Instruction/ maintenance manual of the product 134940500A Frigidaire
Go to page of 24
1 www .frigidaire.com P/N 134940 5 00A (0804) Inst allation Instructions Gas & Electric Dryer Instructions d’inst allation Sécheuse à gaz ou électrique.
2 CONTENTS Pre-Installation Requirements..........................................................................................................................................2 Electrical Requirements................................................
3 GAS Dryer CIRCUIT - Individual 15 amp. branch circuit fused with a 15 amp. maximum time delay fuse or circuit breaker . POWER SUPPL Y - 3 wire, 120 volt single phase, 60 Hz, Alternating Current. POWER SUPPL Y CORD - The dryer is equipped with a 120 volt 3-wire power cord.
4 SAME AS OTHER SIDE SAME AS OTHER SIDE SAME AS OTHER SIDE SAME AS OTHER SIDE SAME AS OTHER SIDE (9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm) 4 3/8" 4 3/8" 4 3/8" 4 3/8" 4 3/8".
5 CLOSET DOOR 60 sq. inches (387.1 sq. cm) 60 sq. inches (387.1 sq. cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 1" (2.54 cm) LOCA TION OF YOUR DRYER DO NOT INST ALL YOUR DRYER: 1. In an area exposed to dripping water or outside weather conditions.
6 28. 25” to fr on t of cabi ne t 28. 75” to cl ear kn obs 29. 5” to clear door h andle 49” to clear open doo r 13. 5” 40. 75” Cen ter lin e height for rear, right, left vents 4. 37 5” Side exha us ts 27. 0” 38” Gas su pp ly pi pe on r ear of unit 2.
7 REMOVE 4 SCREWS (ONE FROM EACH HINGE FIRST) UNP UNP UNP UNP UNP ACKING ACKING ACKING ACKING ACKING 1. Using the four shipping carton corner posts (two on each side), carefully lay the dryer on its left side and remove the foam shipping base. T o prevent damage, do not use the contr ol panel as a means to pick up or move the dryer .
Figure 1 1.Open door and rem ove four (4) plugs in the door opening opposite the hinges. Retai n all parts for uses later, unless otherwise noted. (Figure 1) Note: Use care in removing plugs in not scratching paint o n the front panel. Figure 2 2. Begin removing th e four (4) screws that attach the hinge to the front panel.
Figure 7 8. Remove lens locating screw. (Figure 7) Figure 8 9. Disengaging several of the retention tabs an d pull lens away from the trans ition ring. (Figure 8) Figure 9 Figure 10 10. Remove two (2) transition ring plugs and reinstall on previous handle side.
10 ELECTRICAL INST ALLA TION ELECTRIC Dryer The following are specific requirements for proper and safe electrical installation of your dryer . Failure to follow these instructions can create electrical shock and/ or a fire hazard. This appliance MUST be properly grounded.
11 4. Thread a U.L. approved 30 amp power cord, NEMA 14-30 type ST or SRDT through the strain relief. 5. Attach the green power cord ground wire to the cabinet with the green gr ound screw .
12 GAS CONNECTION 1. Remove the shipping cap from gas pipe at the rear of the dryer . NOTE: DO NOT connect the dryer to L.P . gas service without converting the gas valve. An L.P . conversion kit must be installed by a qualified gas technician. 2.Connect a 1/2 inch (1.
13 L ’installation et le service de la Sécheuse de vêtements doivent être effectués par un installateur qualifié, l’agence de service ou le fournisseur de gaz. Installez la Sécheuse de vêtement selon les instructions du fabricant et les codes locaux.
14 ÉV ACUA TION DE L ’AIR Utiliser uniquement une conduite en métal rigide ou flexible de 10,2 cm (4 po) de diamètre (minimum) ainsi qu’une grille de sortie approuvée pourvue de clapets qui s’ouvrent lorsque la sécheuse fonctionne.
15 Pour les installations dont le circuit d'évacuation n'est pas décrit dans les tableaux, il faut utiliser la méthode suivante si le circuit d'évacuation n'est pas acceptable: 1 . Brancher un manomètre digital ou à tube incliné entre la sécheuse et le raccord d'évacuation de la sécheuse.
16 0 cm (0 po) 0 cm (0 po) 0 cm (0 po) 0 cm (0 po) 0 cm (0 po) 2,54 cm 2,54 cm 2,54 cm 2,54 cm 2,54 cm (1 po) (1 po) (1 po) (1 po) (1 po) 0 cm (0 po) 0 cm (0 po) 0 cm (0 po) 0 cm (0 po) 0 cm (0 po) 0 .
17 28.25” to front of c a bin et 28.75” to cle a r knobs 29.5” to cle ar door handle 49” to cl ear open door 13.5” 40.75” Center li ne height for rear, right, le ft vents 4.375” Side exhausts 27.0” 38” Gas supply pipe on rear of uni t 2.
18 (91,5 cm) (91,5 cm) (91,5 cm) (91,5 cm) (91,5 cm) DÉPOSER LES 4 VIS (UNE DE CHAQUE CHARNIÈRE D’ABORD) INST ALLA TION DANS UNE MAISON MOBILE 1. L ’évacuation d’air de la sécheuse DOIT se f.
Figure 1 1. Ouvrez la Porte et enlevez les 4 bouchons d' en fa ce où on trouve la charnière. Conservez toutes les pièce s po ur l es utiliser postérieurement, à moins qu 'on ne spécifie le contraire. (Figure 1). Note: Ayez des soins en enlev ant les bouchons, pour ne pas abi mer la peinture dans le Panneau Frontal.
Figure 7 8. Enlevez la vis qui fixe la lentille. (Figure 7). F igure 8 9. en séparant plusieu rs d es languettes de retenue et retirez la lentille loin de l'anneau de transition. (Figure 8). Figure 9 Figure 10 10. Enlevez deux (2) bouchons de l'ann e au de transition et reinstallez au côté précédent de la poign ée.
21 MISE À LA TERRE Sécheuses ÉLECTRIQUES non-Canadiennes Le branchement inadéquat du conducteur de mise à la terre pourrait présenter un risque choc électrique. En cas de doute quant à la mise à la terre adéquate de l’appareil, contacter un électricien agréé.
22 BRANCHEMENT ÉLECTRIQUE D’UNE INST ALLA TION À 4 FILS Sécheuses ÉLECTRIQUES non-Canadiennes 1 . Retirer les vis qui retiennent le couvercle du panneau de branchement ainsi que le support de montage du détendeur situés dans le coin supérieur à l’arrière de la sécheuse.
23 INST ALLA TION 1. BRANCHEMENT DU GAZ (Sécheuses à gaz seulement) a . Retirer le couvercle qui recouvre le tuyau de gaz à l’arrière de la sécheuse. RE MA RQ UE : NE PAS brancher la sécheuse sur une alimentation au propane sans avoir posé un nécessaire de conversion.
11 Notes ______________________________________________________________ ______________________________________________________________ ______________________________________________________________ __.
An important point after buying a device Frigidaire 134940500A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Frigidaire 134940500A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Frigidaire 134940500A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Frigidaire 134940500A you will learn all the available features of the product, as well as information on its operation. The information that you get Frigidaire 134940500A will certainly help you make a decision on the purchase.
If you already are a holder of Frigidaire 134940500A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Frigidaire 134940500A.
However, one of the most important roles played by the user manual is to help in solving problems with Frigidaire 134940500A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Frigidaire 134940500A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
