Instruction/ maintenance manual of the product EasiCut 450 Flymo
Go to page of 8
For all customer enquiries or for replacement parts, contact:- ☎ ☎ 0870 609 1901 www .flymo.com customer .services@husqvar na.co.uk EasiCut 420/EasiCut 450/ EasiCut 510 EasiCut 600XT IMPOR T ANT I.
Carton Contents IMPOR T ANT ! Please check the contents of the carton are correct BEFORE assembling your new product. IF ANY P AR TS ARE MISSING CONT ACT :- Husqvarna Outdoor Products Customer Service.
General 1. Never allow children or people unfamiliar with these instructions to use the Hedgetrimmer . Local regula- tions may restrict the age of the operator . 2. Only use the Hedgetrimmer in the manner and for the functions described in these instructions.
CABLES IMPORT ANT • Use only 1.00mm 2 size cable up to 40 metres length maximum. Maximum rating : 1.00mm 2 size cable, 10 amps 250 volts AC. • YOUR HEDGETRIMMER IS SUPPLIED WITH CABLE WIRED DIRECTL Y INTO THE PRODUCT . 1. Mains Cables and Extension Cables are avail- able from your local Approved Service Centre.
T o start your Hedgetrimmer EasiCut 420/450/510 1 . There are three switch levers fitted to your Hedgetrimmer. 2. Main switch lever (E1) and one other switch lever need to be held in the operating position (E2 or F1) for the product to start. T o start your Hedgetrimmer EasiCut 600XT 1 .
How to Use Caring for your Hedgetrimmer • WARNING Disconnect from the mains electricity sup- ply , before attempting any maintenance or adjustment. Cleaning (P) 1. Using a soft brush - remove debris from all air intakes and cutting blade. 2. Wipe over surface of your hedgetrimmer with a dry cloth.
Fault Finding Hints Fails to Operate 1. Is the Power T urned On? 2. Check the fuse in the plug, if blown replace. 3. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centr e. Cutting blade stops under load 1.
Husqvarna Outdoor Products Aycliffe Industrial Park NEWTON A YCLIFFE Co.Durham DL5 6UP ENGLAND T elephone - 0870 609 1901 Fax - 0870 609 1902 Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
An important point after buying a device Flymo EasiCut 450 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Flymo EasiCut 450 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Flymo EasiCut 450 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Flymo EasiCut 450 you will learn all the available features of the product, as well as information on its operation. The information that you get Flymo EasiCut 450 will certainly help you make a decision on the purchase.
If you already are a holder of Flymo EasiCut 450, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Flymo EasiCut 450.
However, one of the most important roles played by the user manual is to help in solving problems with Flymo EasiCut 450. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Flymo EasiCut 450 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
