Instruction/ maintenance manual of the product Contractor Diesel Alto
Go to page of 16
CONTRACT OR DIESEL Instruktionsbog ............................. 1 - 12 Instruksjonsbok ............................. 13 - 24 Instruktionsbok ............................. 25 - 36 DA SV NO Instruction manual ........................ 37 - 48 Betriebsanleitung .
37 Congratulations! We’d like to say, “Thank You” for choosing the CONTRACTOR DIESEL. This instruction ma- nual is provided with your new High Pressure Washer to ensure that you obtain the best results, in the safest manner, with your new machine.
38 1.0 Safety E N 11. The machine must not be used in surroundings with risk of fire or explosion. 12 . Exhaust from engine and burner contains poisonous carbon monoxide gases. Avoid inhalation of exhaust gases. Never run the machine in a closed garage or confined area.
39 2.0 Motor Protection Device 3.0 Ke y photo’s E N The diesel engine is equipped with a protection device called ”Oil Alert”, which stops the engine if the oil level is insufficient. If this occurs, check the engine for leaks, and after making sure the machine is level, refill it to the proper level.
40 4. 0 Application E N 6.0 Accessories E N ALTO’s diesel powered high pressure washers can be used for all outdoor cleaning jobs for which steam, hot or cold water is used.
41 a Inlet quick-connector b Water filter c High pressure pump d Unloader/regulator (recycling valve) e Flow switch f Throttle valve g Flow switch h Burner coil i Temperature sensor j Outlet quick-con.
42 Functional description E N 7. 4 Spray lance The double spray lance is fitted with 2 nozzles, a high pressure nozzle and a low pressure nozzle. When the pressure adjustment valve (pos.
43 8.0 Connections E N 8 . 4 Suction Mode The machine is self priming, when used from a tank or stream, etc. The inlet hose must be filled with water before starting up. The self priming height depends on the water temperature. Max. self priming height of 5 m (17 ft) is reached with cold water (up to 8°C/47°F).
44 9 .0 Operating instructions E N d ) Start the machine, if stopped, and activate the spray handle to start the burner. IMPORTANT: For safety reasons it is important that instruction (a), above, alwa.
45 10.0 Storage/frost proofing 11.0 Model tag It is advisable to store the machine in a frost proof place between operations. If this is not possible the machine should be protected in the following way: 1. Disconnect the inlet hose. Remove the lance (pos.
46 12.0 Maintenance E N 2. ENGINE OIL CHANGE Refer to the Ruggerini engine manual for break- in and normal operating oil change requirements. Carry out first oil change after i0 hours of operation and then every 100 hours. Not less than once every six months, however.
47 Maintenance E N 13.0 W arranty E N 5. Leave the machine for 20 minutes. 6. Start the machine and pump the used solution into a container for proper disposal. 7. Immediately connect a fresh water supply and turn it on. 8. Start the machine, let it work for 5-10 minutes, until all the scale remover is out of the system.
14.0 T r oubleshooting E N Fault Cause Repair The engine fails to start Insufficient diesel supply Refill diesel tank. Battery run down Recharge the battery*) Fuse blown Exchange fuse. See section 3.0. The pump is frozen Let the pump thaw. Working pressure too high Nozzle partly blocked Clean the nozzle.
.
.
AL T O Danmark A/S Industrikvar teret DK-9560 Hadsund T el.: +45 7218 2100 www .alto-online.dk Printed in Denmar k Copyright © 2003 AL TO Danmark A/S 6229952 (02.
An important point after buying a device Alto Contractor Diesel (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Alto Contractor Diesel yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Alto Contractor Diesel - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Alto Contractor Diesel you will learn all the available features of the product, as well as information on its operation. The information that you get Alto Contractor Diesel will certainly help you make a decision on the purchase.
If you already are a holder of Alto Contractor Diesel, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Alto Contractor Diesel.
However, one of the most important roles played by the user manual is to help in solving problems with Alto Contractor Diesel. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Alto Contractor Diesel along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
