canadian)
Page 47 of the GE 29 user manual — Product Registration (Canadian)
Page 47 · click to enlarge
Page 47
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Frequent “buzzing” soundIcemaker power switch is in the • Set the power switch to the O (off) position. Keeping it in the I (on) position, but the water supply I (on) position will damage the water valve. to the refrigerator has not been connected. p.37
Ice cubes have odor/tasteIce storage bin needs cleaning. • Empty and wash bin. Discard old cubes. Food transmitting odor/taste • Wrap foods well. to ice cubes. Interior of refrigerator • See Care and cleaning. needs cleaning. p.37
Small or hollow cubesWater filter clogged. • Replace filter cartridge with new cartridge or with plug. p.37
Slow ice cube freezingDoor left open. • Check to see if package is holding door open. Temperature control not set • See About the controls. cold enough. p.37
Cube dispenser does not workIcemaker turned off or • Turn on icemaker or water supply. water supply turned off. An item is blocking or has fallen • Remove any item that might be blocking, or has fallen into into the ice chute inside the the chute. top door bin of the freezer. Ice cubes are frozen to • Remove cubes. icemaker feeler arm. Irregular ice clumps in • Break up with fingertip pressure and discard remaining clumps. storage container. • Freezer may be too warm. Adjust the freezer control to a colder setting, one position at a time, until clumps do not form. Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds. p.37
Water has poor taste/odorWater dispenser has not been • Dispense water until all water in system is replenished. used for a long time. p.37
Water in first glass is warmNormal when refrigerator • Wait 24 hours for the refrigerator to completely cool down. is first installed. Water dispenser has not been • Dispense water until all water in system is replenished. used for a long time. Water system has been drained. • Allow several hours for replenished supply to chill. p.37
Water dispenser does not workWater supply line turned • See Installing the water line. off or not connected. Water filter clogged. • Replace filter cartridge or remove filter and install plug. Air may be trapped in the water system. • Press the dispenser arm for at least two minutes. Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds. p.37
Water spurting from dispenserNewly-installed filter cartridge. • Run water from the dispenser for 3 minutes (about one and a half gallons). p.37
Water is not dispensed but icemaker is workingWater in reservoir is • Call for service. frozen. Refrigerator control setting • Set to a warmer setting. is too cold. p.37
No water or ice cube productionSupply line or shutoff valve is clogged. • Call a plumber. Water filter clogged. • Replace filter cartridge or remove filter and install plug. Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds. p.37
CUBED ICE was selected but CRUSHED ICE was dispensedLast setting was CRUSHED ICE. • A few cubes were left in the crusher from the previous setting. This is normal. 37 p.37
Orange glow in the freezerDefrost heater is on. •This is normal. p.38
Refrigerator has odorFoods transmitting odor •Foods with strong odors should be tightly wrapped. to refrigerator. •Keep an open box of baking soda in the refrigerator; replace every three months. Interior needs cleaning. •See Care and cleaning. p.38
Door not closing properlyDoor gasket on hinge side •Apply paraffin wax to the face of the gasket. sticking or folding over. A door bin is hitting a shelf •Move the door bin up one position. inside the refrigerator. p.38
Moisture forms on outside of refrigeratorNot unusual during periods •Wipe surface dry. of high humidity. p.38
Moisture collects inside (in humid weather, air carries moisture into refrigerator when doors are opened)Too frequent or too long •This is normal for the beverage center. door openings. Due to the higher humidity in the •This is normal and may come and go as different food refrigerator, you may on occasion loads and environmental conditions change. Wipe dry experience fog or small amounts with a paper towel if desired. of moisture in the refrigerator compartment. p.38
Interior light does not workNo power at outlet. •Replace fuse or reset the breaker. Light bulb burned out. •See Replacing the light bulbs. p.38
Water on kitchen floor or on bottom of freezerCubes jammed in chute. •Poke ice through with a wooden spoon. p.38
Hot air from bottom of refrigeratorNormal air flow cooling motor. In the refrigeration process, it is normal that heat be expelled in the area under the refrigerator. Some floor coverings are sensitive and will discolor at these normal and safe temperatures. p.38
Refrigerator never shuts off but the temperatures are OKAdaptive defrost keeps •This is normal. The refrigerator will cycle off after the compressor running during door remains closed for 2 hours. door openings. p.38
Refrigerator beepingDoor open. •Close door. p.38
Food isn’t thawing/chillingPackaging. •Increase time or re-package in plastic. Wrong weight selected. •Select a larger weight. Item with high fat content. •Select a larger weight. Not using Chill/Thaw tray. •Place items on tray and allow space in between items for better airflow. p.38
Actual temperature not equal to Set temperatureUnit just plugged in. •Allow 24 hours for system to stabilize. Door open for too long. •Allow 24 hours for system to stabilize. Warm food added to refrigerator. •Allow 24 hours for system to stabilize. Defrost cycle is in process. •Allow 24 hours for system to stabilize. p.38
Select Temp or Beverage Center feature is not working 38Refrigerator compartment •This is normal. In order to minimize energy usage, the temperature control is set Select Temp and Beverage Center features are disabled at warmest setting. when the refrigerator temperature control is set at the warmest setting. Beverage Center feature •Press Beverage Center pad to restart. turns off after six months of continuous operation. p.38

Ask about the GE 29

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the GE 29

Be the first to ask — other owners or our team will answer.

Original document

GE 29 manual PDF

132 pages·3.1 MB·Refrigerator·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…